BS 2782-11 Method 1121C-1997 Methods of testing plastics - Thermoplastics pipes fittings and valves - Thermoplastics pipes for the conveyance of fluids - Nominal outside diameters .pdf

《BS 2782-11 Method 1121C-1997 Methods of testing plastics - Thermoplastics pipes fittings and valves - Thermoplastics pipes for the conveyance of fluids - Nominal outside diameters .pdf》由会员分享，可在线阅读，更多相关《BS 2782-11 Method 1121C-1997 Methods of testing plastics - Thermoplastics pipes fittings and valves - Thermoplastics pipes for the conveyance of fluids - Nominal outside diameters .pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS 2782-11: Method 1121C: 1997 ISO 161-2: 1996 Methods of testing Plastics Part 11: Thermoplastics pipes, fittings and valves Method 1121C Thermoplastics pipes for the conveyance of fluids Nominal outside diameters and nominal pressures Inch-based series ICS 23.040.20BS2782-11:Metho

2、d 1121C:1997 This British Standard, having been prepared under the directionof the Sector Board forMaterials and Chemicals, waspublished under the authorityof the Standards Boardand comes into effect on 15June 1997 BSI 09-1999 ISBN 0 580 27563 9 Amendments issued since publication Amd. No. Date Comm

3、entsBS2782-11:Method 1121C:1997 BSI 09-1999 i Contents Page National foreword ii Foreword iii Text of ISO 161-2 1BS2782-11:Method 1121C:1997 ii BSI 09-1999 National foreword This British Standard reproduces verbatim ISO 161-2:1996 and implements it as the UK national standard. This International Sta

4、ndard is incorporated into BS2782 Methods of testing plastics: Part 11: Thermoplastics pipes, fittings and valves, as Method1121C, for association with related test methods for plastics materials and plastics piping components. In this context, attention is drawn to BS2782-11:Method1121B:1997, which

5、 is the dual-numbered version of ISO161-1:1996 Thermoplastics pipes for the conveyance of fluids Nominal outside diameters and nominal pressures Part 1: Metric series. These standards are included among these test methods because they provide the basis for calculation of test pressure/wall stress re

6、lationships required by some of the other methods. This British Standard, together with BS ISO4065 and BS ISO11922-2 when available, will partially supersede BS3867:1987, which will become obsolescent and retained only to support existing British Standards. The UK participation in its preparation wa

7、s entrusted to Technical Committee PRI/61, Plastics piping systems and components, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interest

8、s informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred

9、 to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or using the “Find” facility of the BSI Standards Electronic Catalogue. WARNING NOTE This British Standard, which is identical with ISO161-2:1996, does not nece

10、ssarily detail all the precautions necessary to meet the requirements of the Health and Safety at Work etc. Act1974. Attention should be paid to any appropriate safety precautions and the method should be operated only by trained personnel. A British Standard does not purport to include all the nece

11、ssary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theIS

12、O title page, pages ii to iv, pages 1 to 4 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BS2782-11:Method 1121C:1997 ii BSI 09-1999 Contents Page Foreword iii Int

13、roduction 1 1 Scope 1 2 Normative references 1 3 Definitions 1 4 Nominal outside diameter, d n , and nominal size, DN 2 5 Nominal pressure rating, PN 3 6 Minimum required strength, MRS 3 Annex A (informative) Bibliography 4 Table 1 Permitted values of nominal outside diameter, d n , and nominal size

14、, DN 3 Table 2 Permitted values of nominal pressure rating, PN 3 Table 3 Permitted values of minimum required strength, MRS 3 Descriptors: Fluid pipelines, pipes (tubes), thermoplastic resins, plastic tubes, specifications, mechanical strength, pressure, dimensions, diameters, imperial system.BS2782

15、-11:Method 1121C:1997 BSI 09-1999 iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body

16、 interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotec

17、hnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75% of the member bodies casting a vote

