BS EN ISO 6413-1995 Technical drawings - Representation of splines and serrations《技术制图 花键和锯齿形花健的表示法》.pdf
《BS EN ISO 6413-1995 Technical drawings - Representation of splines and serrations《技术制图 花键和锯齿形花健的表示法》.pdf》由会员分享,可在线阅读,更多相关《BS EN ISO 6413-1995 Technical drawings - Representation of splines and serrations《技术制图 花键和锯齿形花健的表示法》.pdf(14页珍藏版)》请在麦多课文档分享上搜索。
1、BRITISH STANDARD BS ENISO 6413:1995 BS308-1.9: 1995 Technical drawings Representation of splines and serrations The European Standard EN ISO6413:1994 has the status of a British StandardBSENISO6413:1995 This British Standard, having been prepared under the direction of the Engineering Sector Board,
2、was published under the authority of the Standards Board and comes into effect on 15 September 1995 BSI 03-1999 The following BSI references relate to the work on this standard: Committee reference TDE/4 Draft announced in BSI News August 1995 ISBN 0 580 23774 5 Committees responsible for this Briti
3、sh Standard The preparation of this British Standard was entrusted to Technical Committee TDE/4, Engineering drawing practice, upon which the following bodies were represented: Atomic Weapons Establishment British Gas plc British Standards Society Drawing Office Material Manufacturers and Dealers As
4、sociation Electricity Association Gauge and Tool Makers Association HEVAC Association Institution of Chemical Engineers Institution of Engineering Designers Power Generation Contractors Association Society of British Aerospace Companies Ltd. University of Warwick Amendments issued since publication
5、Amd. No. Date CommentsBSENISO6413:1995 BSI 03-1999 i Contents Page Committees responsible Inside front cover National foreword ii Foreword 2 1 Scope 3 2 Normative references 3 3 Definitions 3 4 Designation 3 5 Complete representation of spline joints 4 6 Simplified representation 4 7 Assembly drawin
6、gs 6 Annex A (normative) Proportions and dimensions of graphical symbols 8 Figure 1 3 Figure 2 3 Figure 3 4 Figure 4 4 Figure 5 4 Figure 6 4 Figure 7 6 Figure 8 6 Figure 9 6 Figure 10 6 Figure 11 6 Figure 12 6 Figure 13 7 Figure 14 7 Figure A.1 8 Figure A.2 8 Table 1 Simplified representation 5 Tabl
7、e A.1 Dimensions 8 List of references Inside back coverBSENISO6413:1995 ii BSI 03-1999 National foreword This British Standard has been prepared by Technical Committee TDE/4 and is the English language version of EN ISO6413:1994 Technical drawings Representation of splines and serrations, published
8、by the European Committee for Standardization (CEN). It is identical with ISO6413:1988, published by the International Organization for Standardization (ISO). This British Standard partially supersedes BS308-1. It is envisaged that when the full range of European Standards on technical drawing is im
9、plemented BS308will be withdrawn. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-r
10、eferences Publication referred to Corresponding British Standard ISO14:1982 BS5686:1986Specification for straight-sided splines for cylindrical shafts: metric nominal dimensions, tolerances and gauging requirements BS308Engineering drawing practice ISO128:1982 Part1:1993Recommendations for general p
11、rinciples ISO3098-1:1974 Part1:1993Recommendations for general principles ISO4156:1981 BS6186Specification for straight cylindrical involute splines: metric module side fit Part1:1981Dimensions and tolerances Summary of pages This document comprises a front cover, an inside front cover, pagesiand ii
12、, theEN title page, pages2 to8, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO6413 Oc
13、tober1994 ICS 01.100.20; 21.120.30 Descriptors: Drawings, technical drawings, splines, graphic methods English version Technical drawings Representation of splines andserrations (ISO6413:1988) Dessins techniques Reprsentation des cannelures et des dentelures (ISO6413:1988) Technische Zeichnungen Dar
14、stellung von Keilwellen und Kerbverzahnungen (ISO6413:1988) This European Standard was approved by CEN on1994-10-14. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without an
15、y alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by
16、 translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Lux
17、embourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart36, B-1050Brussels 1994Copyright reserved to CEN members Ref. No. EN ISO
18、6413:1994 EENISO6413:1994 BSI 03-1999 2 Foreword This European Standard was taken over by CEN from the work of ISO/TC10, Technical drawings, product definition and related documentation, of the International Standards Organization (ISO). The Technical Board had decided to submit the final draft for
19、Formal Vote. The result was positive. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 1995, and conflicting national standards shall be withdrawn at the latest by April 1995. According to th
20、e CEN/CENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, United Kingdom.ENISO6413:1994 BSI 03
21、-1999 3 1 Scope This International Standard specifies the rules and graphical symbols for the representations of splines and serrations on technical drawings. Two methods of representation are specified as follows: a) true representation; b) simplified representation. The rules and graphical symbols
22、 specified in this International Standard are applicable to detail drawings of the parts (shafts and hubs) and to assembly drawings of joints. NOTEFor uniformity all figures in this International Standard are drawn in the first-angle orthographic projection. It should be understood that the third-an
23、gle orthographic projection could equally well have been used without prejudice to the principles established. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, th
24、e editions indicated were valid. All standards are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the standards listed below. Members of IEC and ISO maintain registers of curren
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BSENISO64131995TECHNICALDRAWINGSREPRESENTATIONOFSPLINESANDSERRATIONS 技术 制图 花键 锯齿形 表示 PDF

链接地址:http://www.mydoc123.com/p-582044.html