ASTM F2010-2000(2005) Standard Test Method for Evaluation of Glove Effects on Wearer Hand Dexterity Using a Modified Pegboard Test《用改进的有孔板试验评定手套对穿戴者手灵活性影响的标准试验方法》.pdf
《ASTM F2010-2000(2005) Standard Test Method for Evaluation of Glove Effects on Wearer Hand Dexterity Using a Modified Pegboard Test《用改进的有孔板试验评定手套对穿戴者手灵活性影响的标准试验方法》.pdf》由会员分享,可在线阅读,更多相关《ASTM F2010-2000(2005) Standard Test Method for Evaluation of Glove Effects on Wearer Hand Dexterity Using a Modified Pegboard Test《用改进的有孔板试验评定手套对穿戴者手灵活性影响的标准试验方法》.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: F 2010 00 (Reapproved 2005)Standard Test Method forEvaluation of Glove Effects on Wearer Hand Dexterity Usinga Modified Pegboard Test1This standard is issued under the fixed designation F 2010; the number immediately following the designation indicates the year oforiginal adoption or, i
2、n the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method is used for evaluating hand dexteritywhile wearing gloves.1.1.1
3、This test method covers procedures in which thewearer picks up small objects between the thumb and indexfinger.1.2 This test method is suitable for evaluating gloves andother forms of hand protection that allow the wearer to pick upsmall objects between their thumb and index finger.1.3 This test met
4、hod does not address all effects of glove useon hand function. Other methods should be considered toevaluate the effects of gloves on grip, tactility, and other handfunctions of interest.NOTE 1This test method may not apply to all glove types orapplications.1.4 The values stated in SI units or in ot
5、her units shall beregarded separately as standard. The values stated in eachsystem must be used independently of the other, withoutcombining values in any way.1.5 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user
6、 of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2F 1494 Terminology Related to Protective Clothing3. Terminology3.1 Definitions:3.1.1 dexterity, na hand function
7、referring to the ability ofthe individual to manipulate objects with their hands.3.1.1.1 DiscussionDexterity may be classified as requir-ing fine motor skills in which relatively small objects aremanipulated or those involving gross motor skills in whichrelatively large objects are handled.3.1.2 glo
8、ve, nan item of protective clothing designed andconstructed for protecting the hand and wrist.3.1.3 hand function, nthe relative motion and manipula-tive abilities of the hand.3.1.3.1 DiscussionIn this test method, the effect of gloveson a specific hand function, dexterity, is evaluated.3.1.4 protec
9、tive clothing, na product which is designedand constructed for the purpose of isolating parts of the bodyfrom a potential hazard.3.1.4.1 DiscussionIn this test method, gloves are evalu-ated to determine the effect on the hand function of the wearer.3.1.5 For definitions of other protective clothing-
10、relatedterms used in this test method, refer to Terminology F 1494.4. Summary of Test Method4.1 The time required for a test subject to place pegs into apegboard is measured without gloves and then later whilewearing gloves. The additional time required to perform thetask while wearing gloves is rep
11、orted and is used to indicate theeffects of the gloves on wearer dexterity.5. Significance and Use5.1 The test method is intended to provide a quantitativemeasurement about the effect of gloves on wearer dexterity bycomparing the times required to perform a simple task with andwithout gloves.5.2 Thi
12、s test method does not discriminate all glove effectson wearer hand function or apply to all glove types andapplications. Additional evaluations or tests representative ofthe glove use application should be performed to determine theoverall impact of gloves on wearer hand function.6. Apparatus6.1 Te
13、st Apparatus, a pegboard apparatus consisting of 25stainless steel pins and a pegboard. Each stainless steel pinshall have a diameter of 9.5 mm 0.375 in. and length of 38.1mm 1.5 in. The pegboard shall be 200 6 13 mm 8.0 6 0.5in. The pegboard shall have 25 holes with each hole having a1This test met
14、hod is under the jurisdiction of ASTM Committee F23 onProtective Clothing and is the direct responsibility of Subcommittee F23.60 onHuman Factors.Current edition approved July 1, 2005. Published August 2005. Originallyapproved in 2000. Last previous edition approved in 2000 as F 2010 - 00.2For refer
15、enced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West
16、 Conshohocken, PA 19428-2959, United States.diameter of 9.9 mm 0.39 in. and a depth of 13 mm 0.5 in.The holes shall be ina5by5pattern and each hole shall havea separation of 25 mm 1 in. from adjacent holes.6.2 Stopwatch, to measure the time to place the pegs into thepegboard in seconds.6.3 Test Surf
17、ace, an area at least 600 by 900 mm 23.5 by33.5 in. with a flat, level, smooth surface having a hardness of50 6 5 Shore A.7. Test Specimen7.1 For each style of glove evaluated, test five pairs (tengloves), preferably of five different sizes. When less than fivedifferent glove sizes are available for
18、 the particular glove style,test different pairs of the same size so that a total of at least fivedifferent glove pairs are tested.7.2 Test each glove in new, as distributed, condition. Do notapply special softening treatments to gloves prior to tests.8. Test Preparation8.1 Evaluate each pair of glo
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMF201020002005STANDARDTESTMETHODFOREVALUATIONOFGLOVEEFFECTSONWEARERHANDDEXTERITYUSINGAMODIFIEDPEGBOARDTEST

链接地址:http://www.mydoc123.com/p-536284.html