18、. International Standard ISO161-2 was prepared by Technical Committee ISO/TC138, Plastics pipes, fittings and valves for the transport of fluids. This second edition cancels and replaces the first edition (ISO161-2:1977), which has been technically revised. ISO161 consists of the following parts, un

19、der the general title Thermoplastics pipes for the conveyance of fluids Nominal outside diameters and nominal pressures: Part 1: Metric series; Part 2: Inch-based series. Annex A of this part of ISO161 is for information only.iv blankBS2782-11:Method 1121C:1997 BSI 09-1999 1 Introduction In this par

20、t of ISO161, some of the abbreviations used have been derived from the French language and others from English. It has been agreed to maintain the same abbreviations in both the French and English versions of the document. For reference, the abbreviations are listed below with the originating langua

21、ge given first and the translation second: 1 Scope This part of ISO161 specifies the nominal outside diameters for inch-based thermoplastics pipes for the conveyance of fluids in pressure and non-pressure applications. It also specifies nominal pressure ratings, minimum required strengths and overal

22、l service (design) coefficients for thermoplastics pipes for pressure applications. It is applicable to smooth thermoplastics pipes of constant circular cross-section along the whole length of the pipe, whatever their method of manufacture or material of construction. 2 Normative references The foll

23、owing standards contain provisions which, through reference in this text, constitute provisions of this part of ISO161. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this part of ISO161 are encouraged to inves

24、tigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 3:1973, Preferred numbers Series of preferred numbers. ISO 12162:1995, Thermoplastics materials for pipes and fittin

25、gs for pressure applications Classification and designation Overall service (design) coefficient. 3 Definitions For the purposes of this part of ISO161, the following definitions apply. 3.1 nominal outside diameter, d n for inch-based series pipes conforming to this part of ISO161, the nominal outsi

26、de diameter serves as a reference outside diameter, expressed in millimetres, to which the permissible deviations are applied as positive and/or negative values 3.2 nominal size, DN an alphanumerical designation of size which is common to all components in a thermoplastics piping system other than f

27、langes and components designated by thread size. It is a convenient round number for reference purposes 3.3 Outside diameter, d e 3.3.1 mean outside diameter, d em the measured length of the outer circumference of the pipe divided by ; 1) , rounded up to the nearest0,1mm 3.3.2 minimum mean outside d

28、iameter, d em,min the minimum value of the mean outside diameter specified in the applicable pipe standard. It is equal to the nominal outside diameter d n , expressed in millimetres 3.4 Pressure 3.4.1 nominal pressure, PN an alphanumeric designation related to the mechanical characteristics of the

29、components of a piping system and used for reference purposes. It is a convenient number selected from the R10 series as defined in ISO3 3.4.2 maximum allowable operating pressure, p PMS the allowable pressure in the pipe when the overall service (design) coefficient C has been applied. It is expres

30、sed in megapascals PN: Pression nominale (F) Nominal pressure (E) PMS: Pression maximale de service (F) Maximum allowable operating pressure (E) MRS: Minimum required strength (E) Rsistance minimale requise (F) s : Design stress (E) Contrainte de calcul (F) 1) The value of ; is taken to be 3,142.BS2

31、782-11:Method 1121C:1997 2 BSI 09-1999 3.5 lower confidence limit, LCL a quantity with the dimensions of stress, in megapascals, which can be considered as a property of the material under consideration and represents the 97,5% lower confidence limit of the predicted long-term hydrostatic strength a

32、t 20 C for 50years with internal water pressure 3.6 minimum required strength, MRS the value of the lower confidence limit LCLrounded down to the next value in the R10 series as defined in ISO3 when LCLis less than 10MPa or down to the next value in the R20 series as defined in ISO3 when LCLis great

33、er than or equal to 10MPa. The MRS is expressed as a hoop stress in megapascals 3.7 overall service (design) coefficient, C an overall coefficient with a value greater than1, which takes into consideration service conditions as well as properties of the components of a piping system other than those

