BS 4215-15-1990 Resistance spot welding electrodes electrode holders and ancillary equipment - Specification for insulated pins for use in electrode back-ups《电阻点焊电极 焊钳和辅助设备 第15部分 电.pdf
《BS 4215-15-1990 Resistance spot welding electrodes electrode holders and ancillary equipment - Specification for insulated pins for use in electrode back-ups《电阻点焊电极 焊钳和辅助设备 第15部分 电.pdf》由会员分享,可在线阅读,更多相关《BS 4215-15-1990 Resistance spot welding electrodes electrode holders and ancillary equipment - Specification for insulated pins for use in electrode back-ups《电阻点焊电极 焊钳和辅助设备 第15部分 电.pdf(8页珍藏版)》请在麦多课文档分享上搜索。
1、BRITISH STANDARD BS4215-15: 1990 Incorporating Amendment No.1 Resistance spot welding electrodes, electrode holders and ancillary equipment Part15: Specification for insulated pins for use in electrode back-upsBS4215-15:1990 This British Standard, having been prepared under the directionof the Weldi
2、ng Standards Policy Committee, waspublished under the authorityof the Board of BSI andcomes into effect on 31December1990 BSI10-1999 The following BSI references relate to the work on this standard: Committee reference WEE/26 Draft for comment89/70856 DC ISBN 0 580 19095 1 Committees responsible for
3、 this British Standard The preparation of this British Standard was entrusted by the Welding Standards Policy Committee (WEE/-) to Technical Committee WEE/26, upon which the following bodies were represented: Association of Supervisory and Executive Engineers British Non-ferrous Metals Federation Br
4、itish Steel Industry Copper Development Association Electricity Supply Industry in England and Wales Health and Safety Executive Society of British Aerospace Companies Ltd. Society of Motor Manufacturers and Traders Ltd. Welding Institute Welding Manufacturers Association (BEAMA Ltd.) Coopted member
5、s Amendments issued since publication Amd. No. Date Comments 7132 July 1992 Indicated by a sideline in the marginBS4215-15:1990 BSI 10-1999 i Contents Page Committees responsible Inside front cover Foreword ii 1 Scope 1 2 References 1 3 Dimensions 1 4 Designation 1 5 Material 1 6 Finish 1 Figure 1 1
6、 Table 1 1 Publication(s) referred to Inside back coverBS4215-15:1990 ii BSI 10-1999 Foreword This Part of BS4215, prepared under the direction of the Welding Standards Policy Committee, is based on ISO9312:1990 “Resistance welding equipment Insulated pins for use in electrode back-ups” published by
7、 the International Organization for Standardization (ISO). It differs from the International Standard in specifying material that complies with BS4577 rather than ISO5182. The requirements for the softening temperature in BS4577 are generally more stringent than those in ISO5182. BS4215 is being rev
8、ised in several Parts and supersedes BS4215:1967, which has been withdrawn. Most of the Parts of BS4215 are or will be identical with or based on International Standards but, in instances where the United Kingdom was or is unable to give a vote of approval to the International Standard, a correspond
9、ing British Standard has been or will be prepared, where possible, taking into account the reasons for disapproval. A further Part will also be published in due course, specifying electrodes, electrode holders and ancillary equipment of interest in the UK only. The following Parts of BS4215 have bee
10、n published to date: Part1: Withdrawn (superseded by BS EN25183-1:1992 and BS EN25183-2:1992); Part2: Specification for straight resistance spot welding electrodes; Part3: Withdrawn (superseded by BS EN21089:1992); Part4: Withdrawn (superseded by BS EN25822:1992); Part5: Withdrawn (superseded by BS
11、EN25827:1992); Part6: Specification for electrode adaptors, female taper1:10; Part7: Specification for male electrode caps; Part8: Withdrawn (superseded by BS EN27931:1992); Part9: Withdrawn (superseded by BS EN25183-1:1992); Part10: Withdrawn (superseded by BS EN25183-2:1992); Part11: Withdrawn (su
12、perseded by BS EN28430-1:1992); Part12: Withdrawn (superseded by BS EN28430-2:1992); Part13: Withdrawn (superseded by BS EN28430-3:1992); Part14: Withdrawn (superseded by BS EN29313:1992); Part15: Specification for insulated pins for use in electrode back-ups. As this Part is based on ISO9312:1990,
13、some terminology and certain conventions are not identical with those used in British Standards. The Technical Committee has reviewed the provisions of ISO1642 for which there is no equivalent British Standard, and has decided that they are acceptable for use in conjunction with this Part of BS4215.
14、 A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises
15、 a front cover, an inside front cover, pagesi and ii, pages1 and 2, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BS4215-15:1990 BSI 10-1999
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS4215151990RESISTANCESPOTWELDINGELECTRODESELECTRODEHOLDERSANDANCILLARYEQUIPMENTSPECIFICATIONFORINSULATEDPINSFORUSEINELECTRODEBACKUPS

链接地址:http://www.mydoc123.com/p-544228.html