BS EN 10217-2-2002 Welded steel tubes for pressure purposes - Technical delivery conditions - Electric welded non-alloy and alloy steel tubes with specified elevated temperature pr.pdf

《BS EN 10217-2-2002 Welded steel tubes for pressure purposes - Technical delivery conditions - Electric welded non-alloy and alloy steel tubes with specified elevated temperature pr.pdf》由会员分享，可在线阅读，更多相关《BS EN 10217-2-2002 Welded steel tubes for pressure purposes - Technical delivery conditions - Electric welded non-alloy and alloy steel tubes with specified elevated temperature pr.pdf（30页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 10217-2:2002Incorporating Amendment No. 1Welded steel tubes for pressure purposes Technical delivery conditions Part 2: Electric welded non-alloy and alloy steel tubes with specified elevated temperature propertiesThe European Standard EN 10217-2:2002, with the incorporation of

2、 amendment A1:2005, has the status of a British StandardICS 23.040.10; 77.140.75 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58Licensed Copy: Wang

3、 Bin, na, Fri May 12 04:05:59 BST 2006, Uncontrolled Copy, (c) BSIBS EN 10217-2:2002This British Standard was published under the authority of the Standards Policy and Strategy Committee on 26 June 2002 BSI 14 February 2006ISBN 0 580 39842 0National forewordThis British Standard is the official Engl

4、ish language version of EN 10217-2:2002, including Amendment No. 1. Together with BS EN 10216-2:2002 it supersedes BS 3059-2:1990, BS 3602-1:1987, BS 3604-1:1990 and BS 3606:1992 which are withdrawn.The start and finish of text introduced or altered by amendment is indicated in the text by tags !“.

5、Tags indicating changes to CEN text carry the number of the amendment. For example, text altered by CEN amendment A11 is indicated by AB.The UK participation in its preparation was entrusted by Technical Committee ISE/73, Steels for pressure purposes, to Subcommittee ISE/73/1, Steel tubes for pressu

6、re purposes, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary.Cross-referencesThe British Standards which implement international or European publications referred to in this document may be found in the BSI Catalog

7、ue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correc

8、t application.Compliance with a British Standard does not of itself confer immunity from legal obligations.Summary of pages aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep UK inte

9、rests informed; monitor related international and European developments and promulgate them in the UK.This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 27 and a back cover.The BSI copyright notice displayed in this document indicates when the document was la

10、st issued.Amendments issued since publicationAmd. No. Date Comments15472 Amendment No. 114 February 2006 See national forewordLicensed Copy: Wang Bin, na, Fri May 12 04:05:59 BST 2006, Uncontrolled Copy, (c) BSIEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORMEN 10217-2May 2002ICS 23.040.10; 77.140.

11、75English versionWelded steel tubes for pressure purposes - Technical delivery conditions - Part 2: Electric welded non-alloy and alloy steel tubes with specified elevated temperature propertiesTubes souds en acier pour service sous pression -Conditions techniques de livraison - Partie 2: Tubes soud

12、s lectriquement en acier non alli et alli avec caractristiques spcifies temprature leveGeschweite Stahlrohre fr Druckbeanspruchungen -Technische Lieferbedingungen - Teil 2: Elektrisch geschweite Rohre aus unlegierten und legierten Sthlen mit festgelegten Eigenschaften bei erhhten TemperaturenThis Eu

13、ropean Standard was approved by CEN on 25 April 2002; amendment A1 was approved by CEN on 9 December 2004.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteratio

14、n. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translation u

15、nder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions.EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels

16、2002 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members.+A1January 2005(inclut lamendement A1:2005) (enthlt nderung A1:2005)CEN members are the national standards bodies of Austria, Belgium, Cyrprus, Czech Republic, Denmark, Estonia, Finland, Fran

17、ce, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Ref. No. EN 10217-2:2002 + A1:2005 E(incudes amendment A1:2005)Licensed Copy: Wang Bin, na, Fri May 1

18、2 04:05:59 BST 2006, Uncontrolled Copy, (c) BSI2Contents1 SCOPE 42 NORMATIVE REFERENCES . 43 TERMS AND DEFINITIONS . 54 SYMBOLS. 55 CLASSIFICATION AND DESIGNATION . 55.1 Classification . 55.2 Designation 66 Information to be supplied by the purchaser . 66.1 Mandatory information 66.2 Options . 67 Ma

