BS EN 27023-1993 Packaging - Sacks - Method of sampling empty sacks for testing《包装袋 检验用空袋取样方法》.pdf

《BS EN 27023-1993 Packaging - Sacks - Method of sampling empty sacks for testing《包装袋 检验用空袋取样方法》.pdf》由会员分享，可在线阅读，更多相关《BS EN 27023-1993 Packaging - Sacks - Method of sampling empty sacks for testing《包装袋 检验用空袋取样方法》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 27023:1993 ISO 7023:1983 Packaging Sacks Method of sampling empty sacks for testing The European Standard EN 27023:1992 has the status of a British Standard UDC 621.798.151:620.113BSEN27023:1993 This British Standard, having been prepared under the directionof the Packaging an

2、d Freight Containers Standards Policy Committee, was publishedunder the authority ofthe Standards Board and comesinto effect on 15February1993 BSI 10-1999 The following BSI references relate to the work on this standard: Committee reference PKM/11 Draft for comment 82/61042 DC ISBN 0 580 21401 X Coo

3、perating organizations The European Committee for Standardization (CEN), under whose supervision this European Standard was prepared, comprises the national standards organizations of the following countries: Austria Oesterreichisches Normungsinstitut Belgium Institut belge de normalisation Denmark

4、Dansk Standardiseringsraad Finland Suomen Standardisoimisliito, r.y. France Association franaise de normalisation Germany Deutsches Institut fr Normung e.V. Greece Hellenic Organization for Standardization Iceland Technological Institute of Iceland Ireland National Standards Authority of Ireland Ita

5、ly Ente Nazionale Italiano di Unificazione Luxembourg Inspection du Travail et des Mines Netherlands Nederlands Normalisatie-instituut Norway Norges Standardiseringsforbund Portugal Instituto Portugus da Qualidade Spain Asociacin Espaola de Normalizacin y Certificacin Sweden Standardiseringskommissi

6、onen i Sverige Switzerland Association suisse de normalisation United Kingdom British Standards Institution Amendments issued since publication Amd. No. Date CommentsBSEN27023:1993 BSI 10-1999 i Contents Page Cooperating organizations Inside front cover National foreword ii Foreword 2 1 Scope and fi

7、eld of application 3 2 References 3 3 Definitions 3 4 Principle 3 5 Procedure 3 6 Additional requirements 4 7 Test report 4 National annex NA (informative) Committees responsible Inside back cover National annex NB (informative) Cross-references Inside back cover Table 1 3 Table 2 4BSEN27023:1993 ii

8、 BSI 10-1999 National foreword This British Standard has been prepared under the direction of the Packaging and Freight Containers Standards Policy Committee and is the English language version of EN27023:1992 Packaging Sacks Method of sampling empty sacks for testing published by the European Commi

9、ttee for Standardization (CEN), which endorses ISO7023:1983, published by the International Organization for Standardization (ISO). This British Standard constitutes a new edition of BS6428:1983 Method for sampling empty sacks for testing which is withdrawn; BS6428:1983 was also identical to ISO7023

10、. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprise

11、s a front cover, an inside front cover, pages i and ii, the EN title page, pages2to4, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.EUROPEAN

12、STANDARD NORME EUROPENNE EUROPISCHE NORM EN 27023 November 1992 UDC 621.798.151:620.113 Descriptors: Packing, bags, sampling, tests English version Packaging Sacks Method of sampling empty sacksfortesting (ISO 7023:1983) Emballages Sacs Mthode dchantillonnage de sacs vides pour essais (ISO 7023:1983

13、) Packmittel Scke Verfahren zur Probenahme leerer Scke fr die Prfung (ISO 7023:1983) This European Standard was approved by CEN on1992-10-30. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a nat

14、ional standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in a

15、ny other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Ice

16、land, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1992 Copyright reserved to

17、 CEN members Ref. No. EN 27023:1992 EEN27023:1992 BSI 10-1999 2 Foreword In1991, ISO7023:1983 “Packaging Sacks Method of sampling empty sacks for testing” was submitted to the CEN Primary Questionnaire procedure. Following the positive result of the CEN/CS Proposal ISO7023:1983 is submitted to the F

18、ormal Vote. The result of the Formal Vote was positive. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May1993, and conflicting national standards shall be withdrawn at the latest by May1993. Acc

19、ording to the CEN/CENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EN2702

20、3:1992 BSI 10-1999 3 1 Scope and field of application This International Standard specifies a method of obtaining a representative sample of empty sacks for testing. This International Standard is applicable when sampling in order to assess the average quality of a consignment of empty sacks. The me

21、thod is not suited to sampling for production control. The method applies to all types of empty sacks. NOTEIt should be noted that the sample is representative only of those sacks available for sampling. Considerable caution should be exercised when extrapolating the results from such sampling to a

22、larger consignment. 2 References ISO 186, Paper and board Sampling for testing. ISO 3951, Sampling procedures and charts for inspection by variables for percent defective. 3 Definitions For the purpose of this International Standard, the following definitions apply. 3.1 lot the aggregate of sacks wh

23、ich are of a single kind with specified characteristics, on which a judgement is desired (usually as to compliance with specification) and which are available for sampling NOTE 1The number of sacks comprising a lot may be indicated on the invoice or agreed upon by the contracting parties. NOTE 2When

