BS EN 60966-1-1999 Radio frequency and coaxial cable assemblies Generic specification General requirements and test methods《射频与同轴电缆组件 通用规范 试验方法和一般要求》.pdf

《BS EN 60966-1-1999 Radio frequency and coaxial cable assemblies Generic specification General requirements and test methods《射频与同轴电缆组件 通用规范 试验方法和一般要求》.pdf》由会员分享，可在线阅读，更多相关《BS EN 60966-1-1999 Radio frequency and coaxial cable assemblies Generic specification General requirements and test methods《射频与同轴电缆组件 通用规范 试验方法和一般要求》.pdf（44页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 60966-1:1999 IEC 60966-1: 1999 QC140000: 1999 Radio frequency and coaxial cable assemblies Part 1: Generic specification General requirements and test methods The European Standard EN 60966-1:1999 has the status of a British Standard ICS 33.120.10BSEN 60966-1:1999 This British

2、 Standard, having been prepared under the directionof the Electrotechnical Sector Committee, was publishedunder the authorityofthe Standards Committee and comes into effect on 15October1999 BSI 03-2000 ISBN 0 580 35306 0 National foreword This British Standard is the English language version of EN 6

3、0966-1:1999. It is identical with IEC 60966-1:1999. It supersedes BS EN60966-1:1993which will be withdrawn on 2002-02-01. This standard is a harmonized specification within the IEC quality assessment system for electronic components (IECQ). In the IECQ system, this specification is numbered QC 14000

4、0. The UK participation in its preparation was entrusted by Technical Committee EPL/46, Cables, wires, waveguides, RF connectors and accessories for comms and signalling, to Subcommittee EPL/46/1, Communication cables, which has the responsibility to: aid enquirers to understand the text; present to

5、 the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be o

6、btained on request to its secretary. From1January1997, all IEC publications have the number60000added to the old number. For instance, IEC27-1has been renumbered as IEC 60027-1. For a period of time during the change over from one numbering system to the other, publications may contain identifiers f

7、rom both systems. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards normally include an annex which lists normative references to international publications with their corresponding European publications. The British Standards which implement international or European pu

8、blications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary p

9、rovisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theEN title

10、page, pages 2 to 38 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date CommentsBS EN 60966-1:1999 BSI 03-2000 i Cont

11、ents Page National foreword Inside front cover Foreword 2 Text of EN 60966-1 5ii blankEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 60966-1 June 1999 ICS 33.120.10 Supersedes EN 60966-1:1993 English version Radio frequency and coaxial cable assemblies Part 1: Generic specification General req

12、uirements and test methods (IEC 60966-1:1999) Ensembles de cordons coaxiaux et decordonspour frquences radiolectriques Partie 1: Spcification gnrique Gnralits et mthodes dessai (CEI 60966-1:1999) Konfektionierte Koaxial- und Hochfrequenzkabel Teil1:Fachgrundspezifikation AllgemeineAnforderungen und

13、Prfverfahren (IEC 60966-1:1999) This European Standard was approved by CENELEC on 1999-05-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to

14、-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation un

15、der the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland,

16、 Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stas

17、sart 35, B-1050 Brussels 1999 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60966-1:1999 EEN 60966-1:1999 2 BSI 03-2000 Foreword The text of document 46A/343/FDIS, future edition2of IEC 60966-1, prepared by SC 46A, Coaxial cables,

18、 of IEC TC 46, Cables, wires, waveguides, R.F. connectors, and accessories for communication and signalling, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60966-1 on 1999-05-01. This European Standard supersedes EN 60966-1:1993. The following dates were fixed: Anne

19、xes designated “normative” are part of the body of the standard. Annexes designated “informative” are given for information only. In this standard, Annex A, Annex E and Annex ZA are normative and Annex B, Annex C and Annex D are informative. Annex ZA has been added by CENELEC. Endorsement notice The

20、 text of the International Standard IEC60966-1:1999was approved by CENELEC as a European Standard without any modification. Contents Page Foreword 2 1 Scope 5 2 Normative references 5 3 Definitions 5 4 Design and manufacturing requirements 6 4.1 Cable design and construction 6 4.2 Connector design a

21、nd construction 7 4.3 Outline and interface dimensions 7 5 Workmanship, marking and packaging 7 5.1 Workmanship 7 5.2 Marking 7 5.3 End caps 7 5.4 Packaging and labelling 7 6 Quality assessment 7 7 Test methods General 7 7.1 Standard atmospheric conditions for testing 7 7.2 Visual inspection 7 7.3 D

