BS EN 13969-2005 Flexible sheets for waterproofing - Bitumen damp proof sheets including bitumen basement tanking sheets - Definitions and characteristics《防水用柔性薄板 包括沥青底层制箱用薄板的沥青防潮薄.pdf

《BS EN 13969-2005 Flexible sheets for waterproofing - Bitumen damp proof sheets including bitumen basement tanking sheets - Definitions and characteristics《防水用柔性薄板 包括沥青底层制箱用薄板的沥青防潮薄.pdf》由会员分享，可在线阅读，更多相关《BS EN 13969-2005 Flexible sheets for waterproofing - Bitumen damp proof sheets including bitumen basement tanking sheets - Definitions and characteristics《防水用柔性薄板 包括沥青底层制箱用薄板的沥青防潮薄.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58sheets including bitumen basement tanking sheets Definitions and characteristicsThe European Standa

2、rd EN 13969:2004, incorporating amendment A1:2006, has the status of a British StandardICS 01.040.91; 91.100.50Flexible sheets for waterproofing Bitumen damp proof BRITISH STANDARDBS EN 13969:2004Incorporating amendment no. 1BS EN 13969:2004This British Standard was published under the authority of

3、the Standards Policy and Strategy Committee on 10 January 2005 BSI 2007ISBN 978 0 580 59161 7Amendments issued since publicationAmd. No. Date Comments17212 31 July 2007 See national forewordB/546, Flexible sheets for water and water vapour control.A list of organizations represented on this committe

4、e can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.National forewordThis British Stan

5、dard is the UK implementation of EN 13969:2004, incorporating amendment A1:2006.The start and finish of text introduced or altered by amendment is indicated in the text by tags !“. Tags indicating changes to CEN text carry the number of the CEN amendment. For example, text altered by CEN amendment A

6、1 is indicated by !“.The UK participation in its preparation was entrusted to Technical Committee EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 13969December 2004ICS 01.040.91; 91.100.50English versionFlexible sheets for waterproofing - Bitumen damp proof sheetsincluding bitumen basement tanking

7、 sheets - Definitions andcharacteristicsFeuilles souples dtanchit - Feuilles bitumineusesempchant les remontes dhumidit du sol - Dfinitions etcaractristiquesAbdichtungsbahnen - Bitumenbahn-Feuchtigheitssprerren -Definitionen und EigenschaftenThis European Standard was approved by CEN on 20 October 2

8、004.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on

9、 application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat h

10、as the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slov

11、akia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2004 CEN All rights of exploitation in any form and by any means reservedworldwide for

12、 CEN national Members.Ref. No. EN 13969:2004: E+ A1November 2006EN 13969:2004 (E) 2 Contents page Foreword3 1 Scope 4 2 Normative references 4 3 Terms and definitions .5 4 Types of product6 5 Product characteristics.6 5.1 General6 5.2 Visible defects6 5.3 Dimensions and tolerances 7 5.4 Thickness an

13、d mass per unit area.7 5.5 Water tightness7 5.6 Resistance to impact.7 5.7 Durability 7 5.7.1 Against artificial ageing/degradation.7 5.7.2 Against chemicals .7 5.8 Flexibility at low temperatures (pliability) .7 5.9 Resistance to tearing (nail shank) .8 5.10 Joint strength.8 5.11 Water vapour trans

14、mission properties8 5.12 Resistance to static loading .8 5.13 Tensile properties8 5.14 Reaction to fire.8 5.15 Dangerous substances .8 6 Evaluation of conformity.9 6.1 General9 6.2 Type testing9 6.2.1 General9 6.2.2 Sampling.9 6.3 Factory production control (FPC) 9 6.3.1 General9 6.3.2 Frequency of

15、testing .9 7 Product data sheet and designation11 8 Marking, labelling and packaging 11 Annex A (informative) Information about chemical resistance .12 Annex B (informative) Example of product data sheet.14 General information14 Annex ZA (informative) Clauses of this European Standard addressing ess

