BS 5173-103 7-1991 Methods of test for rubber and plastics hoses and hose assemblies - Physical tests - Determination of fracture resistance of rigid polymer helical reinforcement .pdf

《BS 5173-103 7-1991 Methods of test for rubber and plastics hoses and hose assemblies - Physical tests - Determination of fracture resistance of rigid polymer helical reinforcement .pdf》由会员分享，可在线阅读，更多相关《BS 5173-103 7-1991 Methods of test for rubber and plastics hoses and hose assemblies - Physical tests - Determination of fracture resistance of rigid polymer helical reinforcement .pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS 5173-103.7: 1991 Methods of test for Rubber and plastics hoses and hose assemblies Part 103: Physical tests Section 103.7 Determination of fracture resistance of rigid polymer helical reinforcement in thermoplastics hosesBS5173-103.7:1991 This British Standard, having been prepar

2、ed under the directionof the Plastics and Rubber Standards Policy Committee, was published underthe authority of the BoardofBSI and comes intoeffecton 31January1991 BSI 07-1999 The following BSI references relate to the work on this standard: Committee reference PRM/66 Draft for comment 90/35198 DC

3、ISBN 0 580 19211 3 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the Plastics and Rubber Standards Policy Committee (PRM/-) to Technical Committee PRM/66, upon which the following bodies were represented: Association of Metropolitan Author

4、ities British Coal Corporation British Compressed Gases Association British Gas plc British Rubber Manufacturers Association Chief and Assistant Chief Fire Officers Association Energy Industries Council Fire Extinguishing Trades Association Home Office Institution of Fire Engineers Liquefied Petrole

5、um Gas Industry Technical Association (UK) London Fire and Civil Defence Authority London Regional Transport Malaysian Rubber Producers Research Association Ministry of Defence Society of Motor Manufacturers and Traders Limited The following bodies were also represented in the drafting of the standa

6、rd through subcommittees and panels: British Fluid Power Association Engineering Equipment and Materials Users Association Amendments issued since publication Amd. No. Date CommentsBS5173-103.7:1991 BSI 07-1999 i Contents Page Committees responsible Inside front cover Foreword ii 1 Scope 1 2 Apparat

7、us 1 3 Test pieces 1 4 Conditioning of test pieces 1 5 Procedure 1 6 Test report 1 Figure 1 Diagrammatic representation of reinforcement fracture test 2 Table 1 Block sizes for the fracture test 1 Publication(s) referred to Inside back coverBS5173-103.7:1991 ii BSI 07-1999 Foreword This Section of B

8、S5173 has been prepared under the direction of the Plastics and Rubber Standards Policy Committee. This Section supersedes clause10 of BS5173-3:1977 and completes the revision of BS5173-3:1977 which is withdrawn. The remainder of the 1976 and 1977 editions are to be revised and as each of the tests

9、is revised it is intended to issue it as a separate Part or Section of BS5173, as described in BS5173-100. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British St

10、andard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages1and2, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorpor

11、ated. This will be indicated in the amendment table on theinside front cover.BS5173-103.7:1991 BSI 07-1999 1 1 Scope This Section of BS5173 describes a method of test for the determination of the fracture resistance of the rigid polymer helical reinforcement in thermoplastics hoses. NOTEThe titles o

12、f the publications referred to in this standard are listed on the inside back cover. 2 Apparatus The apparatus consists of rectangular section lengths of hardwood or metal, having the specified block widths, appropriate to the bore size of the hose under test (seeTable 1). Table 1 Block sizes for th

13、e fracture test 3 Test pieces Each test piece shall be a ring of hose containing three helices of polymer reinforcement. This shall be split with a clean cut along its length. 4 Conditioning of test pieces No test shall be carried out within24h of manufacture. Test pieces shall be conditioned at sta

14、ndard laboratory temperature (23 2 C) for at least3h before testing. NOTEThe3h may be part of the 24h period. 5 Procedure Open up the test piece and place it over the block appropriate to its nominal bore. Leave it in this position seeFigure 1(a) for3362h. Reverse bend the test piece until the outer

15、 surfaces touch seeFigure 1(b) and examine for cracking or failure of the helices. 6 Test report The test report shall include the following information: a) the hose type and nominal bore; b) the date of manufacture and batch number or reference, if known; c) the method of manufacture and details of

16、 reinforcement; d) the number and date of this British Standard, i.e.BS5173-103.7:1991; e) the block width used; f) the period of test; g) whether or not fracture of the helices occurred and if so, the position and mode of failure for each test piece; h) the date of test. Nominal bore Block width 0.

17、2 mm mm mm 12.5 10 16 12 20 16 25 19 31.5 23 (38) 26 40 27 50 31 63 34 (75) 37 80 38 (88) 40 100 44 (112) 46 125 49 (127) 49 (137) 50 (153) 52 160 53 200 59 (203) 59 250 66 (305) 71 315 75 NOTENominal bores in parentheses are not preferred values.BS5173-103.7:1991 2 BSI 07-1999 Figure 1 Diagrammatic

18、 representation of reinforcement fracture testBS5173-103.7:1991 BSI 07-1999 Publication(s) referred to BS 5173, Methods of test for rubber and plastics hoses and hose assemblies 1) . BS 5173-100, General introduction. 1) Referred to in the foreword only.BS 5173-103.7: 1991 BSI 389 Chiswick High Road

19、 London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or re

20、vision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform t

21、he Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Bu

22、ying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as Br

23、itishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give d

24、etails on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact

25、Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the internationalstandardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract

26、 may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbol

27、s, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.