BS 4361-7-1988 Woodworking machines - Specification for thickness planing machines with rotary cutterblock for one-side dressing《木工机械 第7部分 单面刨光用带旋转组合铣刀的单面压刨床规范》.pdf

《BS 4361-7-1988 Woodworking machines - Specification for thickness planing machines with rotary cutterblock for one-side dressing《木工机械 第7部分 单面刨光用带旋转组合铣刀的单面压刨床规范》.pdf》由会员分享，可在线阅读，更多相关《BS 4361-7-1988 Woodworking machines - Specification for thickness planing machines with rotary cutterblock for one-side dressing《木工机械 第7部分 单面刨光用带旋转组合铣刀的单面压刨床规范》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS 4361-7: 1988 ISO 7568:1986 Woodworking machines Part 7: Specification for thickness planing machines with rotary cutterblock for one-side dressing ISO title: Woodworking machines Thickness planing machines with rotary cutterblock for one-side dressing Nomenclature and acceptance

2、conditions UDC 674.056:621.912.252BS4361-7:1988 This British Standard, having been prepared under the directionof the Machine, Engineers and Hand Tools Standards Committee, was published under the authority ofthe Board of BSI and comes intoeffect on 30 November 1988 BSI 12-1999 The following BSI ref

3、erences relate to the work on this standard: Committee reference MTE/23 Draft for comment 81/80431 DC ISBN 0 580 16742 9 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the Machine, Engineers and Hand Tools Standards Committee (MTE/-) to Tec

4、hnical Committee MTE/23 upon which the following bodies were represented: Advanced Manufacturing Technology Research Institute British Furniture Manufacturers Federation British Railways Board British Woodworking Federation Department of the Environment, Building Research Establishment (PrincesRisbo

5、rough Laboratory) Department of Trade and Industry, Mechanical Engineering and Manufacturing Technology Division (Mmt) Federation of British Hand Tool Manufacturers Furniture Industry Research Association Furniture, Timber and Allied Trades Union Health and Safety Executive Institute of Machine Wood

6、 Working Technology Ltd. National Sawmilling Association Saw Association Timber Research and Development Association Union of Construction, Allied Trades and Technicians Woodworking Machinery Suppliers Association Ltd. Amendments issued since publication Amd. No. Date of issue CommentsBS4361-7:1988

7、BSI 12-1999 i Contents Page Committees responsible Inside front cover National foreword ii 1 Scope and field of application 1 2 References 1 3 Preliminary remarks 1 4 Nomenclature 2 5 Acceptance conditions and permissible deviations Geometrical tests 4 Annex Equivalent terms 7 Publications referred

8、to Inside back coverBS4361-7:1988 ii BSI 12-1999 National foreword This Part of BS 4361 has been prepared under the direction of the Machine, Engineers and Hand Tools Standards Committee and implements agreements of the International Organization for Standardization (ISO). It is identical with ISO75

9、68:1986 “Woodworking machines Thickness planing machines with rotary cutterblock for one-side dressing Nomenclature and acceptance conditions”. Together with BS 4361-4 to BS 4361-6 and BS 4361-8 to BS 4361-12, this Part of BS4361 supersedes BS 4361-2:1968 which is withdrawn. Diagrams. For reasons of

10、 simplicity the diagrams in this standard illustrate only one type of machine. Terminology and conventions. The text of the International Standard has been approved as suitable for publication as a British Standard without deviation. Some terminology and certain conventions are not identical with th

11、ose used in British Standards; attention is drawn especially to the following. The comma has been used as a decimal marker. In British Standards it is current practice to use a full point on the baseline as the decimal marker. Wherever the words “this International Standard” appear, referring to thi

12、s standard, they should be read as “this Part of BS 4361”. In clauses1 and2 reference is made to ISO7984 for information only. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Complian

13、ce with a British Standard does not of itself confer immunity from legal obligations. Cross-references International Standard Corresponding British Standard ISO 230-1:1986 BS 3800:1964 Methods for testing the accuracy of machine tools (Technically equivalent) Summary of pages This document comprises

