ASTM F2118-2003 Test Method for Constant Amplitude of Force Controlled Fatigue Testing of Acrylic Bone Cement Materials《聚丙烯骨用水泥材料力控疲劳试验的恒定幅值的试验方法》.pdf

《ASTM F2118-2003 Test Method for Constant Amplitude of Force Controlled Fatigue Testing of Acrylic Bone Cement Materials《聚丙烯骨用水泥材料力控疲劳试验的恒定幅值的试验方法》.pdf》由会员分享，可在线阅读，更多相关《ASTM F2118-2003 Test Method for Constant Amplitude of Force Controlled Fatigue Testing of Acrylic Bone Cement Materials《聚丙烯骨用水泥材料力控疲劳试验的恒定幅值的试验方法》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F 2118 03Standard Test Method forConstant Amplitude of Force Controlled Fatigue Testing ofAcrylic Bone Cement Materials1This standard is issued under the fixed designation F 2118; the number immediately following the designation indicates the year oforiginal adoption or, in the case of

2、revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method describes test procedures for evaluat-ing the constant amplitude, uniaxial, te

3、nsion-compression uni-form fatigue performance of acrylic bone cement materials.1.2 This test method is relevant to orthopaedic bone ce-ments based on acrylic resins, as specified in SpecificationF 451. The procedures in this test method may or may notapply to other surgical cement materials.1.3 It

4、is not the intention of this test method to define levelsof performance of these materials. Furthermore, it is not theintention of this test method to directly simulate the clinical useof these materials.1.4 A rationale is given in Appendix X1.1.5 The values stated in SI units are to be regarded as

5、thestandard.1.6 This standard does not purport to address all of thesafety concerns associated with its use. It is the responsibilityof the user of this standard to consult and establish appropriatesafety and health practices and determine the applicability ofregulatory limitations prior to use.2. R

6、eferenced Documents2.1 ASTM Standards:E 466 Practice for Conducting Force Controlled ConstantAmplitude Axial Fatigue Tests of Metallic Materials2E 467 Practice for Verification of Constant Amplitude Dy-namic Forces in an Axial Fatigue Testing System2E 1823 Terminology Relating to Fatigue and Fractur

7、e Test-ing2F 451 Standard Specification for Acrylic Bone Cement32.2 ISO Standard:ISO 7206-8 Implants for Surgery, Partial and Total Hip JointProstheses, Part 8Endurance Performance of StemmedFemoral Components with Application of Torsion43. Terminology3.1 Unless otherwise given, the definitions for

8、fatigue ter-minology given in Terminology E 1823 will be used.3.2 median fatigue strength at N cyclesThe maximumstress at which 50 % of the specimens of a given sample wouldbe expected to survive N loading cycles. For the purposes ofthis test method, the fatigue strength will be determined at 5milli

9、on load cycles. A rationale for this is provided in theAppendix X1.4.3.3 runoutA predetermined number of cycles at which thetesting on a particular specimen will be stopped, and no furthertesting on that specimen will be performed. For the purposes ofthis test method, the runout will be 5 million lo

10、ad cycles.3.4 stress levelThe value of stress at which a series ofduplicate tests are performed. For the purposes of this testmethod, the stress level is reported as the maximum stressapplied to the specimen.3.5 specimen failureThe condition at which the specimencompletely breaks or is damaged to su

11、ch an extent that the loadframe is no longer able to apply the intended stress within therequired limits.4. Summary of Test Method4.1 Uniform cylindrical reduced gage section test specimensare manufactured from acrylic bone cement and mounted in auniaxial fatigue frame. The specimen is subjected to

12、fullyreversed tensile and compressive loading in a sinusoidal cyclicmanner at a specified frequency in phosphate buffered saline(PBS). The fatigue loading is continued until the specimen failsor a predetermined number of cycles (runout limit) is reached.5. Significance and Use5.1 This test method de

13、scribes a uniaxial, constant ampli-tude, fully reversed fatigue test to characterize the fatigueperformance of a uniform cylindrical waisted specimen manu-factured from acrylic bone cement.1This test method is under the jurisdiction of ASTM Committee F04 on Medicaland Surgical Materials and Devices

14、and is the direct responsibility of SubcommitteeF04.15 on Material Test Methods.Current edition approved Sept. 10, 2003. Published October 2003. Originallyapproved in 2001. Last previous edition approved in 2001 as F2118 - 01a.2Annual Book of ASTM Standards, Vol 03.01.3Annual Book of ASTM Standards,

15、 Vol 13.01.4Available from American National Standards Institute, 25 W. 43rd St, 4th Floor,New York, NY 10036.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5.2 This test method considers two approaches to evaluatingthe fatigue perf