24、 the number of sacks available for sampling is less than the lot size agreed or indicated on the invoice, the total number of sacks available may be taken as a lot subject to the caution given in the note toclause1. 3.2 unit the unit may be in the form of a bundle, bale, pallet load, container load,

25、 etc. One or more nominally identical units constitute a lot 3.3 element the element may be in the form of a bundle, bale, pallet load etc., but cannot be a single sack. One or more nominally identical elements constitute a unit 3.4 sample a specified number of sacks selected according to a prescrib

26、ed procedure to represent the lot 3.5 selected at random taken in such a way that each part of the whole has an equal chance of being selected 4 Principle Selection at random of a prescribed number of sacks from the lot following a two-stage procedure as follows: a) Selection of a prescribed number

27、of units from the lot (see5.1). b) Use of one of the following two procedures: 1) Where the unit is not subdivided into elements, selection of a prescribed number of sacks from each of these units (see5.2.1). 2) Where the unit is subdivided into elements, selection of a prescribed number of elements

28、 from each of these units, then selection of a prescribed number of sacks from these elements (see5.2.2). 5 Procedure 5.1 Selection of units Determine and select the number of units to be sampled, according to Table 1. NOTETable 1 has been taken from ISO186. Table 1 The units selected shall be intac

29、t and in good external condition. 5.2 Selection of sacks For each unit selected from the lot, proceed as follows: 5.2.1 When the unit is not subdivided into elements Take at random an equal number of sacks from each unit so that the total number taken from the lot is not less than the number of sack

30、s required for testing and conforms to the requirements ofTable 2. NOTERelevant information forTable 2 has been extracted from the first two columns in both TablesI-A and II-A of ISO3951. Number of units (n) in the lot Number of units selected Method of selection 1 to5 all 6 to99 5 at random 100 to

31、399 a at random 400 or more 20 at random a In deciding the number of units to be selected, any remainder of less than 20 units shall be ignored. n 20 -EN27023:1992 4 BSI 10-1999 Table 2 5.2.2 When the unit is subdivided into elements If there are20or more elements in each unit, assemble all the elem

32、ents in the selected units and, usingTable 1, select the elements in the same way that the units were selected. If there are less than20elements in each unit, select one element at random from each unit. At least one element should be selected from each unit. Finally, take at random an equal number

33、of sacks from each element selected so that the total number taken from the lot is not less than the number of sacks required for testing and conforms to the requirements of Table 2. 6 Additional requirements 6.1 Precautions The sacks selected shall be kept and handled so that there is no permanent

34、change in their properties before testing. 6.2 Marking Each sack that has been selected shall have adequate identification marks to prove its origin. 6.3 Re-sampling 6.3.1 If, as a result of an accident during sampling or testing, re-sampling is necessary, a new sample shall be taken, following the

35、above procedure. Selection may then, however, be made from the same units as before unless agreed otherwise. 6.3.2 If re-sampling is needed for any other reason, the procedure adopted should follow this specification as closely as possible. 7 Test report The report shall indicate the following parti

36、culars: a) a reference to this International Standard; b) the names and addresses of the purchaser and vendor; c) the date and place of sampling; d) the description of the lot; e) the number of units in the lot; f) the number of units selected; g) the number of elements, if any, in a unit; h) the nu

37、mber of elements selected; j) the number of sacks in the lot; k) the number of sacks selected; m) any circumstances which might influence the results of future tests; n) a reference corresponding to the identification marks on the sacks; p) the signature of the person carrying out the sampling; q) a

38、ny deviation from this International Standard. Number of sacks in the lot Minimum number of sacks to be taken from the lot Not more then280 3 281 to500 4 501 to1 200 5 1 201 to3 200 7 3 201 to 10 000 10 10 001 to 35 000 15 More then 35 000 20BSEN27023:1992 BSI 10-1999 National annex NA (informative)

39、 Committees responsible The United Kingdom participation in the preparation of this European Standard was entrusted by the Packaging and Freight Containers Standards Policy Committee (PKM/-) to Technical Committee PKM/11 upon which the following bodies were represented: Aluminium Federation Associat

40、ion of the British Pharmaceutical Industry British Aerosol Manufacturers Association British Paper and Board Industry Federation British Plastics Federation Coated Paper and Board Makers Association Department of Health Department of Trade and Industry (Laboratory of the Government Chemist) Flexible

41、 Packaging Association Food and Drink Federation Her Majestys Stationery Office Institute of Purchasing and Supply Packaging and Industrial Films Association Pira International Retail Bag Manufacturers Association Sterilization Packaging Materials Association The following bodies were also represent

42、ed in the drafting of the standard, through subcommittees and panels: British Cement Association British Polyolefin Textiles Association Chemical Industries Association Jute Sack and Bag Manufacturers Association National Farmers Union Paper Sack Development Association Ltd. Potato Marketing Board U

43、nited Kingdom Jute Goods Association United Kingdom Sugar Industry Association National annex NB (informative) Cross-references Publication referred to Corresponding British Standard ISO 187 BS 3431:1973 Method for the conditioning of paper and board for testing ISO 3951 BS 6002:1979 Specification f

44、or sampling procedures and charts for inspection by variables for percent defectiveBS EN 27023:1993 ISO 7023:1983 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standa

45、rds in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of

46、our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers

47、members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001.

48、In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards

49、through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright su