BS ISO 10122-2014 Reinforcement materials Tubular braided sleeves Basis for a specification《加固材料 管状编织套管 规格基础》.pdf

《BS ISO 10122-2014 Reinforcement materials Tubular braided sleeves Basis for a specification《加固材料 管状编织套管 规格基础》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 10122-2014 Reinforcement materials Tubular braided sleeves Basis for a specification《加固材料 管状编织套管 规格基础》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS ISO 10122:2014Reinforcement materials Tubular braided sleeves Basis for a specificationBS ISO 10122:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 10122:2014.The UK participation in its preparation was entrusted to TechnicalCom

2、mittee PRI/42, Fibre reinforced thermosetting plastics andprepregs.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication

3、. The British Standards Institution 2014. Published by BSI StandardsLimited 2014ISBN 978 0 580 74665 9ICS 59.100.01Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on

4、30 September 2014.Amendments issued since publicationDate Text affectedBS ISO 10122:2014 ISO 2014Reinforcement materials Tubular braided sleeves Basis for a specificationProduits de renfort Gaines tresses Base de spcificationINTERNATIONAL STANDARDISO10122Second edition2014-09-01Reference numberISO 1

5、0122:2014(E)BS ISO 10122:2014ISO 10122:2014(E)ii ISO 2014 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2014All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including phot

6、ocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47

7、E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 10122:2014ISO 10122:2014(E) ISO 2014 All rights reserved iiiContents PageForeword iv1 Scope . 12 Normative references 13 Terms and definitions . 14 Description and designation 24.1 Technical description of tubular braided sleeves .

8、 24.2 Designation 25 Characteristics 35.1 General . 35.2 Characteristics to be specified . 35.3 Defects 46 Sampling and conditioning of specimens . 46.1 Sampling . 46.2 Conditioning of specimens . 47 Test methods . 57.1 Thickness . 57.2 Diameter, braid angle, and mass per metre length 58 Packaging a

9、nd ordering 78.1 Packaging . 78.2 Ordering data . 79 Storage 7BS ISO 10122:2014ISO 10122:2014(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carri

10、ed out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. I

11、SO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different

12、 approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be

13、the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).A

14、ny trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in

15、the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 61, Plastics, Subcommittee SC 13, Composites and reinforcement fibres.This second edition cancels and replaces the first edition (ISO 10122:1995), wh

16、ich has been technically revised.iv ISO 2014 All rights reservedBS ISO 10122:2014INTERNATIONAL STANDARD ISO 10122:2014(E)Reinforcement materials Tubular braided sleeves Basis for a specification1 ScopeThis International Standard provides a basis for specifications applicable to tubular braided sleev

17、es used as reinforcements in plastics. It deals with tubular sleeves braided from all types of yarn or roving.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edit

18、ion cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 291, Plastics Standard atmospheres for conditioning and testingISO 1887, Textile glass Determination of combustible-matter contentISO 1889, Reinforcement yarns Determinatio

19、n of linear densityISO 2797, Textile glass Rovings Basis for a specificationISO 3598, Textile glass Yarns Basis for a specificationISO 4603, Textile glass Woven fabrics Determination of thicknessISO 8516, Textile glass Textured yarns Basis for a specificationISO 10548, Carbon fibre Determination of

20、size content3 Terms and definitionsFor the purposes of this document, the following terms and definitions apply.3.1tubular braided sleevesleeve made by interlacing (braiding or plaiting) four or more yarns or rovings in such a way that they cross one another and are laid together in a helical format

21、ion3.2braidingmethod of interlacing yarns or rovings3.3constructionstructure of a sleeve, depending closely upon the type of machine used and the number of yarns or rovings per carrier3.4carrierbraiding-machine part on which the yarns or rovings are wound3.5braid angleangle between the longitudinal

22、axis of a braid and the direction of the yarns or rovings ISO 2014 All rights reserved 1BS ISO 10122:2014ISO 10122:2014(E)4 Description and designation4.1 Technical description of tubular braided sleevesThe complete description of a tubular braided sleeve requires definition of the following points:

