BS EN 61754-6-2013 Fibre optic interconnecting devices and passive components Fibre optic connector interfaces Type MU connector family《纤维光学互连器件和无源元件 纤维光学连接器接口 MU型连接器系列》.pdf

《BS EN 61754-6-2013 Fibre optic interconnecting devices and passive components Fibre optic connector interfaces Type MU connector family《纤维光学互连器件和无源元件 纤维光学连接器接口 MU型连接器系列》.pdf》由会员分享，可在线阅读，更多相关《BS EN 61754-6-2013 Fibre optic interconnecting devices and passive components Fibre optic connector interfaces Type MU connector family《纤维光学互连器件和无源元件 纤维光学连接器接口 MU型连接器系列》.pdf（82页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationFibre optic interconnecting devices and passive components Fibre optic connector interfacesPart 6: Type MU connector familyBS EN 61754-6:2013Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduct

2、ion or networking permitted without license from IHS-,-,-National forewordThis British Standard is the UK implementation of EN 61754-6:2013. It is identical to IEC 61754-6:2013. It supersedes BS EN 61754-6:1997 which is withdrawn.The UK participation in its preparation was entrusted by TechnicalComm

3、ittee GEL/86, Fibre optics, to Subcommittee GEL/86/2, Fibre opticinterconnecting devices and passive components.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions ofa contract. Use

4、rs are responsible for its correct application. The British Standards Institution 2013.Published by BSI Standards Limited 2013ISBN 978 0 580 72643 9ICS 33.180.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of

5、theStandards Policy and Strategy Committee on 31 December 2013.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 61754-6:2013Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction o

6、r networking permitted without license from IHS-,-,-EUROPEAN STANDARD EN 61754-6 NORME EUROPENNE EUROPISCHE NORM November 2013 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC

7、Management Centre: Avenue Marnix 17, B - 1000 Brussels 2013 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61754-6:2013 E ICS 33.180.20 Supersedes EN 61754-6:1997 + A1:2001 + A2:2005 English version Fibre optic interconnecting de

8、vices and passive components - Fibre optic connector interfaces - Part 6: Type MU connector family (IEC 61754-6:2013) Dispositifs dinterconnexion et composants passifs fibres optiques - Interfaces de connecteurs fibres optiques (CEI 61754-6:2013) Lichtwellenleiter - Verbindungselemente und passive B

9、auteile - Steckgesichter von Lichtwellenleiter-Steckverbindern - Teil 6: Bauart MU-Steckverbinderfamilie (IEC 61754-6:2013) This European Standard was approved by CENELEC on 2013-08-26. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for g

10、iving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in thr

11、ee official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national elec

12、trotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Ro

13、mania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 61754-6:2013Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EN 61

14、754-6:2013 - 2 - Foreword The text of document 86B/3627/FDIS, future edition 2 of IEC 61754-6, prepared by subcommittee 86B “Fibre optic interconnecting devices and passive components” of IEC/TC 86 “Fibre optics“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 61754-6:20

15、13. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2014-05-26 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2014-0

16、8-26 This document supersedes EN 61754-6:1997 + A1:2001 + A2:2005. EN 61754-6:2013 includes the following significant technical changes with respect to EN 61754-6:1997 + A1:2001 + A2:2005 : a) addition of standard references; b) revision of intermateability. Attention is drawn to the possibility tha

17、t some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 61754-6:2013 was approved by CENELEC as a European Standard witho

18、ut any modification. BS EN 61754-6:2013Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- 3 - EN 61754-6:2013 Annex ZA (normative) Normative references to inte

19、rnational publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition

20、of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 61755-3-1 Fibre optic interconnecting devices and passive components

21、-Fibre optic connector optical interfaces - Part 3-1:Connectors with 2,5 mm and 1,25 mm diameter cylindrical full zirconia ferrule, non-angled single mode non-dispersion shifted fibres prEN 61755-3-11)IEC 61755-3-2 Fibre optic interconnecting devices and passive components -Fibre optic connector opt