22、imensions inspection 7 8 Electrical tests 7 8.1 Reflection properties 7 8.2 Uniformity of impedance 8 8.3 Insertion loss 8 8.4 Insertion loss stability 8 8.5 Propagation time 9 8.6 Stability of electrical length 9 8.7 Phase difference 11 8.8 Phase variation with temperature 11 8.9 Screening effectiv

23、eness 12 8.10 Voltage proof 12 8.11 Insulation resistance 12 8.12 Inner and outer conductor continuity 12 8.13 Void 12 8.14 Power rating 12 8.15 Intermodulation level measurement 13 9 Mechanical robustness tests 13 9.1 Tensile 13 9.2 Flexure 13 9.3 Flexing endurance 14 9.4 Cable assembly crushing 14

24、 9.5 Torque 15 9.6 Multiple bending 15 9.7 Abrasion test of cable assembly 15 latest date by which the ENhas to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2000-02-01 latest date by which the national standards conflicting with the EN hav

25、eto be withdrawn (dow) 2002-05-01EN 60966-1:1999 BSI 03-2000 3 Page 9.8 Vibrations, shocks and impact 16 9.9 Mechanical endurance 16 10 Environmental tests 16 10.1 Recommended severities 16 10.2 Vibration, bumps and shock 16 10.3 Climatic sequence 16 10.4 Damp heat, steady state 16 10.5 Rapid change

26、 of temperature 16 10.6 Solvents and contaminating fluids 17 10.7 Water immersion 17 10.8 Salt mist and sulphur dioxide tests 17 10.9 Dust tests 17 10.10 Flammability 18 11 Specialized test methods 19 12 Test schedules 19 Annex A (normative) Test methods for insertionlossdetermination 20 A.1 Purpose

27、 20 A.2 Test methods 20 A.2.1 Test method 1 20 A.2.2 Test method 2 21 A.2.3 Test method 3 22 A.3 Correction for characteristic impedance differences 23 Annex B (informative) Measuring methodsforpropagation time 24 B.1 Resonance method for propagation timemeasurement 24 B.2 Time domaine method for pr

28、opagation timemeasurement 25 Annex C (informative) Measurement methodforscreening effectiveness 25 C.1 Introduction 25 C.2 Test method 26 Annex D (informative) Recommended severitiesforenvironmental tests 28 D.1 Introduction to the relationship betweenenvironmental conditions and testseverities 28 D

29、.1.1 General 28 D.1.2 Environmental conditions 28 D.1.3 Environmental testing 28 D.2 Severities for environmental testing 29 D.2.1 Vibration 29 D.2.2 Bump 30 D.2.3 Shock 30 D.2.4 Climatic sequence 30 Page D.2.5 Damp heat, steady state 30 D.2.6 Rapid change of temperature 31 D.2.7 Salt mist 31 D.2.8

30、Sulphur dioxide test 31 D.2.9 Dust test 31 Annex E (normative) Quality assessment 31 E.1 Object 31 E.2 General 31 E.2.1 Related documents 31 E.2.2 Standards and preferred values 31 E.2.3 Marking of the cable assembly and packaging 31 E.2.4 Terminology 31 E.3 Quality assessment procedures 32 E.3.1 Pr

31、ocedures for qualification approval 32 E.3.2 Procedures for capability approval 32 E.3.3 Quality conformance inspection 33 E.4 Capability manual and approval 34 E.4.1 Responsibilities 34 E.4.2 Contents of the capability manual 34 E.4.3 Criteria for capability limits 35 Annex ZA (normative) Normative

32、 references tointernational publications with their corresponding European publications 37 Figure 1 Bending test: U shape assembly 9 Figure 2 Bending test: straight assembly 10 Figure 3 Twisting test: U shape assembly 11 Figure 4 Fixture for cable assembly flexure test 13 Figure 5 Apparatus for cabl

33、e assembly flexingendurance test 14 Figure 6 Fixture for cable crushing test 14 Figure 7 Multiple bending test 15 Figure 8 Dust measuring device 18 Figure A.1 Circuit for the determination ofinsertion loss 20 Figure A.2 Circuit for the determination ofinsertion loss 21 Figure A.3 Alternative circuit