14、 a front cover, an inside front cover, pages i and ii, pages1 to 8, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BS4361-7:1988 BSI 12-1999 1

15、 1 Scope and field of application This International Standard specifies the appropriate terminology for each part of the machine and, with reference to ISO230-1, the geometrical tests for thickness planing machines with rotary cutterblock for one-side dressing; it also gives the corresponding permis

16、sible deviations which apply to machines of general purpose use and normal accuracy. NOTEIn addition to terms used in two of the three official ISO languages (English and French), this International Standard gives the equivalent terms in German, Spanish, Italian and Swedish in an Annex; these have b

17、een included at the request of Technical Committee ISO/TC 39 and are published under the responsibility of the member bodies for Germany, F.R. (DIN), Spain (IRANOR), Italy (UNI) and sweden (SIS). However, only the terms given in the official languages can be considered as ISO terms. This Internation

18、al Standard deals only with the verification of accuracy of the machine. It does not apply to testing the running of the machine (vibrations, abnormal noises, stick-slip motion of the components, etc.), nor to its characteristics speeds, feeds, etc.) which should generally be checked before testing

19、accuracy. This International Standard does not impose any practical test for thickness planing machines with rotary cutterblock for one-side dressing. Practical tests should be exceptions and have to be stated in a previous agreement between the manufacturer and the user. This International Standard

20、 applies to those machines designated by the number 12.212 in ISO 7984. 2 References ISO 230-1, Acceptance code for machine tools Part 1: Geometric accuracy of the machine operating under no load or finishing conditions. ISO 7984, Woodworking machines Technical classification of woodworking and auxi

21、liary machines 1) . 3 Preliminary remarks 3.1 In this International Standard all dimensions and permissible deviations are expressed in millimetres. 3.2 To apply this International Standard, reference should be made to ISO230-1, especially for installation of the machine before testing, the warming

22、up of the cutterblock and other moving parts, and description of measuring methods. The measuring instruments shall not permit errors over 1/3 of the tolerances being checked. 3.3 The sequence in which the geometrical tests are given is related to the sub-assemblies of the machine and this in no way

23、 defines the practical order of testing. In order to make the mounting of instruments or gauging easier, tests may be applied in any order. 3.4 It is not always possible nor necessary to carry out all the tests given in this International Standard. 3.5 It is up to the user to choose, in agreement wi

24、th the manufacturer, those tests relating to the properties which are of interest to him, but these tests shall be clearly stated when ordering a machine. 3.6 A movement is longitudinal when it takes place in the working direction of the piece. 3.7 When establishing the tolerance for a measuring ran

25、ge different from that given in this International Standard (see clause 2.311 in ISO230-1), it should be taken into consideration that the minimum value of the tolerance is 0,01mm. 1) At present at the stage of draft.BS4361-7:1988 2 BSI 12-1999 4 NomenclatureBS4361-7:1988 BSI 12-1999 3 Reference Eng

26、lish French Thickness planing machines withrotarycutterblock for one-side dressing Machines raboter sur une face avecoutilrotatif 1 Framework Ossature 1.1 Main frame Bti 2 Feed of workpiece and/or tools Dplacement des pices et/ou outils 2.1 Infeed feed roller Cylindre dentre 2.2 Outfeed feed roller

27、Cylindre de sortie 2.3 Table roller Cylindre de la table 2.4 Table extension roller Cylindre de la rallonge de table 2.5 Infeed roller drive sprocket Pignon du cylindre dentre 2.6 Outfeed roller drive sprocket Pignon du cylindre de sortie 2.7 Feed roller drive chain Chane dentranement des cylindres

28、dentre 2.8 Speed reduction gearbox Rducteur de vitesse 2.9 Variable speed gear Variateur de vitesse 2.10 Tensioning idler sprocket Pignon du tendeur de chane 3 Workpiece support clamp and guide Support, maintien et guidage des pices 3.1 Table Table 3.2 Chain transmission for table rise and fall move