16、ential requirements or other provisions of EU Directives .16 ZA.1 Scope and relevant characteristics .16 ZA.2 Procedures for attestation of conformity17 ZA.2.1 Systems of attestation of conformity 17 ZA.2.2 EC Certificate and declaration of conformity .20 ZA.3 CE marking and labelling21 Bibliography

17、 23 EN 13969:2004 (E) 3 Foreword This document (EN 13969:2004) has been prepared by Technical Committee CEN/TC 254 “Flexible sheets for waterproofing”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identi

18、cal text or by endorsement, at the latest by June 2005, and conflicting national standards shall be withdrawn at the latest by September 2006. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requi

19、rements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: A

20、ustria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Foreword to amendment A1This

21、document (EN 13969:2004/A1:2006) has been prepared by Technical Committee CEN/TC 254 “Flexible sheets for waterproofing”, the secretariat of which is held by BSI. This Amendment to the European Standard EN 13969:2004 shall be given the status of a national standard, either by publication of an ident

22、ical text or by endorsement, at the latest by May 2007, and conflicting national standards shall be withdrawn at the latest by May 2007. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: A

23、ustria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 13969:2004 (E) 4

24、1 Scope This document specifies definitions and characteristics of flexible reinforced bitumen sheets for which the intended use is as damp proofing for buildings, including basement tanking. It specifies the requirements and test methods and provides for the evaluation of conformity of the products

25、 with the requirements of this standard. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendm

26、ents) applies. EN 1109, Flexible sheets for waterproofing Bitumen sheets for roof waterproofing Determination of flexibility at low temperature EN 1296, Flexible sheets for waterproofing Bitumen, plastic and rubber sheets for roofing Method of artificial ageing by long term exposure to elevated temp

27、erature EN 1847, Flexible sheets for waterproofing Bitumen, plastic and rubber sheets for roof waterproofing Methods of exposure to liquid chemicals, including water EN 1848-1, Flexible sheets for waterproofing Determination of length, width and straightness Part 1: Bitumen sheets for roof waterproo

28、fing EN 1849-1, Flexible sheets for waterproofing Determination of thickness and mass per unit area Part 1: Bitumen sheets for roof waterproofing EN 1850-1, Flexible sheets for waterproofing Determination of visible defects Part 1: Bitumen sheets for roof waterproofing EN 1928:2000, Flexible sheets

29、for waterproofing Bitumen, plastic and rubber sheets for roof waterproofing Determination of watertightness EN 1931, Flexible sheets for waterproofing Bitumen, plastic and rubber sheets for roof waterproofing Determination of water vapour transmission properties EN 12310-1, Flexible sheets for water

30、proofing Part 1: Bitumen sheets for waterproofing Determination of resistance to tearing (nail shank) EN 12311-1, Flexible sheets for waterproofing Part 1: Bitumen sheets for roof waterproofing Determination of tensile properties EN 12316-1, Flexible sheets for waterproofing Part 1: Bitumen sheets f

31、or roof waterproofing Determination of peel resistance of joints EN 12317-1, Flexible sheets for waterproofing Part 1: Bitumen sheets for roof waterproofing - Determination of shear resistance of joints EN 12691, Flexible sheets for waterproofing Bitumen, plastic and rubber sheets for roof waterproo

32、fing Determination of resistance to impact EN 12730:2001, Flexible sheets for waterproofing Bitumen, plastic and rubber sheets for roof waterproofing Determination of resistance to static loading EN 13969:2004 (E) 5 EN 13416, Flexible sheets for waterproofing Bitumen, plastic and rubber sheets for r

33、oof waterproofing Rules for sampling EN 13501-1:2002, Fire classification of construction products and building elements Part 1: Classification using test data from reaction to fire tests EN ISO 9001, Quality management systems Requirements (ISO 9001:2000) EN ISO 11925-2, Reaction to fire tests Igni

34、tability of building products subjected to direct impingement of flame Part 2: Single-flame source test (ISO 11925-2:2002) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 13416 and the following apply. 3.1 sheet for damp proofing factory made flexible