34、 for the determination of insertion loss 21 Figure A.4 Double-pass circuit for thedetermination of insertion loss 22 Figure B.1 Arrangement of test equipment 24 Figure C.1 Line injection test circuit forcoaxialcable assemblies 25 Figure C.2 Schematic transfer functions ofacoaxial cable assembly 26EN

35、 60966-1:1999 4 BSI 03-2000 Page Figure C.3 Complete installation for practicalscreening effectiveness measurements 27 Figure D.1 Description of action needed forthepreparation of the environmental testspecification 29 Table D.1 Relationship between displacementand acceleration 30 Table D.2 Relation

36、ship between peak acceleration and velocity change 30 Table E.1 Example of capability limits forcableassemblies 35 Table E.2 Example of capability limits forflexiblecables 36 Table E.3 Example of capability limits forconnectors 36 Table E.4 Example of flow chart 36EN 60966-1:1999 BSI 03-2000 5 1 Sco

37、pe This International Standard specifies requirements for radio frequency coaxial cable assemblies operating in the transverse electromagnetic mode (TEM) and establishes general requirements for testing the electrical, mechanical and environmental properties of radio frequency coaxial cable assembli

38、es composed of cables and connectors. Additional requirements relating to specific families of cable assemblies are given in the relevant sectional specifications. NOTE 1The design of the cables and connectors used should preferably conform to the applicable parts of IEC61196and IEC61169respectively

39、. NOTE 2This specification does not include tests which are normally performed on the cables and connectors separately. These tests are described in IEC61196-1and IEC61169-1respectively. NOTE 3Wherever possible, cables and connectors used in cable assemblies, even if they are not described in the IE

40、C61196or IEC61169series are tested separately according to the tests given in the relevant generic specification. NOTE 4Where additional protection is applied to a cable assembly, the mechanical and environmental tests described in this standard are applicable. 2 Normative references The following n

41、ormative documents contain provisions which, through reference in this text, constitute provisions of this part of IEC 60966. At the time of publication, the editions indicated were valid. All normative documents are subject to revision, and parties to agreements based on this part of IEC60966are en

42、couraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. IEC 60068-2-3:1969, Environmental testing Part 2: Tests Test Ca: Damp heat, steady state. IEC

43、 60068-2-6:1995, Environmental testing Part 2: Tests Test Fc: Vibration (sinusoidal). IEC 60068-2-11:1981, Environmental testing Part 2: Tests Test Ka: Salt mist. IEC 60068-2-14:1984, Environmental testing Part 2: Tests Test N: Change of temperature. IEC 60068-2-27:1987, Environmental testing Part 2

44、: Tests Test Ea and guidance: Shock. IEC 60068-2-29:1987, Environmental testing Part 2: Tests Test Eb and guidance: Bump. IEC 60068-2-42:1982, Environmental testing Part 2: Tests Test Kc: Sulphur dioxide test for contacts and connections. IEC 60068-2-68:1994, Environmental testing Part 2: Tests Test

45、 L: Dust and sand. IEC 60096-1:1986, Radio frequency cables Part1:General requirements and measuring methods. IEC 60332-1:1993, Tests on electric cables under fire conditions Part 1: Test on a single vertical insulated wire or cable. IEC 60339 (all parts), General purpose rigid coaxial transmission

46、lines and their associated flange connectors. IEC 60512-5:1992, Electromechanical components for electronic equipment, basic testing procedures and measuring methods Part 5: Impact tests (free components), static load tests (fixed components), endurance tests and overload tests. IEC 61169-1:1992, Ra

47、dio-frequency connectors Part 1: Generic specification General requirements and measuring methods. IEC 61196-1:1995, Radio-frequency cables Part1:Generic specification General definitions, requirements and test methods. IEC 61726:1995, Cable assemblies, cables, connectors and passive microwave compo

48、nents Screening attenuation measurement by the reverberation chamber method. IEC QC 001002:1986, Rules of procedure of the IEC quality assessment system for electronic components (IECQ). ISO 9000, Quality management and quality assurance standards. ISO 9001:1994, Quality systems Model for quality as

49、surance in design, development, production, installation and servicing. ISO 9002:1994, Quality systems Model for quality assurance in production, installation and servicing. 3 Definitions For the purpose of this part of IEC 60966, the following definitions apply. 3.1 cable assembly a combination of cable(s) and connector(s) with or without any additional protection and with specified performance, used as a single unit 3.1.1 flexible cable assembly