BS 6161-18-1991 Methods of test for anodic oxidation coatings on aluminium and its alloys - Determination of surface abrasion resistance《铝及铝合金阳极氧化镀层试验方法 第18部分 表面耐磨性测定》.pdf
《BS 6161-18-1991 Methods of test for anodic oxidation coatings on aluminium and its alloys - Determination of surface abrasion resistance《铝及铝合金阳极氧化镀层试验方法 第18部分 表面耐磨性测定》.pdf》由会员分享,可在线阅读,更多相关《BS 6161-18-1991 Methods of test for anodic oxidation coatings on aluminium and its alloys - Determination of surface abrasion resistance《铝及铝合金阳极氧化镀层试验方法 第18部分 表面耐磨性测定》.pdf(8页珍藏版)》请在麦多课文档分享上搜索。
1、BRITISH STANDARD BS 6161-18: 1991 Methods of test for Anodic oxidation coatings on aluminium and its alloys Part 18: Determination of surface abrasion resistanceBS6161-18:1991 This British Standard, having been prepared under the directionof the Surface Coatings (other than Paints) Standards Policy
2、Committee, was published under the authority of the Standards Board and comes into effect on 20December1991 BSI 02-1999 The following BSI references relate to the work on this standard: Committee reference SRC/32 Draft for comment 91/50611 DC ISBN 0 580 20090 6 Committees responsible for this Britis
3、h Standard The preparation of this British Standard was entrusted by the Surface Coatings (other than Paints) Standards Policy Committee (SRC/-) to Technical Committee SRC/32, upon which the following bodies were represented: Aluminium Federation Aluminium Finishing Association Aluminium Window Asso
4、ciation Association of Builders Hardware Manufacturers British Lock Manufacturers Association British Metal Finishing Suppliers Association Institute of Corrosion Institute of Metal Finishing Institution of Chemical Engineers Metal Finishing Association Metal Window Federation Ltd. Amendments issued
5、 since publication Amd. No. Date CommentsBS 6161-18:1991 BSI 02-1999 i Contents Page Committees responsible Inside front cover Foreword ii 1 Scope 1 2 Definitions 1 3 Principle 1 4 Apparatus 1 5 Procedure 1 6 Test report 2 Figure 1 Position of abrasive paper on block 2 Publication(s) referred to Ins
6、ide back coverBS6161-18:1991 ii BSI 02-1999 Foreword This Part of BS6161 has been prepared under the direction of the Surface Coatings (other than Paints) Standards Policy Committee. At present the following Parts of this British Standard have been published: Part 1: Determination of mass per unit a
7、rea (surface density) of anodic oxidation coatings (gravimetric method); Part 2: Determination of thickness of anodic oxide coatings: non-destructive measurement by split-beam microscope; Part 3: Assessment of sealing quality by measurement of the loss of mass after immersion in phosphoric-chromic a
8、cid solution; Part 4: Assessment of sealing quality by measurement of the loss of mass after immersion in acid solution; Part 5: Estimation of loss of absorptive power of sealed coatings: dye spot test with prior acid treatment; Part 6: Assessment of sealing quality by measurement of admittance or i
9、mpedance; Part 7: Accelerated determination of light fastness of coloured anodic oxidation coatings using artificial light; Part 8: Determination of the fastness to ultraviolet light of coloured anodic oxide coatings; Part 9: Measurement of wear properties with an abrasive wheel wear test apparatus;
10、 Part 10: Measurement of mean specific abrasion resistance with an abrasive jet test apparatus; Part 11: Measurement of total reflectance using a photoelectric reflectometer; Part 12: Measurement of specular reflectance and specular gloss at angles of20,45,60 or85; Part 13: Image clarity test using
11、the Gardam grid; Part 14: Determination of infra-red reflectance; Part 15: Determination of electrical breakdown potential; Part 16: Rating system for the evaluation of pitting corrosion Chart method; Part 17: Rating system for the evaluation of pitting corrosion Grid method; Part 18: Determination
12、of surface abrasion resistance. Further Parts of this standard will be prepared, if required. This Part describes a method of test only and should not be used or quoted as a specification defining abrasion resistance. Reference to this Part should state that the method of test is in accordance with
13、the appropriate method(s) of BS6161-18. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. S
14、ummary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages1 and 2, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on theinside
15、front cover.BS 6161-18:1991 BSI 02-1999 1 1 Scope This Part of BS6161 describes a method of test for the determination of the surface abrasion resistance of anodic oxidation coatings produced either by sulphuric acid anodizing or by integral colour anodizing (in solutions containing high proportions
16、 of organic acids) on aluminium and its alloys. It is mainly intended for the evaluation of external architectural coatings. Whole articles can be used for this test and, for those passing the test, it is non-destructive. NOTE 1The abrasive wheel test and the abrasive jet test described in BS6161-9
17、and BS6161-10 respectively are, in contrast, destructive of the coating and often of the article. NOTE 2The titles of the publications referred to in this standard are listed on the inside back cover. 2 Definitions For the purposes of this Part of BS6161, the following definitions apply. 2.1 double
18、stroke one passage backwards and forwards across the test area on the test sample 2.2 test specimen the specimen on which the anodic oxidation coating is to be evaluated 2.3 block resilient support for the abrasive paper during the test 3 Principle The surface abrasion resistance is evaluated by usi
19、ng abrasive papers to determine whether or not the coating is harder than the abrasive papers used. 4 Apparatus 4.1 Glass coated paper, grade00 (very fine), as specified in BS871, strips12mm wide and150mm to200mm long. 4.2 Garnet coated paper, “A” weight, grade no.220, as specified in BS871, strips1
20、2mm wide and150mm to200mm long. NOTEThe hardness of the abrasives on Mohs scale are: glass4.0 to4.5 and garnet6.5 to6.8. 4.3 Resilient support for the paper during the test, 6mm to8mm thick and approximately30mm wide and40mm long. The hardness of the block shall be30IRHD to70IRHD (international rubb
21、er hardness degrees) as measured using the method described in BS903-A26. NOTEA large rectangular rubber or soft plastics pencil eraser may be suitable. 5 Procedure 5.1 Test specimen The test specimen shall normally consist of a production article (or part thereof). It shall be sealed, dry and clean
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS6161181991METHODSOFTESTFORANODICOXIDATIONCOATINGSONALUMINIUMANDITSALLOYSDETERMINATIONOFSURFACEABRASIONRESISTANCE

链接地址:http://www.mydoc123.com/p-545777.html