16、ormance of bone cement:5.2.1 Testing is conducted at three stress levels to charac-terize the general fatigue behavior of a cement over a range ofstresses. The stress level and resultant cycles to failure of thespecimens are plotted on an S-N diagram.5.2.2 Another approach is to determine the fatigu

17、e strengthof a particular cement. The fatigue strength for orthopaedicbone cement is to be determined at 5 million (5 3 106) cycles.The “two-point method” is the specified procedure for con-ducting fatigue testing to determine fatigue strength 1.5.3 This test method does not define or suggest requir

18、edlevels of performance of bone cement. This fatigue test methodis not intended to represent the clinical use of orthopaedic bonecement, but rather to characterize the material using standardand well-established methods. The user is cautioned to con-sider the appropriateness of this test method in v

19、iew of thematerial being tested and its potential application.5.4 It is widely reported that multiple clinical factors affectthe fatigue performance of orthopaedic bone cement; however,the actual mechanisms involved are not well understood.Clinical factors which may affect the performance of bonecem

20、ent include: temperature and humidity, mixing method,time of application, surgical technique, bone preparation,implant design, and patient factors, among others. This testmethod does not specifically address these clinical factors. Thetest method can be used to compare different acrylic bonecement f

21、ormulations and products and different mixing meth-ods and environments (that is, mixing temperature, vacuum,centrifugation, and so forth).6. Apparatus6.1 Uniaxial Load FrameA testing machine capable ofapplying cyclic sinusoidal tensile and compressive loads.6.1.1 The crossheads of the load frame sh

22、all be aligned suchthat the alignment meets the requirements of 8.2 of PracticeE 466. The alignment should be checked at both the maximumtensile and minimum compressive load to be applied during thecourse of a test program.6.2 Cycle CounterA device capable of counting the num-ber of loading cycles a

23、pplied to a specimen during the courseof a fatigue test.6.3 Load CellA load cell capable of measuring dynamictensile and compressive loads in accordance with PracticeE 467.6.4 LimitA device capable of detecting when a testparameter (for example, load magnitude, actuator displace-ment, DC error, and

24、so forth) reaches a limiting value, at whichtime the test is stopped and the current cycle count recorded.6.5 Environmental ChamberA chamber designed to im-merse the fatigue specimen completely in a solution. Thechamber should have provisions for maintaining a constanttemperature to an accuracy of 6

25、2C.7. Test Specimen7.1 Test specimens shall be fabricated from cement that isrepresentative of the final product with regard to materials,manufacturing processes, sterilization, and packaging. Steril-ization methods have been shown to have an effect on fatigueperformance. Any deviations of the test

26、cement from theclinically used product must be reported.7.2 Cylindrical reduced gage section test specimens with astraight 5-mm diameter by 10-mm-long gage section shall beused. The diameter of the specimen ends shall be substantiallygreater than the gage diameter to ensure that fracture occurs inth

27、e gage section. A smooth radius or taper between thespecimen ends and gage section is suggested to ensure the gagesection is subjected to a uniform stress field. Suggestedspecimen dimensions are provided in Fig. 1.8. Specimen Preparation8.1 Cement MixingFIG. 1 Specimen DimensionsF21180328.1.1 Store

28、the liquid and powder portions of the cementaccording to the manufacturers instructions before mixing.8.1.2 Allow the mixing equipment to equilibrate to roomtemperature before mixing. Record the room temperature at theonset of mixing.8.1.3 Mix the powder and liquid components according tothe manufac

29、turers instructions and begin recording the timefrom this point using a stopwatch. Report any deviations fromthe manufacturers storage and mixing recommendations.8.1.4 Report the mixing method and any equipment used.The method used for mixing the cement may affect its fatiguebehavior. See X1.13 for

30、further information.8.2 Specimen FabricationThe cylindrical reduced gagesection test specimens are fabricated using one of two methods:8.2.1 Direct Molding:8.2.1.1 Insert the mixed cement into a specimen mold(manufactured from silicone, aluminum, TFE-fluorocarbon, orother suitable material) with an

31、internal cavity which has thesame dimensions as the final cement test specimen. Close themold. Record the method of cement insertion into the mold(that is, pour or inject) and method used to close the mold.8.2.1.2 Place the mold in a container of phosphate bufferedsaline (PBS). The PBS solution shou

32、ld be maintained at 37 62C. After the specimens have polymerized for at least 1 h, thespecimens may be removed from the mold. Appendix X2describes a suggested procedure for molding cement speci-mens.8.2.2 Machining:8.2.2.1 Insert the mixed cement into cylindrical mold(manufactured from aluminum, gla

