BS EN 60512-14-2-2006 Connectors for electronic equipment - Tests and measurements - Sealing tests - Test 14b - Sealing - Fine air leakage《电子设备用连接器 试验和测量 密封试验 试验14b 密封 细微的漏气》.pdf

《BS EN 60512-14-2-2006 Connectors for electronic equipment - Tests and measurements - Sealing tests - Test 14b - Sealing - Fine air leakage《电子设备用连接器 试验和测量 密封试验 试验14b 密封 细微的漏气》.pdf》由会员分享，可在线阅读，更多相关《BS EN 60512-14-2-2006 Connectors for electronic equipment - Tests and measurements - Sealing tests - Test 14b - Sealing - Fine air leakage《电子设备用连接器 试验和测量 密封试验 试验14b 密封 细微的漏气》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58measurements Part 14-2: Sealing tests Test 14b: Sealing Fine air leakageThe European Standard EN 60

2、512-14-2:2006 has the status of a British StandardICS 31.220.10Connectors for electronic equipment Tests and BRITISH STANDARDBS EN60512-14-2:2006BS EN 60512-14-2:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee on June 30 2006 BSI 2006ISBN 0

3、580 48673 7Cross-referencesThe British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Ca

4、talogue or of British Standards Online.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations.Summary of pagesThis documen

5、t comprises a front cover, an inside front cover, the EN title page, pages 2 to 6, an inside back cover and a back cover.The BSI copyright notice displayed in this document indicates when the document was last issued.Amendments issued since publicationAmd. No. Date CommentsA list of organizations re

6、presented on this committee can be obtained on request to its secretary. present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep UK interests informed; monitor related international and European developments and promulgate th

7、em in the UK.National forewordThis British Standard is the official English language version of EN 60512-14-2:2006. It is identical with IEC 60512-14-2:2006. The UK participation in its preparation was entrusted to Technical Committee EPL/48, Electromechanical components and mechanical structures fo

8、r electronic equipment, which has the responsibility to: aid enquirers to understand the text;EUROPEAN STANDARD EN 60512-14-2 NORME EUROPENNE EUROPISCHE NORM May 2006 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee f

9、r Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2006 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60512-14-2:2006 E ICS 31.220.10 English version Connectors for electronic equipment - Test

10、s and measurements Part 14-2: Sealing tests - Test 14b: Sealing - Fine air leakage (IEC 60512-14-2:2006) Connecteurs pour quipements lectroniques - Essais et mesures Partie 14-2: Essais dtanchit - Essai 14b: Etanchit - Micro-fuite dair (CEI 60512-14-2:2006) Steckverbinder fr elektronische Einrichtun

11、gen - Mess- und Prfverfahren Teil 14-2: Prfungen der Dichtheit - Prfung 14b: Dichtheit - Kleine Leckrate (IEC 60512-14-2:2006) This European Standard was approved by CENELEC on 2006-04-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions fo

12、r giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three offi

13、cial versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical comm

14、ittees of Austria, Belgium, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdo

15、m. 2 Foreword The text of document 48B/1605/FDIS, future edition 1 of IEC 60512-14-2, prepared by SC 48B, Connectors, of IEC TC 48, Electromechanical components and mechanical structures for electronic equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60512-

16、14-2 on 2006-04-01. This standard is to be read in conjunction with EN 60512-1 and EN 60512-1-100 which explains the structure of the EN 60512 series. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard

17、or by endorsement (dop) 2007-01-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2009-04-01 Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 60512-14-2:2006 was approved by CENELEC as a European Stand

18、ard without any modification. _ EN 60512-14-2:2006 3 EN 60512-14-2:2006 CONNECTORS FOR ELECTRONIC EQUIPMENT TESTS AND MEASUREMENTS Part 14-2: Sealing tests Test 14b: Sealing Fine air leakage 1 Scope and object This part of IEC 60512, when required by the detail specification, is used for testing con

19、nectors within the scope of IEC technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this part of IEC 60512 is to detail a standard test method to assess the effectiveness of seals against gas pressure differentials. NOTE The test ma

20、y be done using two test chambers; this facilitates the detection of tracer gas and operation at low barometric pressures, for example, in mountainous regions. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only

21、 the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60512-1-1, Connectors for electronic equipment Tests and measurements Part 1-1: General examination Test 1a: Visual examination 3 Terms and definitions For the pu

