BS EN 3307-1997 Screws pan head offset cruciform recess threaded to head in titanium alloy anodized MoS2 lubricated - Classification 1100 MPa (at ambient temperature) 315 C《二硫化钼润滑的.pdf

《BS EN 3307-1997 Screws pan head offset cruciform recess threaded to head in titanium alloy anodized MoS2 lubricated - Classification 1100 MPa (at ambient temperature) 315 C《二硫化钼润滑的.pdf》由会员分享，可在线阅读，更多相关《BS EN 3307-1997 Screws pan head offset cruciform recess threaded to head in titanium alloy anodized MoS2 lubricated - Classification 1100 MPa (at ambient temperature) 315 C《二硫化钼润滑的.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD AEROSPACE SERIES BS EN 3307:1997 Screws, pan head, offset cruciform recess, threaded to head, in titanium alloy, anodized, MoS 2lubricated Classification: 1100MPa (at ambient temperature)/315 C The European Standard EN 3307:1996 has the status of a British Standard ICS 49.030.20BSEN

2、3307:1997 This British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authorityof the Standards Board and comes into effect on 15 February 1997 BSI 12-1998 The following BSI references relate to the work on this standard: Committee referen

3、ce ACE/12 Draft for comment 92/74427 DC ISBN 0 580 27036 X Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee ACE/12, Aerospace fasteners and fastening systems, upon which the following bodies were represented: Association o

4、f Electronics, Telecommunications, and Business Equipment Industries British Industrial Fasteners Federation Ministry of Defence Society of British Aerospace Companies Ltd. Amendments issued since publication Amd. No. Date CommentsBSEN3307:1997 BSI 12-1998 i Contents Page Committees responsible Insi

5、de front cover National foreword ii Foreword 2 1 Scope 3 2 Normative references 3 3 Required characteristics 3 4 Designation 6 5 Marking 6 6 Technical specification 6 Figure 1 4 Table 1 5 Table 2 6 Table 3 6 List of references Inside back coverBSEN3307:1997 ii BSI 12-1998 National foreword This Brit

6、ish Standard has been prepared by Technical Committee ACE/12 and is the English language version of EN 3307:1996 Aerospace series Screws, pan head, offset cruciform recess, threaded to head, in titanium alloy, anodized, MoS 2lubricated Classification: 1100MPa (at ambient temperature)/315 C, publishe

7、d by the European Committee for Standardization (CEN). EN 3307:1996 was produced as a result of international discussions in which the United Kingdom took an active part. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are respons

8、ible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-references Publication referred to Corresponding British Standard EN 2000:1991 BS EN 2000:1992 Quality assurance EN aerospace products Approval of the quality syste

9、m of manufacturers EN 2424:1995 BS EN 2424:1995 Marking of aerospace products ISO 3353:1992 BS 2A 231:1993 Rolled threads for bolts. Lead and runout requirements ISO 5855-2:1988 BS 6293 Aerospace. MJ threads Part 2:1994 Limit dimensions for bolts and nuts ISO 7913:1994 BS 2A 296:1995 Bolts and screw

10、s, metric Tolerances of form and position ISO 7994:1985 BS A 297:1987 Specification for internal drive, offset cruciform recess (Torq-Set ) for rotary fastening devices. Metric series Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theEN title page, pag

11、es 2 to 6, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on theinside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 3307 September 1996 ICS 49.040.2

12、0 Descriptors: Aircraft industry, screw, cheese head screw, cross recessed screw, titanium alloy, specification, dimension, dimensional tolerance, surface treatment, designation, marking English version Aerospace series Screws, pan head, offset cruciformrecess, threaded to head, in titanium alloy,an

13、odized, MoS 2lubricated Classification: 1100MPa (at ambient temperature)/315 C Srie arospatiale Vis tte cylindrique, empreinte cruciforme dporte, filetes jusqu proximit de la tte, en alliage de titane, anodises, lubrifies MoS 2 Classification: 1100MPa ( temprature ambiante) /315 C Luft-und Raumfahrt

14、 Flachkopfschrauben mit Flgelkreuzschlitz, Gewinde annhernd bis Kopf, aus Titanlegierung, anodisiert, MoS 2 geschmiert Klasse: 1100MPa (beiRaumtemperatur) /315 C This European Standard was approved by CEN on 1996-06-29. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which

15、stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. The European Standar

16、ds exist in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standar

17、ds bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Centra

18、l Secretariat: rue de Stassart 36, B-1050 Brussels 1996 Copyright reserved to CEN members Ref. No. EN 3307:1996 EEN3307:1996 BSI 12-1998 2 Foreword This European Standard has been prepared by the European Association of Aerospace Manufacturers (AECMA). After inquiries and votes carried out in accord

19、ance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication o

20、f an identical text or by endorsement, at the latest by March1997, and conflicting national standards shall be withdrawn at the latest by March1997. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European

21、 Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.EN3307:1996 BSI 12-1998 3 1 Scope This standard specifies the characteristics of screws, pan head, offset cruc

