BS EN 12130-1998 Feather and down - Test methods - Determination of the filling power (massic volume)《羽毛和羽绒 试验方法 填充能力测定(整体体积)》.pdf

《BS EN 12130-1998 Feather and down - Test methods - Determination of the filling power (massic volume)《羽毛和羽绒 试验方法 填充能力测定(整体体积)》.pdf》由会员分享，可在线阅读，更多相关《BS EN 12130-1998 Feather and down - Test methods - Determination of the filling power (massic volume)《羽毛和羽绒 试验方法 填充能力测定(整体体积)》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 12130:1998 Incorpor

2、ating Corrigendum No. 1 The European Standard EN 12130:1998 has the status of a British Standard ICS 59.040 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Feather and down Test methods Determination of the filling power (massic volume)This British Standard, having been prepar

3、ed under the direction of the Sector Board for Materials and Chemicals, was published under the authority of the Standards Board and comes into effect on 15 November 1998 BSI 04-1999 ISBN 0 580 29880 9 BS EN 12130:1998 Issue 2, April 1999 Amendments issued since publication Amd. No. Date Text affect

4、ed 10425 Corrigendum April 1999 Supersession details added to National foreword National foreword This British Standard is the English language version of EN 12130:1998. It supersedes BS 5334:1976, which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee TCI/6

5、7, Household textiles, which has the responsibility to: aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and pr

6、omulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the

7、 section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct applica

8、tion. Compliance with a British Standard does not of itself confer immunity from legal obligations.Issue 1, April 1999 BS EN 12130:1998 BSI 04-1999 a Summary of pages The following table identifies the current issue of each page. Issue 1 indicates that a page has been introduced for the first time b

9、y amendment. Subsequent issue numbers indicate an updated page. Vertical sidelining on replacement pages indicates the most recent changes (amendment, addition, deletion). Page Issue Page Issue Front cover Inside front cover a b 2 2 1 blank EN title page EN foreword 3t o7 Back cover original origina

10、l original originalb blankCEN European Committee for Standardization Comite Europe en de Normalisation Europa isches Komitee fu r Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1998 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN nateional mem

11、bers. Ref. No. 12130:1998 E EUROPEAN STANDARD EN 12130 NORME EUROPE ENNE EUROPA ISCHE NORM April 1998 ICS 59.040 Descriptors: stuffings, feathers, tests, determination, density (mass/volume), testing conditions English version Feather and down Test methods Determination of the filling power (massic

12、volume) Plumes et duvets Me thodes dessais De termination du pouvoir gonflant (volume massique) Federn und Daunen Pru fverfahren Bestimmung der Fu llkraft (Fu llvolumen) This European Standard was approved by CEN on 23 March 1998. CEN members are bound to comply with the CEN/CENELEC Internal Regulat

13、ions which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This Euro

14、pean Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the nati

15、onal standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.Page 2 EN 12130:1998 BSI 1998 Foreword This European Standard has been prepared by T

16、echnical Committee CEN/TC 222, Feather and down as filling material for any article, as well as finished articles filled with feather and down, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text

17、 or by endorsement, at the latest by October 1998, and conflicting national standards shall be withdrawn at the latest by October 1998. Annex A is informative. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement th

18、is European standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.Page 3 EN 12130:1998 BSI 1998 1 Scope This European Standard specifies the procedur

19、e for determining the filling power (massic volume). This method is applicable to finished down and/or feather, fit for or constituting filled manufactured articles (e.g. anoraks, quilts, etc.) 2 Normative references This European Standard incorporates by dated or undated reference, provisions from

20、other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or

21、 revision. For undated references the latest edition of the publication referred to applies. prEN 1883, Feather and down Sampling in view of tests. EN 20139, Textiles Standard atmospheres for conditioning and testing (ISO 139:1973). EN 20187, Paper, board and pulps Standard atmosphere for conditioni

22、ng and testing and procedure for monitoring the atmosphere and conditioning of samples (ISO 187:1990). 3 Definitions For the purposes of this standard the following definitions apply. 3.1 filling power (fp) height of the volume occupied by filling material subjected to a specific pressure, expressed

23、 in millimetres NOTE The volume comprises internal pores of elements and pore spaces between elements. 3.2 massic volume volume occupied by a given mass of filling material, when subjected to a specific pressure; it is expressed in cubic centimetres per gram 4 Principle A test specimen, suitably pre

24、pared, having a specified mass is placed in a cylinder and the material is aerated by blowing for a set period. Pressure by way of a platen is then applied to the filling material at a constant speed and after a stipulated time the level of the platen is noted. The massic volume is calculated with r

25、egard to the height and the known diameter of the graduated cylinder. 5 Apparatus It is allowed to use any kind of apparatus on condition that it gives the same results, within experimental error, like the one described below. These alternative apparatus should be of such design to give satisfactory

26、 performance, particularly for a good air blowing of the test specimen. 5.1 Tester (see Figure 1) which consists of: 5.1.1 Cylinder, with flat bottom standing on a base capable of being levelled by adjustable legs, with internal diameter of (289 1) mm and (500 5) mm high. The cylinder shall be made

27、from smooth, antistatic and transparent material (e.g. acrylic). 5.1.2 Plunger and measuring rod, of mass giving a pressure of (14,8 0,2) Pa. The plunger, suspended by measuring rod, with diameter (282 3) mm shall have its underside flat and smooth and made of a rigid material, so that it does not b