23、a) designation of the braid yarn(s);b) construction of the sleeve;c) braid angle at a specific diameter;d) type of treatment;e) mass per metre length of the sleeve.As the full description is unwieldy, the manufacturers of tubular braided sleeves normally give a code number to their products to simpl

24、ify ordering and stocking. The full description of the braided sleeve shall, however, be given in the manufacturers catalogue against its code number.Thus, this International Standard is not meant for use in the designation of tubular braided sleeves, but is intended to be used as an aid in the prep

25、aration of standardized descriptions in the braided-sleeve catalogues and to ensure the consistency of braided sleeve identification.4.2 DesignationThe designation shall be made up of the following three groups of code-letters/numbers:a) the first group (maximum of four characters) indicates the typ

26、e or types of material used in the braiding;The following code letters shall be used to designate different types of material: G = Glass C = Carbon A = Aramid E = Ceramic P = PolyethyleneIf two or more types of material are combined in a hybrid braiding, two or more code letters shall be used.EXAMPL

27、ES CG = Carbon/glass CAE = Carbon/aramid/ceramic CGEA = Carbon/glass/ceramic/aramidIf several fibre types are used, they shall be given in order of the cross-sectional area (i.e. the mass per unit length divided by the density) of the fibre concerned, starting with the fibre having the greatest cros

28、s-sectional area.b) the second group (three digits) indicates the sleeve diameter, in millimetres, at a fibre angle of 45;c) the third group (three digits) indicates the mass, in grams per metre of sleeve, at a diameter which corresponds to a fibre angle of 45.2 ISO 2014 All rights reservedBS ISO 10

29、122:2014ISO 10122:2014(E)EXAMPLECG 024 012 Carbon / glass Diameter 24 mm Mass 12 grams per metre (Values of a g976ibre angle at 45) 5 Characteristics5.1 GeneralThe sleeve shall be of uniform structure.5.2 Characteristics to be specifiedFor relevant methods of measurement, see Clause 7.5.2.1 Construc

30、tion characteristics5.2.1.1 The type of braiding yarn or roving shall be in accordance with ISO 2797, ISO 3598, and/or ISO 8516.5.2.1.2 The construction of the sleeve shall be specified by the following:a) type(s) of yarn used on each carrier;b) linear density, in tex or decitex of the braid yarns i

31、n accordance with ISO 1889;c) number of carriers;d) type of braid;1) standard or regular braid (each carrier passes alternately under and over, or inside and outside two other carriers);2) two-by-two or paired braid (the carriers run in pairs, each pair passing alternately under and over every other

32、 pair revolving in the opposite direction);e) braid angle at a specific diameter;f) mass per metre length of the sleeve at that diameter.5.2.1.3 A roll or spool of sleeve shall be assumed to be in one piece, unless otherwise stated.5.2.1.4 The nominal thickness shall be subject to agreement between

33、supplier and buyer. It shall be given in millimetres.5.2.2 TreatmentSpecify the treatment from the following:5.2.2.1 Type of treatmenta) textile size;b) plastic size;c) desized; ISO 2014 All rights reserved 3BS ISO 10122:2014ISO 10122:2014(E)d) coupling finish;e) any other treatment.5.2.2.2 Amount o

34、f size and finishThe amount of size and finish shall be expressed as a nominal percentage by mass in accordance with ISO 1887 or ISO 10548.5.3 DefectsFor the defects listed below, the specification shall define the level of defects which can be considered acceptable and, when applicable, the method

35、of visual examination to be used.5.3.1 Braiding defects5.3.1.1 Ends out: a gap caused by a missing braiding yarn.5.3.1.2 Tight end: a braiding yarn braided under excessive tension.5.3.1.3 Stack end: a braiding yarn braided under insufficient tension.5.3.1.4 Angle deviation at a specified diameter.5.