22、iform recess, threaded to head, in titanium alloy, anodized, MoS 2lubricated. Classification: 1100 MPa 1) /315C 2) 2 Normative references This European Standard incorporates by dated or undated reference provisions from other publications. These normative references are cited at the appropriate plac

23、es in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication refer

24、red to applies. ISO 3202, Aerospace Screws, pan head, internal offset cruciform ribbed drive, threaded to head, MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1100 MPa Dimensions. ISO 3353, Aerospace Rolled threads for bolts Lead and runout requirements. IS

25、O 5855-2, Aerospace MJ threads Part 2: Limit dimensions for bolts and nuts. ISO 7913, Aerospace Bolts and screws, metric Tolerances of form and position. ISO 7994, Aerospace Internal drive, offset cruciform recess (Torq-Set ) for rotary fastening devices Metric series. ISO 9152, Aerospace Titanium a

26、lloy bolts, strength class 1100MPa, MJ threads Procurement specification 3) . EN 2000, Aerospace series Quality assurance ENaerospace products Approval of the quality system of manufacturers. EN 2424, Aerospace series Marking of aerospace products. EN 2491, Aerospace series Molybdenum disulphide dry

27、 lubricants Coating methods 4) . TR 3775, Aerospace series Bolts and pins National materials 5) . TR 4070, Aerospace series Molybdenum disulphide dry lubricants List of commercial products 3) . 3 Required characteristics 3.1 Configuration Dimensions Masses See Figure 1 and Table 1. Dimensions and to

28、lerances are: in conformity with ISO3202, expressed in millimetres and apply after anodizing but before lubricating. 3.2 Tolerances of form and position ISO 7913 3.3 Materials TR 3775 (titanium alloy, strength class 1100MPa) 3.4 Surface treatment Lubrication: lubricant: see TR4070; application: EN 2

29、491:5m to 10 m. 1) Minimum tensile strength of the material at ambient temperature 2) Maximum temperature that the screw can withstand without continuous change in its original characteristics, after return to ambient temperature. The maximum temperature is determined by the surface treatment. 3) In

30、 preparation at the date of publication of this standard 4) Published as AECMA Standard at the date of publication of this standard 5) Published as AECMA Technical Report at the date of publication of this standardEN 3307:1996 4 BSI 12-1998 Figure 1EN 3307:1996 BSI 12-1998 5 Table 1 Diameter code Th

31、read a D 1 D 2 D 3 E L 0,3 bc R S Mass d min. nom. Tol. nom. Tol. Code nom. nom. Tol. max. min. e f 030 MJ30,5 4h6h 6 4,7 2,3 1,8 004 to 042 4 to 42 0,4 1,2 0,3 0,31 0,05 040 MJ40,7 4h6h 8 6,7 3 2,4 006 to 056 6 to 56 1,6 0,4 0,80 0,08 050 MJ50,8 4h6h 10 8,7 3,4 3 008 to 070 8 to 70 0,5 2 0,5 1,58 0

32、,14 060 MJ61 4h6h 12 10,7 4,2 3,6 010 to 084 10 to 84 0,7 2,4 0,6 2,50 0,20 070 MJ71 4h6h 14 12,7 5,2 4,2 010 to 098 10 to 98 2,8 0,7 4,59 0,31 080 MJ81 4h6h 16 14,7 6,2 0,5 4,8 010 to 112 10 to 112 3,2 0,8 5,95 0,44 100 MJ101,25 4h6h 20 18,7 7,9 6 014 to 140 14 to 140 0,8 4 1 10,58 0,59 120 MJ121,2

33、5 4h6h 24 22,7 9,8 7,2 016 to 168 16 to 168 0,9 4,8 1,2 22,54 1 a In accordance with ISO 5855-2 b Increments: 2 for L 100 4 for L 100 c If greater lengths are required, they shall be chosen using the above increments. The length code corresponds to the length L, completed by one or two zeros to the

34、left, where necessary, to obtain a three digit code. d Approximate values (kg/1000 pieces), calculated on the basis of 4,45 kg/dm 3 , given for information purposes only e Value for head and first L f Increase for each additional 2 mm of L 00,3 005 , 002 , 003 , 002 , 003 , EN3307:1996 6 BSI 12-1998

35、 4 Designation EXAMPLE: NOTEIf necessary, the code 19005 shall be placed between the description block and the identity block. Table 2 5 Marking See Table 3 and Figure 1, indented. Table 3 6 Technical specification ISO 9152, except for clauses: Approval of manufacturers: see EN 2000; Qualification o

36、f bolts: not applicable. Drive Code ISO 7994 R ISO 7994 unribbed A Diameter code EN 2424 Style 030 and 040 N 050 to 120 C + MJBSEN3307:1997 BSI 12-1998 List of references See national foreword.BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

37、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standar

38、ds. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constan

39、t aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:

40、020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Custome

41、r Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of informati

42、on on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996

43、7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in al

44、l BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means el

45、ectronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.