BS EN 60317-20-2014 Specifications for particular types of winding wires Solderable polyurethane enamelled round copper wire class 155《特种绕组线规范 155级可焊接聚氨酯漆包圆铜线》.pdf

《BS EN 60317-20-2014 Specifications for particular types of winding wires Solderable polyurethane enamelled round copper wire class 155《特种绕组线规范 155级可焊接聚氨酯漆包圆铜线》.pdf》由会员分享，可在线阅读，更多相关《BS EN 60317-20-2014 Specifications for particular types of winding wires Solderable polyurethane enamelled round copper wire class 155《特种绕组线规范 155级可焊接聚氨酯漆包圆铜线》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationSpecifications for particular types of winding wiresPart 20: Solderable polyurethane enamelled round copper wire, class 155BS EN 60317-20:2014Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Not for ResaleNo reproduction or n

2、etworking permitted without license from IHS-,-,-National forewordThis British Standard is the UK implementation of EN 60317-20:2014. It isidentical to IEC 60317-20:2013. It supersedes BS EN 60317-20:1996 which iswithdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee G

3、EL/55, Winding wires.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2014.Publ

4、ished by BSI Standards Limited 2014ISBN 978 0 580 75752 5ICS 29.060.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 28 February 2014.Amendments/corrigenda issued

5、 since publicationDate Text affectedBRITISH STANDARDBS EN 60317-20:2014Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-EUROPEAN STANDARD EN 60317-20 NORME EUROPENNE E

6、UROPISCHE NORM February 2014CENELEC European Committee for Electrotechnical StandardizationComit Europen de Normalisation ElectrotechniqueEuropisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B - 1000 Brussels 2014 CENELEC - All rights of exploitation in a

7、ny form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60317-20:2014 E ICS 29.060.10 Supersedes EN 60317-20:1995 + A1:1998 + A2:2000 English version Specifications for particular types of winding wires - Part 20: Solderable polyurethane enamelled round copper wire, class 155(IE

8、C 60317-20:2013) Spcifications pour types particuliers defils de bobinage - Partie 20: Fil brasable de section circulaireen cuivre maill avec polyurthane,classe 155 (CEI 60317-20:2013) Technische Lieferbedingungen frbestimmte Typen von Wickeldrhten - Teil 20: Runddrhte aus Kupfer,verzinnbar, lackiso

9、liert mit Polyurethan,Klasse 155 (IEC 60317-20:2013) This European Standard was approved by CENELEC on 2013-11-14. CENELEC members are bound to complywith the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standardthe status of a national standard without an

10、y alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained onapplication to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any otherlang

11、uage made by translation under the responsibility of a CENELEC member into its own language and notifiedto the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,the C

12、zech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Ki

13、ngdom. Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-Foreword The text of document 55/1411/FDIS, future edition 3 of IEC 60317-20, prepared by IEC/TC 55 “Winding wi

14、res“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 60317-20:2014. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2014-08-14 latest date by

15、 which the national standards conflicting with the document have to be withdrawn (dow) 2016-11-14 This document supersedes EN 60317-20:1995. EN 60317-20:2014 includes the following significant technical changes with respect to EN 60317-20:1995: new 3.2.2 containing general notes on winding wire, for

16、merly a part of the scope; revision to references to EN 60317-0-1:2014 to clarify that their application is normative; modification to Clause 15 to remove specific wire specimen sizes; consolidation of 17.1 and 17.2 of the solderability requirements; modification to Clause 19, Dielectric dissipation

17、 factor; new Clause 23, Pin hole test. The numbering of clauses in this standard is not continuous from Clauses 20 and 30 in order to reserve space for possible future wire requirements prior to those for wire packaging. Attention is drawn to the possibility that some of the elements of this documen

18、t may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 60317-20:2013 was approved by CENELEC as a European Standard without any modification. In the official

19、version, for Bibliography, the following notes have to be added for the standards indicated: IEC 60264 Series NOTE Harmonized as EN 60264 Series (not modified). IEC 60317 Series NOTE Harmonized as EN 60317 Series (not modified). IEC 60851 Series NOTE Harmonized as EN 60851 Series (not modified). BS