19、nufacturing process. 77.1 Steelmaking process. 77.2 Deoxidation process . 77.3 Tube manufacture and delivery conditions 78 requirements 88.1 General . 88.2 Chemical composition 88.3 Mechanical properties. 98.4 Appearance and internal soundness 128.5 Straightness. 138.6 Preparation of ends. 138.7 Dim

20、ensions, masses and tolerances 139 Inspection. 179.1 Types of inspection. 179.2 Inspection documents 179.2.1 Types of inspection documents. 1710 SAMPLING 1910.1 Frequency of tests. 1910.2 Preparation of samples and test pieces 1911 Test methods . 2011.1 Chemical analysis . 2011.2 Tensile test on bas

21、e material . 2111.3 Transverse tensile test on the weld. 2111.4 Flattening test 2111.5 Ring tensile test. 2111.6 Drift expanding test. 2211.7 Ring expanding test 2211.8 Impact test 2211.9 Leak tightness test 2311.10 Dimensional inspection 2311.11 Visual examination 2411.12 Non-Destructive Testing. 2

22、411.13 Material identification 2411.14 Retests, sorting and reprocessing 2412 MARKING 2412.1 Marking to be applied 2412.2 Additional marking 2513 PROTECTION. 25Annex ZA (informative) Relationship between this European Standard and the EssentialRequirements of 97/23/EC 26Bibliography 27Foreword 39.2.

23、2 Content of inspection documents 18EN 10217-2:2002 (E)Licensed Copy: Wang Bin, na, Fri May 12 04:05:59 BST 2006, Uncontrolled Copy, (c) BSIEN 10217-2:2002 (E)3ForewordThis document (EN 10217-2:2002) has been prepared by Technical Committee ECISS/TC 29, “Steel tubes andfittings for steel tubes“, the

24、 secretariat of which is held by UNI.This European Standard shall be given the status of a national standard, either by publication of an identical textor by endorsement, at the latest by November 2002, and conflicting national standards shall be withdrawn at thelatest by November 2002.This document

25、 has been prepared under a mandate given to CEN by the European Commission and theEuropean Free Trade Association, and supports essential requirements of EU Directive(s).For relationship with EU Directive(s), see informative annex ZA, which is an integral part of this document.Other parts of EN 1021

26、7 are:Part 1: Non-alloy steel tubes with specified room temperature propertiesPart 3: Alloy fine grain steel tubes.Part 4: Electric welded non-alloy steel tubes with specified low temperature propertiesPart 5: Submerged arc welded non-alloy and alloy steel tubes with specified elevated temperaturepr

27、operties.Part 6: Submerged arc welded non-alloy steel tubes with specified low temperature properties.Part 7: Stainless steel tubes.Another European Standard series covering tubes for pressure purposes is:EN 10216: Seamless steel tubes for pressure purposes.According to the CEN/CENELEC Internal Regu

28、lations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain,Sweden, Switzerland and

29、the United Kingdom.Foreword to amendment 1 This document (EN 10217-2:2002/A1:2005) has been prepared by Technical Committee ECISS/TC 29 “Steel tubes and fittings for steel tubes”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either

30、 by publication of an identical text or by endorsement, at the latest by July 2005, and conflicting national standards shall be withdrawn at the latest by July 2005. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and s

31、upports essential requirements of EU Directive 97/23/EC. For relationship with EU Directive 97/23/EC, see informative Annex ZA, which is an integral part of this document. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to

32、implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kin

33、gdom. Licensed Copy: Wang Bin, na, Fri May 12 04:05:59 BST 2006, Uncontrolled Copy, (c) BSIEN 10217-2:2002 (E)41 SCOPEThis Part of EN 10217 specifies the technical delivery conditions in two test categories of electric welded tubes ofcircular cross section, with specified elevated temperature proper

34、ties, made of non-alloy and alloy steel.2 NORMATIVE REFERENCESThis European Standard incorporates by date or undated reference, provisions from other publications. Thesenormative references are cited at the appropriate places in the text and the publications are listed hereafter. Fordate references,

35、 subsequent amendments to or revisions of, any of these publications apply to this EuropeanStandard only when incorporated in it by amendment or revision. For undated references the latest edition of thepublication referred to applies (including amendments).The requirements of this European Standard

36、 rule when they differ from those in the standards and documentsreferred to below:EN 10002-1, Metallic materials - Tensile testing - Part 1 : Method of test (at ambient temperature.EN 10002-5, Metallic materials - Tensile testing - Part 5 : Method of testing at elevated temperatureEN 10020, Definiti

