BS EN 61754-8-1997 Fibre optic connector interfaces - Type CF08 connector family《光纤连接器接口 CF08型接口系列》.pdf

《BS EN 61754-8-1997 Fibre optic connector interfaces - Type CF08 connector family《光纤连接器接口 CF08型接口系列》.pdf》由会员分享，可在线阅读，更多相关《BS EN 61754-8-1997 Fibre optic connector interfaces - Type CF08 connector family《光纤连接器接口 CF08型接口系列》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 61754-8:1997 IEC 61754-8: 1996 Fibre optic connector interfaces Part 8: Type CF08 connector family ICS 33.180.20BSEN61754-8:1997 This British Standard, having been prepared under the directionof the ElectrotechnicalSector Board,was published under theauthorityof the StandardsB

2、oardand comes intoeffect on 15December1997 BSI 04-2000 ISBN 0 580 28591 X National foreword This British Standard is the English language version of EN61754-8:1997. It is identical with IEC61754-8:1997. The UK participation in its preparation was entrusted by Technical Committee EPL/86, Fibre optics

3、, to Subcommittee EPL/86/2, Interconnecting devices and passive components, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests infor

4、med; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. From 1 January 1997, all IEC publications have the number60000 added to the old number. For instance, IEC2

5、7-1 has been renumbered as IEC60027-1. For a period of time during the change over from one numbering system to the other, publications may contain identifiers from both systems. Cross-references Attention is drawn to the fact that CEN and CENELEC standards normallyinclude an annex which lists norma

6、tive references to internationalpublications with their corresponding European publications. The British Standards which implement these international or European publications may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by

7、 using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immu

8、nity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theENtitle page, pages 2 to 7 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amen

9、dment table on the inside front cover. Amendments issued since publication Amd. No. Date CommentsBSEN61754-8:1997 BSI 04-2000 i Contents Page National foreword Inside front cover Foreword 2 Text of EN61754-8 3ii blankEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 61754-8 September 1997 ICS 33.

10、180.20 English version Fibre optic connector interfaces Part8:TypeCF08connector family (IEC 61754-8:1996) Interfaces de connecteurs pour fibresoptiques Partie8:Famillesdeconnecteurs de type CF08 (CEI 61754-8:1996) Lichtwellenleiter- Steckverbinderbergnge Teil8:TypCF08Steckverbinderfamilie (IEC61754-

11、8:1996) This European Standard was approved by CENELEC on1997-07-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliogra

12、phical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of

13、 a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands,

14、 Norway, Portugal, Spain, Sweden, Switzerland and UnitedKingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1997 CENELEC All

15、rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61754-8:1997 EEN61754-8:1997 BSI 04-2000 2 Foreword The text of the International Standard IEC61754-8:1996, prepared by SC86B, Fibre optic interconnecting devices and passive components, of IECTC8

16、6, Fibre optics, was submitted to the Unique Acceptance Procedure and was approved by CENELEC as EN61754-8 on1997-07-01 without any modification. The following dates were fixed: Endorsement notice The text of the International Standard IEC61754-8:1996 was approved by CENELEC as a European Standard w

17、ithout any modification. Contents Page Foreword 2 1 Scope 3 2 Description 3 3 Interfaces 3 Figure 1 Plug connector interface 4 Figure 2 Adaptor and receptacle interfaces 6 Table 1 Dimensions of the plug connector interface 5 Table 2 Dimensions of adaptor and receptacleinterfaces 7 latest date by whi

18、ch the ENhas to be implemented atnational level by publication of an identical national standard or by endorsement (dop) 1998-06-01 latest date by which the national standards conflicting with the ENhaveto be withdrawn (dow) 1998-06-01EN61754-8:1997 BSI 04-2000 3 1 Scope This part of IEC1754 defines

19、 the standard interface dimensions for the type CF08 family of connectors. 2 Description The parent connector for the type CF08 connector family is a single-way plug connector which is characterized by a conical ferrule butting against a4mm diameter sphere or equivalent. It includes a push-pull coup

20、ling mechanism and a ferrule spring loaded in the direction of the optical axis. The plug has a single male key which may be used to orient and limit the relative rotation between the connector and the component to which it is mated. 3 Interfaces This standard contains the following standard interfa

21、ces: a) interface 8-1: plug connector interface; b) interface 8-2: adapter for plug/adapter/plug configuration; c) interface 8-3: receptacle connector for plug/receptacle/optical component configuration.EN61754-8:1997 4 BSI 04-2000 Figure 1 Plug connector interfaceEN61754-8:1997 BSI 04-2000 5 Table