29、ment Chane de transmission pour le rglage vertical et horizontal 3.3 Table extension Rallonge de table 3.4 Table elevating screw Vis de rglage vertical de la table 3.5 Infeed pressure bar Presseur dentre 3.6 Outfeed pressure bar Presseur de sortie 4 Tool-holders and tools Porte-outils et outils 4.1

30、Blades Lame 4.2 Cutterblock wedge Coin de blocage de la lame 4.3 Cutterblock Broche porte-outil 5 Workheads and tool drives Unit de travail et son entranement 5.1 Cutterblock bearing Palier de roulement 6 Controls Commandes 6.1 Starting switch Commutateur 6.2 Table vertical adjustment Rglage vertica

31、l de la table 6.3 Feed speed adjustment Variateur de vitesse 6.4 Feed engagement lever Dbrayage de lamene 6.5 Table roller adjustment Rouleaux de la table 6.6 Table vertical adjustment lock Verrouillage de la table 7 Safety devices Dispositifs de scurit 7.1 Anti-kick-back fingers Linguet antirecul 7

32、.2 Depth cut limiter Limiteur de passe 8 Miscellaneous Divers 8.1 Hood Capot 8.2 Access door to control gear Porte daccs aux organes mcaniques 8.3 Dust extraction outlet Buse daspiration 8.4 Scale for thicknessing Rgle micromtrique 9 (clause free) (chapitre libre) 10 Examples of work Exemples de tra

33、vail 10.1 Thicknessing RabotageBS 4361-7:1988 4 BSI 12-1999 5 Acceptance conditions and permissible deviations Geometrical tests No. Diagram Object Permissible deviations Measuring instruments Observations and references in ISO230-1 test code G1 Checking of flatness of the table: a) longitudinal str

34、aightness b) diagonal straightness c) transverse straightness a) and b) 0,20 for A u 1 000 0,30 for A 1 000 c) 0,10 for B u 400 0,15 for 400 1 000 Straightedge and feeler gauges Clauses 5.212 and 5.322 For checking c), measure intwo places each about 50mm on either side of thecutterblock. Flat to co

35、nvex. G2 Measuring of run-out of the table rollers 0,15 Dial gauge Clause 5.612.2 Checked at the ends and centre of each roller.BS 4361-7:1988 BSI 12-1999 5 No. Diagram Object Permissible deviations Measuring instruments Observations and references in ISO230-1 test code G3 Checking of parallelism of

36、 the table rollers to the table 0,10 for B u 400 0,15 400 1 000 Straight edge and dial gauge Clause 5.412.4 G4 Checking of parallelism of the table to the cutterblock in the upper and lower positions 0,10 for B u 400 0,15 for 400 1 000 Dial gauge Clause 5.412.4BS 4361-7:1988 6 BSI 12-1999 No. Diagra

37、m Object Permissible deviations Measuring instruments Observations and references in ISO230-1 test code G5 Measuring of run-out of the cutterblock 0,03 Dial gauge Clause 5.612.2 a) Where the blade setting device is carried from the block shoulders, check on the shoulders. b) Where the blade setting

38、device is carried from the cutterblock, check on the block.BS4361-7:1988 BSI 12-1999 7 Annex Equivalent terms Reference German Spanish Italian Swedish Dickenhobelmaschinemit Messerwellefreinseitige Bearbeitung Regruesadora Pialla a spessore Planhyvel 1 Stnder Armazn Incastellatura Stativkonstruktion

39、 1.1 Gestell Bastidor Basamento Stativ 2 Vorschub von Werkstck und/oder Werkzeug Desplazamiento de las piezas y/o de los tiles Spostamento dei pezzi e/o degli utensili Matning av arbetsstycke och/eller verktyg 2.1 Einzugswalze Rodillo de arrastre Rullo di entrata Inmatningsvals 2.2 Auszugswalze Rodi

