EN 16287-2-2014 en Glass packaging - Screw finishes for pressure capsules - Part 2 One way glass MCA 1 finish《玻璃封装 用螺丝封口的压力胶囊 第2部分 单向MAC 1完成》.pdf
《EN 16287-2-2014 en Glass packaging - Screw finishes for pressure capsules - Part 2 One way glass MCA 1 finish《玻璃封装 用螺丝封口的压力胶囊 第2部分 单向MAC 1完成》.pdf》由会员分享,可在线阅读,更多相关《EN 16287-2-2014 en Glass packaging - Screw finishes for pressure capsules - Part 2 One way glass MCA 1 finish《玻璃封装 用螺丝封口的压力胶囊 第2部分 单向MAC 1完成》.pdf(14页珍藏版)》请在麦多课文档分享上搜索。
1、BSI Standards PublicationBS EN 16287-2:2014Glass packaging Screw finishes for pressure capsulesPart 2: One way glass MCA 1 finishBS EN 16287-2:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 16287-2:2014. The UK participation in its preparation was entruste
2、d to TechnicalCommittee PKW/0/-/7, Packaging - Glass.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The Briti
3、sh Standards Institution 2014.Published by BSI Standards Limited 2014ISBN 978 0 580 82975 8 ICS 55.100 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 May 201
4、4.Amendments issued since publicationDate Text affectedBS EN 16287-2:2014EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORMEN 16287-2 March 2014 ICS 55.100English Version Glass packaging - Screw finishes for pressure capsules - Part 2: One way glass MCA 1 finish Emballage en verre - Bagues vis pour c
5、apsules pression - Partie 2: Bague MCA 1 pour verre perdu Verpackungen aus Glas - Schraubmundstcke fr Flaschen mit Innendruck - Teil 2: Einweg-MCA 1-(Glas-)Mundstck This European Standard was approved by CEN on 12 January 2014. CEN members are bound to comply with the CEN/CENELEC Internal Regulation
6、s which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. Thi
7、s European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN memb
8、ers are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portuga
9、l, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights of exploitation in any form
10、 and by any means reserved worldwide for CEN national Members. Ref. No. EN 16287-2:2014 EBS EN 16287-2:2014EN 16287-2:2014 (E)2 ContentsPageForeword3 Introduction .4 1 Scope 5 2 Terms and definitions .5 3 Dimensions.5 Bibliography . 10 BS EN 16287-2:2014EN 16287-2:2014 (E)3 ForewordThis document (EN
11、 16287-2:2014) has been prepared by Technical Committee CEN/TC 261 “Packaging”, the secretariat of which is held by AFNOR.This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2014 and conflic
12、ting national standards shall be withdrawn at the latest by September 2014.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights.EN 16287, Gl
13、ass packaging Screw finishes for pressure capsules, consists of the following parts: Part 1: Returnable glass MCA 1 finish Part 2: One way glass MCA 1 finishAccording to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this
14、European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia,
15、 Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.BS EN 16287-2:2014EN 16287-2:2014 (E)4 IntroductionThis European Standard is based on CE.T.I.E. (International Technical Centre for Bottling and related Packaging) data sheet GME 32.05.1 Efficient packaging is of great importance f
16、or the distribution and the protection of goods. Insufficient or inappropriate packaging can lead to damage or wastage of the contents of the pack.BS EN 16287-2:2014EN 16287-2:2014 (E)5 1 ScopeThis European Standard specifies the dimensions of the 28 mm screw finish for glass containers designated M
17、CA 1 for one way glass.2 Terms and definitionsFor the purposes of this document, the following term and definition applies.2.1MCA(glass) finish designed for the closure of pressurized or vacuum liquids with a tamper-evident closure (metal or plastic)3 DimensionsThe design and dimensions of the finis
18、h shall be as shown in Table 1 and Figure 1, Figure 2, Figure 3,Figure 4 and Figure 5. Table 1 Design and dimensions of the finishPitch TPI cutter3,175 mm 2 12 8 12,5 mm = Helix angle or angle or fixture to cutter.NOTE TPI = Threads per Inch. One inch is equal to 25,4 mm.The Tan of helix angle for c
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- EN1628722014ENGLASSPACKAGINGSCREWFINISHESFORPRESSURECAPSULESPART2ONEWAYGLASSMCA1FINISH 玻璃封装 螺丝 封口 压力
链接地址:http://www.mydoc123.com/p-715751.html