BS EN 1850-2-2001 Flexible sheets for waterproofing - Determination of visible defects - Plastic and rubber sheets for roof waterproofing《防水柔性板 可视缺陷的测定 屋顶防水用塑料和橡胶薄板》.pdf

《BS EN 1850-2-2001 Flexible sheets for waterproofing - Determination of visible defects - Plastic and rubber sheets for roof waterproofing《防水柔性板 可视缺陷的测定 屋顶防水用塑料和橡胶薄板》.pdf》由会员分享，可在线阅读，更多相关《BS EN 1850-2-2001 Flexible sheets for waterproofing - Determination of visible defects - Plastic and rubber sheets for roof waterproofing《防水柔性板 可视缺陷的测定 屋顶防水用塑料和橡胶薄板》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 1850-2:2001 Flexible sheets for waterproofing Determination of visible defects Part 2: Plastic and rubber sheets for roof waterproofing The European Standard EN 1850-2:2001 has the status of a British Standard ICS 83.140.10; 91.100.50 NO COPYING WITHOUT BSI PERMISSION EXCEPT A

2、S PERMITTED BY COPYRIGHT LAWBS EN 1850-2:2001 This British Standard, having been prepared under the direction of the Sector Committee for Building and Civil Engineering, was published under the authority of the Standards Committee and comes into effect on 15 July 2001 BSI 07-2001 ISBN 0 580 36352 X

3、National foreword This British Standard is the official English language version of EN 1850-2:2001. The UK participation in its preparation was entrusted by Technical Committee B/546, Flexible sheets for waterproofing, to Subcommittee B/546/2, Roof sheeting and sealing sheeting, which has the respon

4、sibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications may be found in the BSI Standards Catalogue under the section entitled “International Stand

5、ards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standa

6、rd does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments

7、and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 4, an inside back cover and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since

8、 publication Amd. No. Date CommentsEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1850-2 May 2001 ICS 91.100.50 English version Flexible sheets for waterproofing Determination of visible defects Part 2: Plastic and rubber sheets for roof waterproofing Feuilles souples dtanchit Dtermination des

9、 dfauts daspect Partie 2: Feuilles dtanchit de toiture plastiques et lastomres Abdichtungsbahnen Bestimmung sichtbarer Mngel Teil 2: Kunststoffbahnen und Elastomerbahnen fr Dachabdichtungen This European Standard was approved by CEN on 2 June 2000. CEN members are bound to comply with the CEN/CENELE

10、C Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN m

11、ember. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN member

12、s are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION

13、 EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2001 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1850-2:2001 EPage 2 EN 1850-2:2001 BSI 07-2001 Contents Page Foreword .3 Introduction3 1 Sc

14、ope .3 2 Normative references.3 3 Terms and definitions.3 4 Principle .4 5 Sampling and conditioning .4 6 Procedure.4 7 Test report4Page 3 EN 1850-2:2001 BSI 07-2001 Foreword This European Standard has been prepared by Technical Committee CEN/TC 254, Flexible sheets for waterproofing, the Secretaria

15、t of which is held by BSI. This document has to be implemented at national level, either by publication of an identical text or by endorsement, by November 2001, and conflicting national standards have to be withdrawn by July 2002. According to the CEN/CENELEC Internal Regulations, the national stan

16、dards organizations of the following countries are bound to implement this document: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Introduction This E

17、uropean Standard is intended for characterization of plastic and rubber sheets as manufactured or supplied before use. This test method relates exclusively to products or to their components where appropriate, and not to waterproofing membrane systems composed of such products and installed in the w

18、orks. This test is intended to be used in conjunction with a European Standard on definition and characteristics for plastic and rubber sheets for roof waterproofing. 1 Scope This European Standard specifies a method for the determination of the visible defects in plastic and rubber sheets for roof

19、waterproofing, which could influence the functional behaviour of these sheets. 2 Normative references This European Standard incorporates, by dated or undated references, provisions from other publications. These normative references are cited at the appropriate places in the text and the publicatio

20、ns are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references, the latest editions of the publication referred to apply (including amendme

21、nts). EN 13416 Flexible sheets for waterproofing Bitumen, plastic and rubber sheets for roof waterproofing Rules for sampling. 3 Terms and definitions For the purpose of this European Standard, the following terms and definitions apply. 3.1 blister elevation of the surface of varied contour and dime

22、nsions, with a cavity beneath it 3.2 crack fissure that penetrates the external surface of the material or its entire thickness, the rubber or plastic material being completely separated between the crack walls 3.3 hole opening through the sheet, which may allow the passage of water 3.4 scratch sing

23、le sided damage to the surface caused by external meansPage 4 EN 1850-2:2001 BSI 07-2001 3.5 indentation small hollow or depression in the surface of the sheet 3.6 void enclosed cavity of an undefined shape, containing air or some other gas NOTE The term bubble refers to a more or less spherical voi

24、d. 3.7 inclusion extraneous body enclosed within the mass. 4 Principle A part of a selected roll of plastic or rubber sheet is unrolled on a flat surface and examined for defects on both surfaces and at a cut surface. 5 Sampling and conditioning 5.1 Sampling The plastic or rubber sheet to be tested

25、shall be complete and undamaged rolls selected in accordance with EN 13416. 5.2 Conditioning of samples Generally ageing or conditioning is not required to be carried out and examination shall be made under ambient conditions. In case of dispute, the test shall be conducted at (23 2) C after conditi

26、oning for at least 20 h at (23 2) C. 6 Procedure The selected roll shall be laid on a flat surface. The first 10 m of the roll of material under examination is carefully unrolled, top surface uppermost, and examined over the whole surface with the naked eye for the presence of blisters, cracks, hole

27、s, scratches, indentations, or any other noticeable defect. The roll is then carefully turned over and examined on the underside for the same visible defects. Cut the roll near the end across the full width and examine the cut surface for the presence of voids or inclusions. 7 Test report The test r

28、eport shall contain at least the following information: a) a reference to this European Standard (EN 1850-2) and any deviation from it; b) all details necessary to identify the product tested; c) any non-standard procedures or any peculiarities encountered during testing; d) the presence of any blis

29、ters, cracks, holes, scratches or indentations; e) the presence of any inclusions or voids in the cut surface; f) the date of testing.blankBS EN 1850-2:2001 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing Briti

30、sh Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is t

31、he constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front co

32、ver. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed

33、to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless other

34、wise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products a

35、nd services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administrat

36、ion. Tel: 020 8996 7002. Fax: 020 8996 7001. Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as perm

37、itted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course

38、 of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.