BS 2C 13-1988 Specification for sizes of aircraft gravity filling orifices and associated replenishment nozzles (metric series)《飞机重力灌注燃油口及相关供燃油嘴的尺寸规范(米制系列)》.pdf

《BS 2C 13-1988 Specification for sizes of aircraft gravity filling orifices and associated replenishment nozzles (metric series)《飞机重力灌注燃油口及相关供燃油嘴的尺寸规范(米制系列)》.pdf》由会员分享，可在线阅读，更多相关《BS 2C 13-1988 Specification for sizes of aircraft gravity filling orifices and associated replenishment nozzles (metric series)《飞机重力灌注燃油口及相关供燃油嘴的尺寸规范(米制系列)》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD AEROSPACE SERIES BS2C13:1988 (Superseding C13:1960) Specification for Sizes of aircraft gravity filling orifices and associated replenishment nozzles (metric series) UDC621.64:629.065BS2C13:1988 This BritishStandard, having been prepared under the directionof the Aerospace Standards

2、 Committee, was published under the authorityofthe Board of BSI and comes into effect on 29February1988 BSI01-2000 The following BSI references relate to the work on this standard: Committee referenceACE/14 Draft for comment87/71716DC ISBN 0 580 16461 6 Committees responsible for this British Standa

3、rd The preparation of this BritishStandard was entrusted by the Aerospace Standards Committee(ACE/-) to Technical Committee ACE/14 upon which the following bodies were represented: Civil Aviation Authority (Airworthiness Division) British Independent Steel Producers Association Federation of Wire Ro

4、pe Manufacturers of Great Britain Ministry of Defence Society of British Aerospace Companies Limited Stainless Steel Wire Export Group The Institute of Petroleum Amendments issued since publication Amd. No. Date of issue CommentsBS2C13:1988 BSI 01-2000 i Contents Page Committees responsible Inside f

5、ront cover Foreword ii 1 Scope 1 2 Dimensions of gravity filling orifices 1 3 Dimensions of replenishment nozzles 1 Table 1 Orifice diameters 1 Table 2 Fuel nozzle diameter 1 Publication referred to Inside back coverBS2C13:1988 ii BSI 01-2000 Foreword This BritishStandard, which has been prepared un

6、der the direction of the Aerospace Standards Committee, is a revision of BSC13:1960 which is withdrawn. Except for the orifice sizes relating to aviation gasoline (AVGAS), turbine fuel and synthetic lubricants, and the addition of dimensions for replenishment nozzles, it is technically equivalent to

7、 ISO102:1976, published by the International Organization for Standardization (ISO). The standard has been revised to introduce separate sizes of gravity filling orifices for synthetic and non-synthetic lubricants, and for aviation gasoline (AVGAS) and turbine fuel, the former having a diameter smal

8、ler than that for the latter. It also specifies the outside diameters of the associated fuel replenishment nozzles. The adoption of these requirements for fuel filling orifices will minimize the possibility of the incorrect replenishment of aviation gasoline powered aircraft with turbine fuel and it

9、s attendant disastrous consequences. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summ

10、ary of pages This document comprises a front cover, an inside front cover, pagesi andii, pages1 and2, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front

11、 cover.BS2C13:1988 BSI 01-2000 1 1 Scope This BritishStandard specifies the minimum and/or maximum internal diameters of orifices for the gravity filling of aircraft with fuel, lubricants and other liquids. It also specifies the outside diameters of associated replenishment nozzles, and in particula

12、r of those nozzles used for the gravity replenishment of aircraft with aviation gasoline (AVGAS) and turbine fuel. NOTE 1The titles of the publications referred to in this standard are listed on the inside back cover. NOTE 2The latest revision of an Aerospace Series standard is indicated by a prefix

13、 number. 2 Dimensions of gravity filling orifices The internal diameters of the orifices shall be as given in Table 1. Table 1 Orifice diameters 3 Dimensions of replenishment nozzles 3.1 Fuelling nozzles The external diameter of nozzles used for the gravity replenishment of aircraft with fuel shall

14、be as given in Table 2. 3.2 Other replenishment nozzles The outside diameters of nozzles used for the gravity replenishment of liquids other than fuel shall be such that the nozzles can be readily inserted into the relevant minimum orifice diameter given in Table 1. Table 2 Fuel nozzle diameter Fill

15、ing orifice Internal diameter Min. Max. Aviation gasoline (AVGAS) Turbine fuel Non-synthetic lubricants Synthetic lubricants De-icing fluids Drinking water Hydraulic fluids Coolant Engine refrigerants mm 55 75 50 38 44 44 38 38 38 mm 60 NOTEWhere a filter is fitted at any of the orifices stated in t

16、he table, it should not result in a reduction of the relevant minimum internal diameter. Fuel Nozzle external diameter Min. Max. Aviation gasoline (AVGAS) Turbine fuel mm 67 mm 49 702 blankBS2C13:1988 BSI 01-2000 Publication referred to ISO102, Aircraft Gravity filling orifices 1) . 1) Referred to i

17、n the foreword only.BS2C13:1988 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.

18、 Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or

19、 ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers

20、automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the

21、BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI elect

22、ronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of s

23、tandards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted u

24、nder the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of imp

25、lementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.