36、3.2 Other defects5.3.2.1 Dirt: self-descriptive.5.3.2.2 Folds: self-descriptive.5.3.2.3 Grease: self-descriptive.5.3.2.4 Faulty splices: self-descriptive.6 Sampling and conditioning of specimens6.1 SamplingSamples shall be taken from the elementary unit for each delivery of a given type of tubular b

37、raided sleeve (roll or spool). The whole length of each roll selected shall be examined for defects.The number of test specimens taken from each sample shall be as specified for each test method.NOTE The elementary unit is the smallest normally commercially available entity of a given product as the

38、 following: package (single yarn, folded or cabled yarn, roving, etc.); roll (mat, woven fabric, veil, etc.); smallest physical entity in a bulk product (e.g. chopped fibres, milled fibres).6.2 Conditioning of specimensSpecimens shall be kept for at least 6 h in one of the atmospheres specified in I

39、SO 291 generally 23 C 2 C (50 10) % relative humidity unless a different conditioning atmosphere is specified.4 ISO 2014 All rights reservedBS ISO 10122:2014ISO 10122:2014(E)7 Test methods7.1 ThicknessThe method specified in ISO 4603 can be used to measure the thickness of the flattened tubular brai

40、d.7.2 Diameter, braid angle, and mass per metre lengthThe procedure described enables a tubular braided sleeve to be characterized in terms of its diameter, braid angle, and mass per metre length, the values obtained being used to generate a designation code.7.2.1 Apparatus7.2.1.1 Circular tube or s

41、haft with a diameter which gives a fibre angle between 20 and 70 relative to the axis of the tube.It is advisable to use a tube or shaft with a length between 500 mm and 1 000 mm. The walls of the tube shall not deviate from parallel by more than 5 %.7.2.1.2 Vernier callipers reading to 0,1 mm and a

42、ccurate to 0,5 mm, for measuring the diameter of the tube.7.2.1.3 Rule reading to 0,5 mm, to measure the length of the tube and the length of a yarn or roving taken from the specimen.7.2.1.4 Balance reading to 0,01 g and accurate to 0,05 g, to determine the mass of the specimen.7.2.1.5 Pair of sciss

43、ors or knife, suitable for cutting the specimen.7.2.2 ConditioningSee 6.2.7.2.3 ProcedureMeasure the diameter and length in millimetres of the tube or shaft.Pull the sleeve over the tube or shaft without leaving any slack and cut off a specimen with the same length as the tube.Determine the mass in

44、grams of the specimen.Take a yarn or roving from the specimen and measure its length, in millimetres.Calculate the braid angle (see 7.2.5.1).Calculate the diameter at a braid angle of 45 (see 7.2.5.2).Calculate the mass per metre length at a braid angle of 45 (see 7.2.5.3).7.2.4 Designation codeGene

45、rate the designation code as specified in 4.2. ISO 2014 All rights reserved 5BS ISO 10122:2014ISO 10122:2014(E)7.2.5 Calculations7.2.5.1 Braid angleThe braid angle t, in degrees of the sleeve as it sits on the tube or shaft is calculated using Formula (1):costtv=LL(1)whereLtis the length, in millime

46、tres of the tube or shaft;Lvis the length, in millimetres of the yarn or roving taken from the specimen.7.2.5.2 Diameter at braid angle of 45The diameter D45, in millimetres of the sleeve at a braid angle of 45 is calculated using Formula (2):DD45052= ,sintt(2)whereDtis the diameter, in millimetres

47、of the tube;tis the braid angle, in degrees.7.2.5.3 Mass per metre lengtha) The mass per metre length W45, in grams per metre, at a braid angle of 45 is calculated (when 0 rovings are not used) using Formula (3):WmL450051000 2=,cosvt (3)wherem0is the mass, in grams, of the specimen,Lvis the length,

48、in millimetres, of the yarn or roving taken from the specimen;tis the braid angle, in degrees.b) The mass per metre length W, in grams per metre, calculated from the number of carriers at a braid angle of t, is given by Formula (4):6 ISO 2014 All rights reservedBS ISO 10122:2014ISO 10122:2014(E)WNnW

49、ii= cost(4)whereN is the number of carriers;niis the number of yarns per carrier;Wiis the linear density, in grams per metre, of the individual yarns;tis the braid angle, in degrees.8 Packaging and ordering8.1 PackagingThe packaging required to ensure that the quality of the tubular braided sleeve does not deteriorate during transportation and storage shall be precisely described in the specification.8.2 Ordering data8.2.1 Title, number, and date of the specificatio