28、ecome deformed in use. The measuring rod, marked in millimetres, shall be at zero when the plunger is resting on the bottom of the cylinder. Instead of the measuring rod, it is possible to use any kind of device on condition that the pressure exerted on the material is of (14,8 0,2) Pa. NOTE A vacuu

29、m cleaner can be used as a suitable blower. 5.1.3 Cover, mounted in a frame which fits over the cylinder, consists of a wire screen of nominal aperture size 180 mm and a wire diameter 125 mm (see ISO 3310-1). In the centre of the cover is inserted a blow nozzle (5.1.4). 5.1.4 Blow nozzle, (see Figur

30、e 2) equipped with an adjustable valve in order to regulate the amount of the air injected. 5.1.5 Device regulating the descent of the plunger and measuring rod at (520 20) mm/min. 5.2 Blower, with a suitable tube connected to its exhaust vent and capable of guaranteeing an air flow, measured at a d

31、istance of 400 mm from the inlet nozzle, of (310 50) l/min. 5.3 Stop watch 5.4 Balance, sensitive to 0,05 g 5.5 Sample preparation box of wire net, having dimensions which will contain a sample up to at least 50 g with the height of material less than 150 mm.Page 4 EN 12130:1998 BSI 1998 6 Preparati

32、on and conditioning of sample and equipment 6.1 A mass of at least 50 g is obtained from the material to be tested, in accordance with the procedure described in prEN 1883. The sample is placed in an adequate container (substituting for the cylinder in 5.1.1) and the cover is applied. With the valve

33、 aperture set for maximum air flow, air is blown into the container for (60 5) s. 6.2 The sample is then removed from the container and conditioned in the atmosphere as defined in EN 20139, and controlling the relative humidity in accordance with EN 20187 by storing it loose to a maximum height of 1

34、50 mm in sample preparation box (5.5) for at least 48 h. 6.3 It is necessary to wash the cylinder after 30 measurements (15 test specimens) with warm water prepared with anionic-active detergent (concentration: 0,4 ml/l) followed by two rinses with cold distilled water. To ensure reliability of the

35、procedure, and if doubtful of the influence of static electricity on the result, proceed as follows. Record the height of the plunger at the end of the first test and leave the plunger in place for at least 2 h. Measure again the height of the plunger. If the new measurement differs from the first b

36、y more than 2 cm, repeat the procedure starting at 6.2. 7 Procedure 7.1 Conditioning is carried out according to EN 20139 and the temperature and relative humidity are measured according to EN 20187. 7.2 Ensure that the cylinder is vertical by adjusting the legs and that the measuring rod is at zero

37、 when the plunger is standing on the bottom of the cylinder. 7.3 Weigh out (20,0 0,1) g of two test specimens each extracted from the sample (6.1) and place the first test specimen in the cylinder and apply the cover. 7.4 The test specimen is loosened by blowing for (60 5) s. It is essential that bl

38、owing is halted immediately. 7.5 Insert the plunger and measuring rod into the top of cylinder and lower mechanically or manually towards the test specimen at a constant speed of (520 20) mm/min until the plunger is standing horizontally or almost horizontally on the test specimen. If not, repeat th

39、e blowing on the same test specimen. 7.6 Read from on the measuring rod the height of the material after a period of (60 2) s. As far as possible, position the plunger in the centre of the cylinder for the whole test. 7.7 Repeat steps 7.4, 7.5 and 7.6 using the same test specimen which is loosened b

40、y blowing for (7 3) s, as described above prior to each reading. Note the average of the values, in millimetres. 7.8 Repeat steps 7.3 to 7.7 for the duplicate test specimen. 8 Calculation and expression of results 8.1 Filling power: Recorded in millimetres. Calculate the mean of the results obtained

41、 on the two test specimens and report them with the symbol, fp. 8.2 Massic volume 8.2.1 From the mean results of fp obtained for each test specimen, calculate the massic volume (V) in cubic centimetres per gram with the approximation to the first decimal with the formula: V= H3a m31000 where: H is t

42、he mean height of two determinations (7.7), obtained on one test specimen, expressed in millimetres; a is the test surface area of the cylinder expressed in square millimetres; m is the mass of the test specimen, in grams. 8.2.2 Calculate the average of the bulk density obtained for the two test spe

43、cimens. 9 Precision of the method Based on data from one interlaboratory test carried out by eleven laboratories on five different samples and two determinations for sample, and from another interlaboratory test carried out by ten laboratories on nine samples and two determinations for a sample, the

44、 following precision data were found for the filling power: Repeatability: The 95 % probability of the repeatability limit (r) for the difference between two test results within a single laboratory was about 3 mm for different filling samples. Reproducibility: The 95 % probability of the reproducibi

45、lity limit (R) for the difference between two test results from different laboratories was about 15 mm for different filling samples. 10 Test report The test report shall include at least the following information: the reference to this standard; the description of the test material; the mass of the

46、 test specimen in grams; the filling power in millimetres; the massic volume, in cubic centimetres per grams, if required; any deviation from the standard procedure and any other circumstances that may have affected the result.Page 5 EN 12130:1998 BSI 1998 Dimensions in millimetres Figure 1 Filling

47、power testerPage 6 EN 12130:1998 BSI 1998 Dimensions in millimetres All holes evenly distributed around one nozzle Figure 2 Blow nozzlePage 7 EN 12130:1998 BSI 1998 Annex A (informative) Bibliography ISO 3310-1, Test sieves Technical requirements and testing Part 1: Test sieves of metal wire cloth.B

48、SI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI Br

49、itish Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be g