20、EN 60317-20:2014 EN 60317-20:2014Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-Annex ZA (normative) Normative references to international publications with their co

21、rresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (includin

22、g any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60317-0-1 2013 Specifications for particular types of winding wires - Part 0-1: General requirements - En

23、amelled round copper wire EN 60317-0-1 2014 BS EN 60317-20:2014 EN 60317-20:2014Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Not for ResaleNo reproduction or networking permitted without license from IHS-,-,- 2 60317-20 IEC:2013 CONTENTS INTRODUC

24、TION . 5 1 Scope . 6 2 Normative references . 6 3 Terms, definitions, general notes and appearance 6 3.1 Terms and definitions 6 3.2 General notes 6 3.2.1 Methods of test 6 3.2.2 Winding wire 6 3.3 Appearance . 7 4 Dimensions 7 5 Electrical resistance . 7 6 Elongation 7 7 Springiness 7 8 Flexibility

25、 and adherence 7 9 Heat shock . 7 10 Cut-through 7 11 Resistance to abrasion (nominal conductor diameters from 0,250 mm up to and including 0,800 mm) . 7 12 Resistance to solvents 8 13 Breakdown voltage . 8 14 Continuity of insulation . 8 15 Temperature index . 8 16 Resistance to refrigerants . 8 17

26、 Solderability . 8 17.1 Nominal conductor diameters up to and including 0,100 mm 8 17.2 Nominal conductor diameters over 0,100 mm 9 18 Heat or solvent bonding 9 19 Dielectric dissipation factor . 9 20 Resistance to transformer oil 9 21 Loss of mass 9 23 Pin hole test . 9 30 Packaging 9 Bibliography

27、10 Table 1 Resistance to abrasion 8 BS EN 60317-20:2014 EN 60317-20:2014Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-60317-20 IEC:2013 5 INTRODUCTION This part of

28、IEC 60317 is one of a series which deals with insulated wires used for windings in electrical equipment. The series has three groups describing: 1) Winding wires Test methods (IEC 60851); 2) Specifications for particular types of winding wires (IEC 60317); 3) Packaging of winding wires (IEC 60264).

29、BS EN 60317-20:2014 EN 60317-20:2014Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Not for ResaleNo reproduction or networking permitted without license from IHS-,-,- 6 60317-20 IEC:2013 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES Part 20:

30、 Solderable polyurethane enamelled round copper wire, class 155 1 Scope This part of IEC 60317 specifies the requirements of solderable enamelled round copper winding wire of class 155 with a sole coating based on polyurethane resin, which may be modified providing it retains the chemical identity o

31、f the original resin and meets all specified wire requirements. NOTE A modified resin is a resin that has undergone a chemical change, or contains one or more additives to enhance certain performance or application characteristics. The range of nominal conductor diameters covered by this standard is

32、: Grade 1: 0,018 mm up to and including 0,800 mm; Grade 2: 0,020 mm up to and including 0,800 mm. The nominal conductor diameters are specified in Clause 4 of IEC 60317-0-1:2013. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are

33、indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60317-0-1:2013, Specifications for particular types of winding wires Part 0-1: General requirements E

34、namelled round copper wire 3 Terms, definitions, general notes and appearance 3.1 Terms and definitions Subclause 3.1 of IEC 60317-0-1:2013 applies. 3.2 General notes 3.2.1 Methods of test Subclause 3.2.1 of IEC 60317-0-1:2013 applies. In case of inconsistencies between IEC 60317-0-1:2013 and this p

35、art of IEC 60317, the latter shall prevail. 3.2.2 Winding wire Class 155 is a thermal class that requires a minimum temperature index of 155 and a heat shock temperature of at least 175 C. The temperature in degrees Celsius corresponding to the temperature index is not necessarily that at which it i

36、s recommended that the wire be operated and this will depend on many factors, including the type of equipment involved. BS EN 60317-20:2014 EN 60317-20:2014Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Not for ResaleNo reproduction or networking p