22、1 Dimensions of the plug connector interface Reference Dimensions Basic Notes Reference Dimensions Basic Notes Minimum Maximum Minimum Maximum A 14,40 mm U 1,40 mm 1,50 mm C 7,02 mm 7,14 mm 1 V 4,17 mm 4,205 mm D 0 mm 0,40 mm 3 W 1,15 mm 1,29 mm E 1,50 mm 2,10 mm 1 X 1,80 mm 1,90 mm F 3,30 mm 4,50 m

23、m 1 Y 11,30 mm 11,90 mm G 12,30 mm 13,40 mm 1 Z 12,03 mm 12,50 mm H 8,30 mm 10,20 mm AB 4,42 mm 4,53 mm J 11,40 mm 11,80 mm AC 1,54 mm 1,575 mm K 6,40 mm 7,83 mm AD 30 L 5,125 mm 5,19 mm AE 89,2 90,8 M 4,975 mm 5,04 mm AF 11,2 12,8 6 N 2 mm 4,40 mm AG 0,005 mm 0,013 mm P 5,795 mm 5,86 mm AH 29,2 30,

24、8 Q 5,595 mm 5,67 mm AI 8 mm 3 R 0,80 mm 1,04 mm 2 BA 0,10 mm 0,30 mm 6 S 3,79 mm 3,90 mm BB 58 64 6 T 4 mm 5 BC 11,2 20 6 BD 0,003 mm + 0,040 mm 6 NOTE 1These dimensions are for a mated plug; the ferrule compression force is then between8N and18N. From this mated position, the ferrule can enter in

25、the plug for at least0,15mm, and for the free plug, it can get out for at least0,35mm. NOTE 245 chamfer. NOTE 3Dimensions when the latching mechanism is not active (free or mated plug). NOTE 4Datum plane containing the centre of sphere T and perpendicular to the direction defined by the centre of sp

26、here T and the centre of circle V at distance Z. NOTE 5Sphere butting on conical surface AE. NOTE 6For fibre with core diameter bigger than4004m, BA=0mm, AF=BB=BC=0 , BD=AG.EN61754-8:1997 6 BSI 04-2000 Figure 2a Figure 2b Figure 2 Adaptor and receptacle interfacesEN61754-8:1997 BSI 04-2000 7 Table 2

27、 Dimensions of adaptor and receptacle interfaces Reference Dimensions Nominal Notes Reference Dimensions Basic Notes Minimum Maximum Minimum Maximum A 13,50 mm 14,35 mm S 3,94 mm 4,24 mm B 8,20 mm 9,00 mm T 3,995 mm 4,002 mm C 7,02 mm 7,14 mm U 1,95 mm 2,20 mm E 0,60 mm 1,25 mm V 4,21 mm 4,24 mm F 0

28、,60 mm 3,05 mm W 0,65 mm 1,00 mm G 0,60 mm 12,25 mm Y 11,2 mm H 10,30 mm 10,45 mm Z 0,65 mm 12 mm K 7,87 mm AB 4,56 mm L 5,05 mm 5,115 mm AC 1,585 mm 1,63 mm M 4,90 mm 4,965 mm AD 28 mm 32 mm N 4,60 mm AF 59,5 60,5 P 5,72 mm 5,785 mm AG 0 mm 0,08 mm Q 5,52 mm 5,585 mm AJ 1,8 mm 7,14 mm R 1,06 mm 1,3

29、0 mm 5 AK 0,04 mm mm NOTE 1Limit dimensions are for terminated and mated connectors. NOTE 2Individual and related features shall be geometrically perfect at the specified limit dimensions. NOTE 3Unrelated features should be capable of taking up their basic relative location at the specified limit di

30、mensions. NOTE 4Datum plane containing the centre of the sphere T and perpendicular to the direction defined by the centre of the sphere T and the centre of circle V at the distance Z. NOTE 545 chamfer. NOTE 6Two options are possible for the adapters, mechanically and optically intermatable with the

31、 plug interface. In one option, the reference sphere has an elastomeric part definitely linked with it. The thickness and the hardness of the elastomeric material is such that there is always a physical contact between the optical faces and the elastomeric material. The other option, without elastom

32、eric, is generally used for fibre with a core diameter bigger than4004m. The receptacles never have elastomeric material in the sphere.BS EN 61754-8:1997 IEC61754-8: 1996 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for prep

33、aring BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions.

34、 It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside f

35、ront cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed

36、 to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of infor

37、mation on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:020899670

38、48. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI pu

39、blications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic

40、, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.