37、ons and classification of grades of steelEN 10021, General technical delivery requirements for steel and iron productsEN 10027-1, Designation systems for steels - Part 1 : Steel names, principle symbols.EN 10027-2, Designation systems for steels Part 2 : Numerical systems.EN 10045-1, Metallic materi

38、als - Charpy impact test - Part 1 : Test methodEN 10052, Vocabulary of heat treatment terms for ferrous productsEN 10204, Metallic products - Types of inspection documentsENV 10220, Seamless and welded steel tubes - Dimensions and masses per unit lengthEN 10233, Metallic materials - Tubes - Flatteni

39、ng testEN 10234, Metallic materials - Tubes - Drift expanding testEN 10236, Metallic materials - Tubes - Ring expanding testEN 10237, Metallic materials - Tubes - Ring tensile testEN 10246-1, Non-Destructive Testing of steel tubes Part 1 : Automatic electromagnetic testing of seamless andwelded (exc

40、ept submerged arc welded) ferromagnetic steel tubes for verification of hydraulic leak-tightnessEN 10246-3,Non-Destructive Testing of steel tubes - Part 3 :Automatic eddy current testing of seamless andwelded (except submerged arc-welded) steel tubes for the detection of imperfectionsEN 10246-5,Non-

41、Destructive Testing of steel tubes Part 5: Automatic full peripheral magnetic transducer/fluxleakage testing of seamless and welded (except submerged arc-welded) ferromagnetic steel tubes for thedetection of longitudinal imperfectionsEN 10246-6, Non-Destructive Testing of steel tubes - Part 6 : Auto

42、matic full peripheral ultrasonic testing ofseamless steel tubes for the detection of transverse imperfectionsEN 10246-7, Non-Destructive Testing of steel tubes - Part 7 : Automatic full peripheral ultrasonic testing ofseamless and welded (except submerged arc welded) steel tubes for the detection of

43、 longitudinal imperfectionsLicensed Copy: Wang Bin, na, Fri May 12 04:05:59 BST 2006, Uncontrolled Copy, (c) BSIEN 10217-2:2002 (E)5EN 10246-8, Non-Destructive Testing of steel tubes Part 8: Automatic ultrasonic testing of the weld seam ofelectric welded tubes for the detection of longitudinal imper

44、fectionsEN 10246-14, Non-Destructive Testing of steel tubes - Part 7 : Automatic ultrasonic testing of seamless andwelded (except submerged arc welded) steel tubes for the detection of laminar imperfectionsEN 10256,Non-Destructive Testing of steel tubes - Qualification and competence of level 1 and

45、level 2 NDTpersonnelEN ISO 377,Steel and steel products - Location and preparation of samples and test pieces for mechanicaltesting (ISO 377:1997)EN ISO 2566-1, Steel - Conversion of elongation values Part 1: Carbon and low-alloy steels (ISO 2566-1:1984)prEN 102661),Steel tubes, fittings and structu

46、ral hollow sections - Symbols and definition of terms for use inproduct standardsprEN 10168 1), Iron and steel products - Inspection documents - List of information and descriptionISO 14284, Steel and iron - Sampling and preparation of samples for the determination of chemical compositionCR 10260, D

47、esignation systems for steel - Additional symbolsCR 10261, ECISS Information Circular IC 11 - Iron and steel - Review of available methods of chemical analysis.3 TERMS AND DEFINITIONSFor the purposes of this Part of EN 10217 the terms and definitions, given in EN 10020, EN 10021, EN 10052,prEN 10266

48、 and the following apply:3.1test categoryclassification that indicates the extent and level of inspection and testing.3.2employerorganisation for which a person works on a regular basis.NOTE The employer may be either the tube manufacturer or supplier or a third party organisation providing Non-Dest

49、ructive Testing (NDT) services.4 SYMBOLSFor the purposes of this part of EN 10217, the symbols given in prEN 10266 and the following apply:C1, C2 category conformity indicators (see clauses 7.3.1 and 7.3.3.)TC test category.1) In preparation; until this document is published as a European standard, a corresponding national standardshould be agreed at the time of enquiry and order.Licensed Copy: Wang Bin, na, Fri May 12 04:05:59 BST 2006, Uncontrolled Copy, (c) BSIEN 10217-2:2002 (E)65 CLASSIFICATION AND DESIGNATION5.1 ClassificationIn accorda