ASTM F2034-2008 Standard Specification for Sheet Linoleum Floor Covering《层状铺地板油毡的标准规范》.pdf
《ASTM F2034-2008 Standard Specification for Sheet Linoleum Floor Covering《层状铺地板油毡的标准规范》.pdf》由会员分享,可在线阅读,更多相关《ASTM F2034-2008 Standard Specification for Sheet Linoleum Floor Covering《层状铺地板油毡的标准规范》.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: F 2034 08Standard Specification forSheet Linoleum Floor Covering1This standard is issued under the fixed designation F 2034; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parent
2、heses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers sheet linoleum floor covering.1.2 Three types of linoleum floor covering are covered (seeSection 4). These floor coverings ar
3、e intended for use incommercial, light commercial, and residential buildings basedon serviceability characteristics. General information and per-formance characteristics, which determine serviceability andrecommended use, are included in this specification.1.3 The values stated in inch-pound units a
4、re to be regardedas the standard; the values in parentheses are provided forinformation only.1.4 The following safety hazards caveat pertains only to thetest methods portion, Section 11, of this specification. Thisstandard does not purport to address all of the safety concerns,if any, associated wit
5、h its use. It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and to determine the applicability of regulatorylimitations prior to use.2. Referenced Documents2.1 ASTM Standards:2F 137 Test Method for Flexibility of Resilient FlooringMaterials wit
6、h Cylindrical Mandrel ApparatusF 141 Terminology Relating to Resilient Floor CoveringsF 150 Test Method for Electrical Resistance of Conductiveand Static Dissipative Resilient FlooringF 386 Test Method for Thickness of Resilient FlooringMaterials Having Flat SurfacesF 410 Test Method for Wear Layer
7、Thickness of ResilientFloor Coverings by Optical MeasurementF 710 Practice for Preparing Concrete Floors to ReceiveResilient FlooringF 925 Test Method for Resistance to Chemicals of ResilientFlooringF 970 Test Method for Static Load LimitF 1482 Practice for Installation and Preparation of PanelType
8、Underlayments to Receive Resilient FlooringF 1514 Test Method for Measuring Heat Stability of Resil-ient Flooring by Color ChangeF 1515 Test Method for Measuring Light Stability of Resil-ient Flooring by Color ChangeF 1516 Practice for Sealing Seams of Resilient FlooringProducts by the Heat Weld Met
9、hod (when Recommended)2.2 European Norms:EN 670 Identification and Composition of LinoleumDetermination of Cement and Ash Residue32.3 American National Standard:ANSI/ASQC Z1.4 Sampling Procedures and Tables forInspection by Attributes43. Terminology3.1 Definitions:3.1.1 For definitions, refer to Ter
10、minology F 141.4. Classification4.1 The floor coverings shall be of the following types:Type I Linoleum sheet with backingType II Static dissipative linoleum sheet with backingType III Linoleum sheet with special backing5. Ordering Information5.1 Linoleum sheet shall be ordered by type, class, thick
11、-ness, and other characteristics important to the purchaser forthe intended use.5.1.1 Title, number, and date of this specification.5.1.2 Type, class, and pattern number.5.1.3 Quantity in square yards (square metres).5.1.4 Thickness required (see Section 8).5.1.5 Sampling if other than as specified
12、in ANSI/ASQCZ1.4, level S-1, as noted in Table 1.5.1.6 Packing requirement if other than specified (see Sec-tion 14).5.1.7 Marking required if other than specified (see Section14).5.1.8 For specific chemical resistance (see 11.3).1This specification is under the jurisdiction of ASTM Committee F06 on
13、Resilient Floor Coverings and is the direct responsibility of F06.80 on Specifica-tions.Current edition approved Nov. 1, 2008. Published December 2008. Originallyapproved in 2000. Last previous edition approved in 2003 as F 2034031.2For referenced ASTM standards, visit the ASTM website, www.astm.org
14、, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from CEN European Committee for StandardizationCentral Sec-retariat: rue de Stassart, 36 B-1050, Brussels.4Available f
15、rom American National Standards Institute, 11 West 42ndSt., 13thFloor, New York, NY 10036.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5.1.9 Other requirements.6. Material6.1 Wear SurfaceThe wear surface is the portion abovethe fi
16、brous or suitable backing/bedding layer or base coat. Thewear surface should have a minimum thickness of 0.04 in. (1mm).6.1.1 Type I / Type II / Type IIIFor all types, the wearsurface of the linoleum shall consist of a homogeneous mixtureof linseed oil or vegetable drying oils, or both; rosin, woodf
17、lour, or cork flour, or a combination thereof; color pigments;and inorganic filler. For Type II, the linoleum shall haveincorporated into the wearing surface additives, which willgive the linoleum electrostatic discharge controlling properties.6.2 Backings:6.2.1 JuteThe jute backing shall be firmly
18、bonded to andpartially embedded in the linoleum mix.6.2.2 Special BackingIn some cases a special backing isadded such as cork, polyolefin, or other suitable backing.6.3 CompositionThe minimum amount of linoleum ce-ment shall be 30 % when tested in accordance with EuropeanNorm 670.7. Performance Requ
19、irements7.1 Linoleum sheet floor covering shall meet the require-ments in Table 1.8. Dimensions8.1 Linoleum sheet flooring is available in standard widthsof 79 in. (2 m) and typical lengths of 65 ft (20 m) to 105 ft (32m). Other widths and lengths may be available.8.2 Linoleum sheet is available in
20、standard thicknesses of0.080 in. (2.0 mm), 0.100 in. (2.5 mm), 0.125 in. (3.2 mm), and0.160 in. (4.0 mm). Other gages may be available.9. Workmanship, Finish and Appearance9.1 Materials furnished under this specification shall be anacceptable match to an approved sample(s) in pattern, color,and surf
21、ace appearance. The product shall be free of defectsthat would adversely affect performance or appearance.9.2 Drying room yellowing will disappear when the lino-leum is exposed to either natural or artificial light to give astable color in service; it may reappear or not disappear in areasnot expose
22、d to light.10. Sampling10.1 Sampling for testing physical characteristics listed inTable 2 shall be done in accordance with the provisions setforth in ANSI/ASQC Z1.4. The inspection level shall bespecial inspection level S-1 as noted in Table I, and theacceptance quality level (AQL) shall be 6.5 def
23、ects perhundred units as noted in Table II-A, or as specified in 10.2.10.2 Sampling for testing physical characteristics listedshall be done in accordance with provisions set forth inANSI/ASQC Z1.4. The inspection level shall be specialinspection level S-1 as noted in Table I, and the acceptancequal
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMF20342008STANDARDSPECIFICATIONFORSHEETLINOLEUMFLOORCOVERING 层状 铺地板 油毡 标准规范 PDF

链接地址:http://www.mydoc123.com/p-536361.html