ASTM F2121-2005(2009) Standard Practice for Treestand Labels《Treestand标签的标准实施规程》.pdf

《ASTM F2121-2005(2009) Standard Practice for Treestand Labels《Treestand标签的标准实施规程》.pdf》由会员分享，可在线阅读，更多相关《ASTM F2121-2005(2009) Standard Practice for Treestand Labels《Treestand标签的标准实施规程》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F2121 05 (Reapproved 2009)An American National StandardStandard Practice forTreestand Labels1This standard is issued under the fixed designation F2121; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last r

2、evision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice provides guidance for providing userlabels on treestands.1.2 This standard does not purport to address all of

3、thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2F1749 Specification for F

4、itness Equipment and FitnessFacility Safety Signage and Labels3. Terminology3.1 The terminology and definitions in the referenced docu-ments are applicable to this practice.3.2 Definitions:3.2.1 backbar or V-barthe adjustable component of aclimbing treestand or handclimber that engages the tree topr

5、ovide support. The backbar may be rigid or flexible.3.2.2 climbing sticka device to assist climbing a treeprimarily to a fixed position treestand. A structure that issecured to the tree and allows the user to support his weightand climb to the desired height on the tree.3.2.3 climbing treestanda tre

6、estand that provides both themeans to ascend the tree, and allow the user to remain at adesired elevation.3.2.4 handclimber, or climbing aida device to assistclimbing with a climbing treestand. A structure that allows theuser to support his weight when lifting a climbing treestandwith his legs.3.2.5

7、 ladder treestanda treestand that is secured to thetree at the elevation where the platform is located. (The laddertreestand may be secured to the tree at other locations and hassteps that are used to reach the platform or hunting position).3.2.6 non-climbing, fixed position or hang-on treestandatre

8、estand that is secured to the tree at the elevation where it isused. (The user usually ascends the tree by some means andthen lifts the treestand to the desired position and secures it foruse.)3.2.7 platformthe horizontal structural area of a treestandon which the user stands and/or places his feet.

9、3.2.8 treestanda device designed to be affixed to a tree orits branches so as to permit an individual to sit or stand thereonfor the purpose of attaining an elevated position from which toobserve, photograph or hunt.3.2.9 tripod or tower standa tripod or tower stand isconstructed to be self-supporti

10、ng and is not required to besecured to a tree.4. Summary of Practice4.1 This practice provides guidelines for the design andplacement of user labels and warnings on treestands andclimbing sticks, particularly for quality assurance and ad-equacy of safety including:4.1.1 Use of instructions in antici

11、pation of user error ormisuse.4.1.2 Rated load capacity in accordance with manufactur-ers rating.4.1.3 Availability of instructions in case of their loss.4.1.4 Placement of labels and warnings.4.1.5 Types of labels.4.1.6 Special labels and warnings.5. Significance and Use5.1 This practice is provide

12、d to develop and maintainuniformity in practices for use, selection, location, placement,and content of labels on treestands and climbing sticks,particularly with regard to quality assurance and safety.5.2 It is emphasized that the use of these practices will notalter the validity of data determined

13、 with specific tests, butprovides guidance in the interpretation of test results (valid or1This practice is under the jurisdiction of ASTM Committee F08 on SportsEquipment and Facilities and is the direct responsibility of Subcommittee F08.16 onArchery Products.Current edition approved Sept. 1, 2009

14、. Published February 2010. Originallyapproved in 2001. Last previous edition approved in 2005 as F2121 05. DOI:10.1520/F2121-05R09.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume informa

15、tion, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.invalid) and guidance in the selection of a reasonable generalprovision in those instances where no standard exists

16、 today.6. Procedure6.1 It is recommended that manufacturers follow the meth-ods of labeling in Specification F1749 and so described herein.When unusual or special conditions require labels or warningmethods not covered herein, the manufacturer shall be respon-sible for their development to assure ad

17、equate information forthe user.6.2 All labels and warnings shall be clearly understandable,legible, in English, of a size consistent with the space availableto be marked, and able to withstand reasonable exposure to theelements.6.3 Selection of Placement:6.3.1 Labels and warnings shall be placed suc

18、h that they arevisible to the user when mounting the treestand or climbingstick and when it is in use (sitting or standing). The followingplacement locations are recommended for individual units andsituations:6.3.1.1 The top (upper) side of the platform as given in3.2.7.6.3.1.2 Along the top (upper)

19、 side of the backbar as given in3.2.1.6.3.1.3 Along the top (upper) side of a flat surface on a mainstructural support member.6.3.1.4 On the top (upper) portion of a component requiringa special label or warning.6.4 Selection of Type of Label or Warning:6.4.1 All materials used shall be able to with

20、stand reason-able exposure to the elements.6.4.1.1 For direct mark use, it shall be with permanent ink orpaint, engraved, stamped, embossed, etched or other permanentmeans.6.4.1.2 For tagging (nameplates, stickers, etc.), the tag shallbe secured by mechanical means or by adhesives suitable towithsta

21、nd reasonable exposure to the elements.Adhesives shallbe resistant to peel off.6.4.1.3 Labels and/or lettering shall be highly visible by useof contrasting and/or bright colors. For example, safety (bright)yellow test on dark background.6.5 Label Content:6.5.1 The minimum information that shall be p

22、rovided on atreestand label is as follows:6.5.1.1 The warning must contain a signal word to alert theuser to potential hazards such as injury or death. The signalword must be “warning,” “caution,” or “danger.”6.5.1.2 The label must contain a phrase that warns to “notuse without a full body harness”

23、or “always wear a full bodyharness.”6.5.1.3 The label must contain a phrase that warns to “notuse before reading instructions” or “read instructions beforeuse.”6.5.1.4 The label must state the rated load capacity orweight limit of the treestand.6.5.1.5 The label must contain the manufacturers name a

24、ndaddress or name and telephone number.6.5.1.6 Any specific safety information pertinent to a par-ticular model should be printed on the label.6.5.2 It is highly recommended that the label as given in6.5.1.2 be preceded with the word “Warning.”6.5.3 Other information that should be helpful to the us

25、er asa label, but could be contained in the instructions is recom-mended. Example phrases are: “do not modify this product”and “proper maintenance and inspection is required.”7. Keywords7.1 backbar; climbing aid; climbing stick; platform; tree-stand; tripodAPPENDIX(Nonmandatory Information)X1. Addit

26、ional InformationX1.1 This practice is provided for use by manufacturers oftreestands and testing companies. Criteria has been developedfor certification of treestands and this practice is an integralpart of the certification. However, a treestand conforming tothis practice alone does not constitute

27、 certification and thosemanufacturers desiring certification must meet all applicablestandards as a minimum requirement.F2121 05 (2009)2ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this stan

28、dard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and

29、if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, w

30、hich you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959

31、,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).F2121 05 (2009)3