BS EN 14634-2010 Glass packaging 26 H 180 crown finish Dimensions《玻璃封装 26 H 180冠形瓶口 尺寸规格》.pdf

《BS EN 14634-2010 Glass packaging 26 H 180 crown finish Dimensions《玻璃封装 26 H 180冠形瓶口 尺寸规格》.pdf》由会员分享，可在线阅读，更多相关《BS EN 14634-2010 Glass packaging 26 H 180 crown finish Dimensions《玻璃封装 26 H 180冠形瓶口 尺寸规格》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 14634:2010ICS 55.100NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDGlass packaging 26H 180 crown finish DimensionsLicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 29/11/2010 07:37, Uncontrolled Copy, (c) BSIThis British Standardwas published under t

2、heauthority of the StandardsPolicy and StrategyCommittee on 30 June2010 BSI 2010ISBN 978 0 580 65728 3Amendments/corrigenda issued since publicationDate CommentsBS EN 14634:2010National forewordThis British Standard is the UK implementation of EN 14634:2010. Itsupersedes BS EN 14634:2006 which is wi

3、thdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee PKW/0/-/7, Packaging - Glass.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Us

4、ers are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 29/11/2010 07:37, Uncontrolled Copy, (c) BSIBS EN 14634:2010EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1463

5、4 June 2010 ICS 55.100 Supersedes EN 14634:2004English Version Glass packaging - 26 H 180 crown finish - Dimensions Emballage en verre - Bague couronne 26 H 180 - Dimensions Verpackungen aus Glas - Kronenmundstck 26 H 180 - Mae This European Standard was approved by CEN on 5 May 2010. CEN members ar

6、e bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to

7、the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the sam

8、e status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Po

9、rtugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any mea

10、ns reserved worldwide for CEN national Members. Ref. No. EN 14634:2010: ELicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 29/11/2010 07:37, Uncontrolled Copy, (c) BSIBS EN 14634:2010EN 14634:2010 (E) 2 Contents Page Foreword 3Introduction .41 Scope 52 Normative references 53 Dimensions .5Bibli

11、ography . 10Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 29/11/2010 07:37, Uncontrolled Copy, (c) BSIBS EN 14634:2010EN 14634:2010 (E) 3 Foreword This document (EN 14634:2010) has been prepared by Technical Committee CEN/TC 261 “Packaging”, the secretariat of which is held by AFNOR. This E

12、uropean Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2010, and conflicting national standards shall be withdrawn at the latest by December 2010. Attention is drawn to the possibility that some of th

13、e elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 14634:2004. The main technical change from the previous edition is the introduction of a new figure related to

14、the Point “P“. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, I

15、celand, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 29/11/2010 07:37, Uncontrolled Copy, (c) BSIBS EN 14634:2010EN 1

16、4634:2010 (E) 4 Introduction This document is based on CE.T.I.E. (International Technical Centre for Bottling and related Packaging) data sheet GME 13.01 Revision 1 (2007) 1. Efficient packaging is of great importance for the distribution and the protection of goods. Insufficient or inappropriate pa

17、ckaging can lead to damage or wastage of the contents of the pack. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 29/11/2010 07:37, Uncontrolled Copy, (c) BSIBS EN 14634:2010EN 14634:2010 (E) 5 1 Scope This European Standard specifies the dimensions of the 26 mm tall crown finish for glass b

18、ottles containing beverages. The tall crown finish is designed to use a metal crown closure (see CE.T.I.E. data sheet EC1-02 revision 1 2). 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited a

19、pplies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 9058, Glass containers Standard tolerances for bottles 3 Dimensions The design and dimensions of the finish shall be as shown in Figures 1, 2, 3, 4 and 5. Details which are not speci

20、fied shall be selected in accordance with the application. For general tolerances see ISO 9058. Dimensions in millimetres minimum through bore 15,5 Key a between 18,0 max and 16,5 min measured at 3 mm max down from the top Figure 1 Shoulder and bore dimensions A controlled bore of 16,6 to 15,6 measu

21、red between 1,5 and 3,0 from the top is recommended for bottles which are to be resealed and/or for sterilisation. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 29/11/2010 07:37, Uncontrolled Copy, (c) BSIBS EN 14634:2010EN 14634:2010 (E) 6 Dimensions in millimetres Key a Nominal diameter t