22、ical interfaces - Part 3-2: Connectors with 2,5 mm and 1,25 mm diameter cylindrical full zirconia ferrule, angled single mode non-dispersion shifted fibres prEN 61755-3-21)1)At draft stage. BS EN 61754-6:2013Copyright European Committee for Electrotechnical Standardization Provided by IHS under lice

23、nse with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- 2 61754-6 IEC:2013(E) CONTENTS 1 Scope . 7 2 Normative references . 7 3 Description . 7 4 Interfaces . 7 Annex A (informative) Configuration of type MU-A connector set . 74 Annex B (informative) Confi

24、guration of type MU-B connector set . 75 Annex C (informative) Floating 2-port connector plug . 76 Bibliography 77 Figure 1 Simplex plug connector interface Push/pull . 11 Figure 2 4,5 mm duplex plug connector interface Push/pull . 14 Figure 3 Simplex adaptor connector interface Push/pull 17 Figure

25、4 Gauge pin for resilient alignment sleeve . 19 Figure 5 4,5 mm duplex adaptor connector interface Push/pull 20 Figure 6 8-port adaptor connector interface Push/pull . 23 Figure 7 Plug connector interface For printed board housings . 25 Figure 8 Sleeve holder interface 27 Figure 9 2-port backplane h

26、ousing interface. 30 Figure 10 2-port printed board housing interface 34 Figure 11 8-port backplane housing interface . 37 Figure 12 8-port printed board housing interface 41 Figure 13 Simplex active device receptacle interface . 43 Figure 14 Detail of the mechanical stop for rigid bore alignment fe

27、ature. 45 Figure 15 4,5 mm duplex active device receptacle interface . 46 Figure 16 Detail of the mechanical stop for rigid bore alignment feature. 48 Figure 17 6,25 mm duplex active device receptacle interface . 49 Figure 18 Detail of the mechanical stop for rigid bore alignment feature. 51 Figure

28、19 Plug connector interface for printed board housings, APC 53 Figure 20 Simplex plug connector interface Push/pull, APC 56 Figure 21 4,5 mm duplex plug connector interface Push/pull, APC 59 Figure 22 6,25 mm duplex plug connector interface Push/pull, APC 62 Figure 23 6,25 mm duplex plug connector i

29、nterface Push/pull . 64 Figure 24 6,25 mm duplex adaptor connector interface 67 Figure 25 Horizontal duplex plug connector interface Push/pull . 69 Figure 26 Horizontal duplex adaptor connector interface 72 Figure A.1 Configuration of type MU-A connector set . 74 Figure B.1 Configuration of type MU-

30、B connector set . 75 Figure C.1 Floating 2-port connector plug 76 Table 1 MU-A connector set . 9 BS EN 61754-6:2013Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IH

31、S-,-,-61754-6 IEC:2013(E) 3 Table 2 MU-B connector set . 9 Table 3 MU receptacles . 10 Table 4 Dimensions of the simplex plug connector interface 12 Table 5 Grade 13 Table 6 Dimensions of the 4,5 mm duplex plug connector interface . 15 Table 7 Grade 16 Table 8 Dimensions of the simplex adaptor conne

32、ctor interface . 18 Table 9 Grade 18 Table 10 Gauge pin dimensions . 19 Table 11 Dimensions of the 4,5 mm duplex adaptor connector interface 21 Table 12 Grade 22 Table 13 Dimensions of the 8-port adaptor connector interface 24 Table 14 Grade 24 Table 15 Dimensions of the plug connector interface . 2

33、6 Table 16 Grade 26 Table 17 Dimensions of the sleeve holder interface . 28 Table 18 Grade 28 Table 19 Dimensions of the 2-port backplane housing interface) 31 Table 20 Grade 32 Table 21 Dimensions of the 2-port printed board housing interface 35 Table 22 Dimensions of the 8-port backplane housing i