37、ermitted without license from IHS-,-,-60317-20 IEC:2013 7 3.3 Appearance Subclause 3.3 of IEC 60317-0-1:2013 applies. 4 Dimensions Clause 4 of IEC 60317-0-1:2013 applies. 5 Electrical resistance Clause 5 of IEC 60317-0-1:2013 applies. 6 Elongation Clause 6 of IEC 60317-0-1:2013 applies. 7 Springines

38、s Clause 7 of IEC 60317-0-1:2013 applies. 8 Flexibility and adherence Clause 8 of IEC 60317-0-1:2013 applies. 9 Heat shock Clause 9 of IEC 60317-0-1:2013 applies. The minimum heat shock temperature shall be 175 C. 10 Cut-through No failure shall occur within 2 min at 200 C. 11 Resistance to abrasion

39、 (nominal conductor diameters from 0,250 mm up to and including 0,800 mm) The wire shall meet the requirements given in Table 1. For intermediate nominal conductor diameters, the value of the next larger nominal conductor diameter shall be taken. BS EN 60317-20:2014 EN 60317-20:2014Copyright British

40、 Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Not for ResaleNo reproduction or networking permitted without license from IHS-,-,- 8 60317-20 IEC:2013 Table 1 Resistance to abrasion Nominal conductor diameter Grade 1 Grade 2 Minimum average force to failure Minimum

41、 force to failure of each measurement Minimum average force to failure Minimum force to failure of each measurement mm N N N N 0,250 2,30 1,95 4,10 3,50 0,280 2,50 2,10 4,40 3,70 0,315 2,70 2,30 4,75 4,00 0,355 2,90 2,50 5,10 4,30 0,400 3,15 2,70 5,45 4,60 0,450 3,40 2,90 5,80 4,90 0,500 3,65 3,10 6

42、,20 5,25 0,560 3,90 3,30 6,65 5,60 0,630 4,20 3,55 7,10 6,00 0,710 4,50 3,80 7,60 6,45 0,800 4,80 4,10 8,10 6,90 12 Resistance to solvents Clause 12 of IEC 60317-0-1:2013 applies. 13 Breakdown voltage Clause 13 of IEC 60317-0-1:2013 applies. The elevated temperature shall be 155 C. 14 Continuity of

43、insulation Clause 14 of IEC 60317-0-1:2013 applies. 15 Temperature index Clause 15 of IEC 60317-0-1:2013 applies. The minimum temperature index shall be 155. 16 Resistance to refrigerants Test inappropriate. 17 Solderability 17.1 Nominal conductor diameters up to and including 0,100 mm The temperatu

44、re of the solder bath shall be (390 5) C. The maximum immersion time shall be 2 s. BS EN 60317-20:2014 EN 60317-20:2014Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Not for ResaleNo reproduction or networking permitted without license from IHS-,-,

45、-60317-20 IEC:2013 9 The surface of the tinned wire shall be smooth and free from holes and enamel residues. 17.2 Nominal conductor diameters over 0,100 mm The temperature of the solder bath shall be (390 5) C. The maximum immersion time (in seconds) shall be the following multiple of the nominal co

46、nductor diameter (in millimetres) with a minimum of 2 s. Grade 1 Grade 2 8 s/mm 12 s/mm The surface of the tinned wire shall be smooth and free from holes and enamel residues. 18 Heat or solvent bonding Test inappropriate. 19 Dielectric dissipation factor Test to be agreed between purchaser and supp

47、lier. 20 Resistance to transformer oil Test inappropriate. 21 Loss of mass Test inappropriate. 23 Pin hole test Clause 23 of IEC 60317-0-1:2013 applies. 30 Packaging Clause 30 of IEC 60317-0-1:2013 applies. BS EN 60317-20:2014 EN 60317-20:2014Copyright British Standards Institution Provided by IHS u

48、nder license with BSI - Uncontrolled Copy Not for ResaleNo reproduction or networking permitted without license from IHS-,-,- 10 60317-20 IEC:2013 Bibliography IEC 60264 (all parts), Packaging of winding wires IEC 60317 (all parts), Specifications for particular types of winding wires IEC 60851 (all parts), Winding wires Test methods _ BS EN 60317-20:2014 EN 60317-20:2014Copyright British Standards Institution Provided by IHS under license with BSI - Unc