40、llo de salida Rullo di uscita Utmatningsvals 2.3 Dickentischwalze Rodillo de la mesa Rullo sul piano Bordrulle 2.4 Sttzwalze in der Tischverlngerung Rodillo de la prolongacin dela mesa Rullo della prolunga delpiano Stdrulle p bordfrlngning 2.5 Kettenritzel der Einzugswalze Pin del rodillo de arrastr

41、e Pignone del rullo di entrata Kedjehjul fr inmatningsvals 2.6 Kettenritzel der Auszugswalze Pin del rodillo de salida Pignone del rullo di uscita Kedjehjul fr utmatningsvals 2.7 Antriebskette fr Vorschubwalzen Cadena de transmisin de losrodillos de arrastre Catena di azionamento dei rulli di avanza

42、mento Drivkedja fr matarvalsar 2.8 Geschwindigkeits- reduziergetriebe Caja reductora Riduttore di velocit Reduktionsvxel fr matningshastighet 2.9 Geschwindigkeits- nderungsgetriebe Variador de velocidad Variatore di velocit Stegls variator fr matningshastighet 2.10 Kettenspannrad Pin para tensin de

43、cadena Pignone tendicatena Kedjestrckarhjul 3 Werkstckauflage, -halterung und -fhrung Soporte, sujecin y gua de las piezas Supporto, fissaggio e guida dei pezzi Styrning av arbetsstycke 3.1 Tisch Mesa Piano Bord 3.2 Kettentrieb zur Hhenverstellung des Tisches Cadena de transmisin de elevacin de la m

44、esa Catena di trasmissione per regolazione verticale Kedjetransmission fr bordets hjdinstllning 3.3 Tischverlngerung Prolongacin de la mesa Prolunga del piano Bordfrlngning 3.4 Spindel fr die Hhenverstellung des Tisches Husillos de elevacin de la mesa Vite di regolazione del piano Skruv fr bordets h

45、jdinstllning 3.5 Einzugsdruckbalken Prensor de entrada Pressore di entrata Tryckbalk p inmatningssiden 3.6 Auszugsdruckbalken Prensor de salida Pressore di uscita Tryckbalk p utmatningssidan 4 Werkzeugtrger und Werkzeug Porta-til y tiles Portautensili ed utensili Verktygshllare och verktyg 4.1 Strei

46、fenhobelmesser Cuchillas Coltelli Kutterstl 4.2 Messerkeilleiste Cuas de blocaje de las cuchillas Lardoni conici di bloccaggio dei coltelli Kil fr fasthllning avkutterstl 4.3 Hobelmesserwelle Arbol porta-til Albero portacoltelli Kutterblock 5 Einbauteile und Teile fr den Werkzeugantrieb Unidad de tr

47、abajo y su transmisin Unit operatrice e esuoazionamento Bearbetningsenheter och drivsystem 5.1 Hobelmesserwellenlager Soporte del rodamiento Supporto dei cuscinetti Kutterlager 6 Bedienungs- und berwachungsorgane Mandos Comandi Manverorgen 6.1 Elektrischer Hauptschalter Conmutador Interruttore Start

48、don 6.2 Hhenverstellung des Tisches Mando de elevacin de la mesa Comando regolazione verticale Ratt fr bordinstllning 6.3 Verstellung der Vorschubgeschwindigkeit Mando del variador de velocidad Comando regolazione della velocit di avanzamento Reglage fr matningshastighetBS4361-7:1988 8 BSI 12-1999 R

49、eference German Spanish Italian Swedish Dickenhobelmaschinemit Messerwellefreinseitige Bearbeitung Regruesadora Pialla a spessore Planhyvel 6.4 Vorschubbettigung Mando de desembrague del arrastre Comando disinnesto dellavanzamento Kopplingspak fr matningen 6.5 Hhenverstellung der Dickentischwalzen Mando de regulacin del rodillo de la mesa Comando regolazione rulli del piano Instllningsdon fr bordrulle 6.6 Tischblockierung Mando de blo