34、nterface . 38 Table 23 Grade 39 Table 24 Dimensions of the 8-port printed board housing interface 42 Table 25 Dimensions of the simplex active device receptacle interface 44 Table 26 Alignment feature grade 45 Table 27 Dimensions of the mechanical stop for rigid bore alignment feature . 45 Table 28

35、Mechanical stop feature grade. 46 Table 29 Dimensions of the 4,5 mm duplex active device receptacle interface . 47 Table 30 Alignment feature grade 48 Table 31 Dimensions of the mechanical stop for rigid bore alignment feature . 48 Table 32 Mechanical stop feature grade. 49 Table 33 Dimensions of th

36、e 6,25 mm duplex active device receptacle interface . 50 Table 34 Alignment feature grade 51 Table 35 Dimensions of the mechanical stop for rigid bore alignment feature . 51 Table 36 Mechanical stop feature grade. 52 Table 37 Dimensions of the plug connector interface for printed board housings, APC

37、 . 54 Table 38 Dimensions of the simplex plug connector interfaces, APC 57 Table 39 Dimensions of the 4,5 mm duplex plug connector interfaces, APC . 60 Table 40 Dimensions of the 6,25 mm duplex plug connector interface, APC. 63 Table 41 Dimensions of the 6,25 mm duplex plug connector interface 65 Ta

38、ble 42 Grade 66 Table 43 Dimensions of the 6,25 mm duplex adaptor connector interface 68 Table 44 Grade 68 BS EN 61754-6:2013Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without licen

39、se from IHS-,-,- 4 61754-6 IEC:2013(E) Table 45 Dimensions of the horizontal duplex plug connector interface 70 Table 46 Grade 71 Table 47 Dimensions of the horizontal duplex adaptor connector interface . 73 Table 48 Grade 73 Table C.1 Dimensions table for 2-port connector plug 76 BS EN 61754-6:2013

40、Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-61754-6 IEC:2013(E) 7 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS FIBRE OPTIC CONNECTOR INTERF

41、ACES Part 6: Type MU connector family 1 Scope This part of IEC 61754 defines the standard interface dimensions for type MU family of connectors. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application.

42、 For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 61755-3-1, Fibre optic connector optical interfaces Part 3-1:Optical interface, 2,5 mm and 1,25 mm diameter cylindrical full zirconia P

43、C ferrule, single mode fibre IEC 61755-3-2, Fibre optic connector optical interfaces Part 3-2: Optical interface, 2,5 mm and 1,25 mm diameter cylindrical full zirconia ferrules for 8 degrees angled-PC single mode fibres 3 Description The parent connector for type MU connector family is a miniature s

44、ingle-position plug which is characterized by a cylindrical, spring-loaded butting ferrule(s) of a 1,25 mm typical diameter, and a push-pull coupling mechanism. The optical alignment mechanism of the connectors is of a rigid hole or a resilient sleeve style. This part 6 type MU connector family defi

45、nes the standard interface dimensions of active device receptacles for the type MU connectors. The receptacles are used to retain the connector plugs and mechanically maintain the optical datum target of the plugs at a defined position within the receptacle housings. 4 Interfaces This standard conta

46、ins the following standard interfaces. Interface IEC 61754-6-1: Simplex plug connector interface Push/pull (See Figure 1) Interface IEC 61754-6-2: 4,5 mm duplex plug connector interface Push/pull (See Figure 2) Interface IEC 61754-6-3: Simplex adaptor connector interface Push/pull (See Figure 3) Int

47、erface IEC 61754-6-4: 4,5 mm duplex adaptor connector interface Push/pull (see Figure 5) Interface IEC 61754-6-5: 8-port adaptor connector interface Push/pull (See Figure 6) Interface IEC 61754-6-6: Plug connector interface for printed board housings (See Figure 7) Interface IEC 61754-6-7: Sleeve ho

48、lder interface for printed board housings (See Figure 8) Interface IEC 61754-6-8: 2-port backplane housing interface Self-retentive (See Figure 9) BS EN 61754-6:2013Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- 8 61754-6 IEC:2013(