22、rposes of this document, the following terms and definitions apply. 3.1 gas gas is used in the generic sense and therefore includes mixtures including air. No assessment of the corrosive or other similar chemical or physical reactions between gases and material involved is intended 3.2 leakage rate

23、loss of pressure per test chamber volume with respect to time 4 Preparations 4.1 Preparation of specimen The specimen shall consist of a connector with its terminations, as given in the detail specification. It may be necessary to modify the connector in order to conduct this test. The laboratory do

24、ing so shall satisfy themselves, and so report, that any modification will not affect the validity of the test. NOTE This may, for some designs, involve irreversible alteration to the connectors. EN 60512-14-2:2006 4 44.2 Equipment The performance of this test requires the provision of chambers capa

25、ble of withstanding high vacuum and pumps capable of providing this. Laboratories shall satisfy themselves of the capabilities of such equipment used. 4.3 Lubricant or sealing substance If the detail specification so requires, the specified lubricant or sealing substance shall be applied in the mann

26、er given in the detail specification. Care shall be taken that no lubrication or sealant contains substances incompatible with the tracer gas used. 4.4 Mounting and instrumentation 4.4.1 Mounting The specimen shall be mounted on a plate forming part of a chamber that can be evacuated to provide a pr

27、essure difference of (1005) kPa between the front and rear faces of the sealing system under test. Another chamber shall surround the other side of the sealing system so that the concentration of a tracer gas may be controlled. Alternatively, the high-pressure chamber may be pressurized to achieve t

28、he same pressure differential. It is also permitted to use a combination of pressure and vacuum to the same effect. It may be that the detail specification calls for a high vacuum test. This will necessitate a high vacuum on the low-pressure side. 4.4.2 Instrumentation A leak detection means, for ex

29、ample a mass spectrometer, shall be connected to the low-pressure (vacuum) side of the system. Means of recording pressures in the chambers detailed in 4.4.1 shall be provided. 5 Method 5.1 Procedure Tracer gas, for example pure or 10 % helium or argon, shall be introduced into the high pressure cha

30、mber; any leakage shall be detected by means of a device as detailed in 4.4.2. Unless otherwise stated in the detail specification, the test shall be done at normal room temperature. NOTE 1 The method is suitable for connectors whose leakage rate is less than 1 Pacm3/s at a pressure differential of

31、100 kPa. NOTE 2 Leakage rates of less than 0,01 Pacm3/s are not considered valid unless the specimen has been ultrasonically or otherwise cleaned before testing. 5.2 Measurements 5.2.1 Initial measurements A visual examination according to IEC 60512-1-1 shall be done. There shall be no defects which

32、 would impair the validity of the test. 5 EN 60512-14-2:2006 5.2.2 Test measurements and requirements The leakage rate shall not be in excess of that given in the detail specification. NOTE In the case of the detail specification calling for no leakage, this should be taken to mean, the threshold of

33、 detection, of the apparatus used. In this case, the appropriate detail of the apparatus should be reported in any documentation supporting claims of compliance to this standard. See Clause 7. 5.2.3 Final measurements Visual examination according to IEC 60512-1-1 shall be done with 10 magnification.

34、 Any defects, which would impair the normal functioning of the connector, shall be documented. 6 Details to be specified When this test is required by a detail specification, the following shall be given therein: a) preconditioning required; b) lubricant to be applied, means and quantity; or state l

35、ubricant not required; c) if high vacuum testing is required and if so, the level of vacuum required; d) maximum permitted leakage or state no leak permitted; NOTE It should be recognised that no leak permitted means below the detection or noise level of the detection apparatus. e) any deviation fro

36、m the standard test method. 7 Documentation Any documentation supporting claims of conformance to this test shall include details of the test apparatus, resolution and accuracy of the detection means used. _ Annex ZA (normative) Normative references to international publications with their correspon

37、ding European publications The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an internati

38、onal publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60512-1-1 1)Connectors for electronic equipment - Tests and measurements Part 1-1: General examination - Test 1a: Visual examination EN 60512-1-1 20022)1)

39、Undated reference. 2)Valid edition at date of issue. EN 60512-14-2:2006 6 blankBS EN BSI389 Chiswick High RoadLondonW4 4AL60512-14-2:2006BSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe a

40、nd at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and

41、 services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offer

42、s members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44

43、 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information

44、 on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Inf

45、ormation Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administrat

46、ion. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in a

47、ll BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means e

48、lectronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.