34、 represented in the lower confidence limit the minimum values of C for specified materials are given in ISO12162 3.8 design stress, s the allowable stress for a given application. It is derived by dividing the MRS by the overall service (design) coefficient C and rounding to the nearest lower value

35、in the R20 series as defined in ISO3,i.e. it is expressed in megapascals 3.9 standard dimension ratio, SDR the ratio of the nominal outside diameter of a pipe to its nominal wall thickness the SDR can be calculated from either of the following equations: or where for a given SDR, and using the value

36、s of MRS and C specified in the applicable product standard, the maximum allowable operating pressure p PMScan be calculated from either of the following equations: or 3.10 hydrostatic stress, the stress induced in the wall of a pipe when the pipe is filled with a fluid under pressure. The hydrostat

37、ic stress, expressed in megapascals, is related to the pressure, the wall thickness and the outside diameter of the pipe by the following equation: where 4 Nominal outside diameter, d n , and nominal size, DN The nominal outside diameter d nand nominal size DN shall be selected from the values given

38、 in Table 1. s MRS C - = MRS is the minimum required strength, in megapascals; p PMS is the maximum allowable operating pressure, in megapascals; C is the overall service (design) coefficient; s is the design stress, in megapascals. p is the hydrostatic pressure, in megapascals; d e is the outside d

39、iameter of the pipe, inmillimetres; e is the wall thickness of the pipe, inmillimetres.BS2782-11:Method 1121C:1997 BSI 09-1999 3 Table 1 Permitted values of nominal outside diameter, d n , and nominal size, DN 5 Nominal pressure rating, PN The nominal pressure rating PN shall be selected from the va

40、lues given inTable 2. Table 2 Permitted values of nominal pressure rating, PN (together with the corresponding values of the maximum allowable operating pressure p PMS ) 6 Minimum required strength, MRS The minimum required strength MRS shall be selected from the values given inTable 3. Table 3 Perm

41、itted values of minimum required strength, MRS d n DN d n DN d n DN 10,2 13,5 17,2 21,3 1/8 1/4 3/8 1/2 114,3 140,3 168,3 193,7 4 5 6 7 558,2 609,6 660,4 711,2 22 24 26 28 26,9 33,7 42,4 48,3 3/4 1 1 1/4 1 1/2 219,1 244,5 273 323,9 8 9 10 12 762 812,8 863,6 914,4 30 32 34 36 60,3 75,3 88,9 101,6 2 2

42、 1/2 3 3 1/2 355,6 406,4 457,2 508 14 16 18 20 1 016 40 PN p PMS bar MPa 1 2,5 3,2 4 1 2,5 3,2 4 0,1 0,25 0,32 0,4 5 6 6,3 8 5 6 6,3 8 0,5 0,6 0,63 0,8 10 12,5 16 20 10 12,5 16 20 1 1,25 1,6 2 NOTEIf higher nominal pressures are required, they shall be selected from the R5 or R10 series given in ISO

43、3. Values in megapascals 1 1,25 1,6 2 6,3 8 10 11,2 20 22,4 25 28 2,5 3,15 4 5 12,5 14 16 18 31,5 35,5 40 NOTEThe steps between the values from 1 to 10 are based on the R 10 series given in ISO 3 (25 % increments), whilst the steps between the values greater than 10 are based on the R 20 series (12

44、% increments).BS2782-11:Method 1121C:1997 4 BSI 09-1999 Annex A (informative) Bibliography 1 ISO 161-1:1996, Thermoplastics pipes for the conveyance of fluids Nominal outside diameters and nominal pressures Part 1: Metric series. 2 ISO 497:1973, Guide to the choice of series of preferred numbers and

45、 of series containing more rounded values of preferred numbers. 3 ISO 4065:1996, Thermoplastics pipes Universal wall thickness table.5 blankBS 2782-11: Method 1121C: 1997 ISO 161-2: 1996 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body resp

46、onsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendme

47、nts or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found

48、 on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications sho

49、uld be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also av