35、 sheet made of bitumen material or composites used on or under floors or ground slabs or in walls to prevent liquid water not under hydrostatic pressure passing from the ground into the internal environment 3.2 tanking sheet factory made flexible sheet made of bitumen material or composites used in

36、wall construction, or on or under floors or ground slabs to prevent liquid water under hydrostatic pressure passing from the ground into the internal environment or from one section of the structure to another 3.3 carrier material incorporated into or onto the factory-made waterproofing sheet to ens

37、ure its stability and/or mechanical resistance 3.4 backing material incorporated onto the factory-made sheet without a permanent mechanical function 3.5 surfacing material applied to the surfaces of waterproofing sheets, either as a permanent protection against weathering on the upper surface or as

38、an anti-sticking substance on one or both surfaces of the waterproofing sheets 3.6 manufacturers limiting value MLV value stated by the manufacturer to be met during testing. The manufacturers limiting value can be a minimum or a maximum value according to statements made under product characteristi

39、cs of this document 3.7 manufacturers declared value MDV value declared by the manufacturer accompanied by a declared tolerance 3.8 oxidized bitumen straight run petroleum bitumen or a fluxed bitumen which has been hardened and rendered less temperature susceptible by blowing with air at high temper

40、ature with or without the use of a catalyst EN 13969:2004 (E) 6 3.9 elastomeric bitumen petroleum bitumen and/or oxidized bitumen modified by the addition of thermo-plastic rubbers 3.10 plastomeric bitumen petroleum bitumen and/or oxidized bitumen modified by the addition of polyolefin or polyolefin

41、 copolymer compound 3.11 reinforced bitumen sheet factory made flexible of bitumen with internal or external incorporation of one or more carriers, supplied in roll form ready to use 3.12 sampling procedure used to select or constitute a sample 3.13 sample sheet from which a test piece is taken 3.14

42、 test piece part of the sample from which test specimens are taken 3.15 test specimen piece of precise dimensions taken from the test piece 4 Types of product The types of damp proof sheets covered by this document are designated as follows: Type A: Bitumen damp proof sheet; Type T: Bitumen tanking

43、sheet. 5 Product characteristics 5.1 General 5.1.1 Where a tolerance is limited by this document it does not have to be declared by the manufacturer. 5.1.2 When tested for purposes other than initial type testing or factory production control, the tests to determine product characteristics indicated

44、 in this document shall be started within 1 month of delivery from the manufacturer. 5.2 Visible defects The product shall be free of visible defects as determined in accordance with EN 1850-1. EN 13969:2004 (E) 7 5.3 Dimensions and tolerances The length, width and straightness shall be determined i

45、n accordance with EN 1848-1. The length and width shall be greater than or equal to the manufacturers limiting value (MLV). The maximum deviation from straightness shall not exceed 20 mm per 10 m length, or in proportion for other lengths (e.g. 10 mm per 5 m length). 5.4 Thickness and mass per unit

46、area The thickness and mass per unit area shall be determined in accordance with EN 1849-1. If a product is specified by mass per unit area no single measurement shall lie outside the tolerance declared by the manufacturers declared value. If a product is specified by thickness, no single measuremen

47、t value shall lie outside the tolerance declared by the manufacturers declared value. 5.5 Water tightness Watertightness shall be determined by Method A or B of EN 1928:2000 using a pressure of 2 kPa for Type A bitumen damp proof sheets and a pressure of 60 kPa for Type T bitumen tanking sheets and

48、shall give a pass result. 5.6 Resistance to impact 5.7 Durability 5.7.1 Against artificial ageing/degradation In order to verify the artificial ageing behaviour of the product, watertightness shall be determined after exposure in accordance with EN 1296 for a period of 12 weeks. The watertightness s

49、hall be determined in accordance with EN 1928:2000 Method A or B. Type A bitumen damp proof sheets shall be tested at a pressure of 2 kPa and Type T bitumen tanking sheets at a pressure of 60 kPa and shall give a pass result. 5.7.2 Against chemicals Information about the chemical resistance of bitumen is given in Annex B. Where the product is likely to come into contact with a “not stable in all cases“ substance the resistance shall be evaluated according to