22、o suit glass manufacturer. b Detail X: see Figures 4 and 5 c Top of the finish Figure 2 Profile of the finish Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 29/11/2010 07:37, Uncontrolled Copy, (c) BSIBS EN 14634:2010EN 14634:2010 (E) 7 Dimensions in millimetres Key a For optimum performance

23、, the radius should lie between 0,5 and 0,8 excluding the vertical mould joint, and be as near as possible to 0,5. Figure 3 Point “P“ Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 29/11/2010 07:37, Uncontrolled Copy, (c) BSIBS EN 14634:2010EN 14634:2010 (E) 8 Dimensions in millimetres Key a

24、 Mould parting line of glass finish b Flat c Glass sealing surface d For a non returnable (“one way“) bottle, this diameter may be at 18,5 mm max, subject to written agreement through the bottler between the three involved parties (bottler, glass manufacturer, crown cork manufacturer). Figure 4 Deta

25、il X Glass sealing surface Alternative 1 Contact between the crown cork liner compound and the internal mould parting line of glass finish should be avoided (see CE.T.I.E. data sheets EC1-02 revision 1 2 and EC1-021 3). The glass sealing surface should be smooth and free of any defects. Licensed Cop

26、y: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 29/11/2010 07:37, Uncontrolled Copy, (c) BSIBS EN 14634:2010EN 14634:2010 (E) 9 Dimensions in millimetres Key a Mould parting line of glass finish b Flat c Glass sealing surface d For a non returnable (“one way“) bottle, this diameter may be at 18,5 mm max,

27、 subject to written agreement through the bottler between the three involved parties (bottler, glass manufacturer, crown cork manufacturer). Figure 5 Detail X Glass sealing surface Alternative 2 Contact between the crown cork liner compound and the internal mould parting line of glass finish should

28、be avoided (see CE.T.I.E. data sheets EC1-02 revision 1 2 and EC1-021 3). The glass sealing surface should be smooth and free of any defects. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 29/11/2010 07:37, Uncontrolled Copy, (c) BSIBS EN 14634:2010EN 14634:2010 (E) 10 Bibliography 1 CE.T.I.

29、E. data sheet GME 13.01 Revision 1, 26 H 180 Crown finish 1)2 CE.T.I.E. EC1-02 revision 1, 26 millimetres crown cork 1)3 CE.T.I.E. EC1-021, 26 millimetres crown cork: main liner profiles 1)1) Obtainable through Centre Technique International de lEmbouteillage (CE.T.I.E.), 112-114, rue La Botie, 7500

30、8 Paris, France www.cetie.org, TP: 0033-1-42 65 26 45, TF: 0033-1-40 07 03 21 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 29/11/2010 07:37, Uncontrolled Copy, (c) BSIBS EN 14634:2010This page has been intentionally left blankLicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 29/11/201

31、0 07:37, Uncontrolled Copy, (c) BSIBS EN14634:2010BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standa

32、rds in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments oreditions.It is the constant aim of BSI to improve the quality of our

33、products and services.We would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity of which can be found on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.B

34、SI offers members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fa

35、x: +44 (0)20 89967001 Email: You may also buy directly using a debit/creditcard from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply theBSI implementation of those that have been published as British Standards,unless otherwise requested.

36、Information on standardsBSI provides a wide range of information on national, European andinternational standards through its Library and its Technical Help to ExportersService. Various BSI electronic information services are also available whichgive details on all its products and services. Contact

37、 Information Centre. Tel:+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developmentsand receive substantial discounts on the purchase price of standards. For detailsof these and other benefits contact Membership Administration. Tel:

38、+44 (0)208996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British StandardsOnline can be found at http:/ information about BSI is available on the BSI website at http:/.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyr

39、ight, in theUK, of the publications of the international standardization bodies. Except aspermitted under the Copyright, Designs and Patents Act 1988 no extract maybe reproduced, stored in a retrieval system or transmitted in any form or by anymeans electronic, photocopying, recording or otherwise w

40、ithout prior writtenpermission from BSI.This does not preclude the free use, in the course of implementing the standard,of necessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then theprior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright and Licensing Manager.Tel: +44 (0)20 8996 7070 Email: Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 29/11/2010 07:37, Uncontrolled Copy, (c) BSI