33、ss, or TFE-fluorocarbontube). The inside diameter of the molding tube should be a fewmillimetres greater than the final specimen grip diameter.8.2.2.2 Maintain the temperature of the mold at at 37 62C. After the specimens have polymerized for at least 1 h, thespecimens may be removed from the mold.8

34、.2.2.3 Machining should not be performed until at least 24h after initial mixing to ensure that the cement is completelypolymerized.8.3 Specimen Examination:8.3.1 Radiographically examine the fabricated specimensfor internal defects. Visually examine specimens for surfacedefects. Defects in the gage

35、 or transition sections (radii) shallbe rejected from testing and discarded. A surface defect isdefined as a surface discontinuity greater than 250 m in majordiameter. In addition, the specimens shall be examined radio-graphically in two orthogonal planes. Specimens with internaldefects greater than

36、 1 mm in major diameter in the gage sectionshall be rejected from testing and discarded. The total numberof specimens rejected divided by the total number of specimensmanufactured (rejection rate) shall be reported. A rationale forthese rejection criteria is provided in X1.11.NOTE 1The development o

37、f fabrication defects may be related to thetendency of a material to develop porosity during polymerization. Theamount of porosity or fabrication defects in the test specimens may be acharacteristic of the cement being evaluated. The rejection rate may givea general indication of a materials tendenc

38、y toward porosity formation.8.4 Specimen FinishingIf necessary, lightly polish thegage length of the specimens with 600-grit abrasive paper inthe longitudinal direction until the surface is free of machiningand/or mold marks.8.5 Specimen MeasurementMeasure the diameter of thespecimens at a minimum o

39、f three places along the gage lengthof each specimen. The average of these measurements shall beused as the specimens gage diameter for calculation of therequired load.8.6 Specimen Conditioning:8.6.1 Place the test specimens in PBS which is maintained ata temperature of 37 6 2C.8.6.2 Maintain the sp

40、ecimens in the PBS solution for aminimum of 7 days. The cement specimens shall be maintainedin the PBS solution for 7 to 60 days. The specimens shall becontinually immersed in the test solution so that they do not dryout. Distilled water shall be added to the soaking chamberduring the soaking period

41、 to make up for evaporation loss.Each specimen should be soaked up to the time immediatelybefore its being mounted on the load frame. See X1.5 forfurther information.9. Fatigue Test Procedures9.1 Mount the specimens in a test frame test such that auniaxial load is applied. Collets, Jacobs chucks, or

42、 pressurizedgrips should be used to firmly grip the specimen at each end.Ensure the longitudinal centerline of the test specimens arealigned with test machine loading axis such that no bendingmoment may be applied to the specimens.9.2 Mount an environmental chamber on the load frame andfill with fre

43、sh test solution immediately after the specimen ismounted to keep the specimen from drying out. The chambershould be filled to a level such that the entire specimen isimmersed. Distilled water shall be added to the test chamberduring the course of a test to make up for evaporation loss. Thetemperatu

44、re controller should be programmed and activated toheat the test solution to 37C, and then maintain that tempera-ture within 62C. Fatigue testing should not begin until at least12 h after the solution temperature has reached 37C to ensureequilibration.9.3 Program the test frame controller to apply a

45、 fullyreversed sinusoidal cyclic waveform at a constant frequency.When testing at frequencies above 2 Hz, the user should verifythat, for the formulation being tested, the chosen frequency hasa negligible effect on the test results. See X1.6 for furtherinformation.9.4 Program the test frame controll

46、er to apply the desiredmaximum stress level and a stress ratio of R = 1, indicatingfully reversed loading. A rationale for using fully reversedloading is provided in Appendix X1.10. The load shall becalculated by multiplying the desired stress by the specimenscross-section area, based on each specim

47、ens gage diameterdetermined in 8.5.9.4.1 Report the stress level to the nearest 0.5 MPa.9.4.2 When developing an S-N curve, it is recommendedthat testing be conducted at the following maximum stresslevels: 15, 12.5, and 10 MPa. Other stress levels may also beappropriate. See X1.7 for a rationale reg

48、arding the selection ofthe recommended stress levels.F21180339.4.3 When determining a fatigue strength, the stress levelsshall be chosen in accordance with the “two-point method” 1.9.5 Number of SpecimensWhen developing an S-N curve,a minimum of fifteen specimens shall be tested at each stresslevel.

49、 The desired statistical power of the comparison and thevariability to be expected from the cement formulation(s) beinginvestigated should be considered when determining the ap-propriate sample size. See X1.12 for further information.9.5.1 When determining a fatigue strength, the number ofspecimens shall be chosen in accordance with the “two-pointmethod” 1.9.6 After the solution has reached the temperature require-ments in 9.2, activate the test frame controller to begin the test.9.7 Set the cycle counter and limit settings of the test framecontroll