ASTM E1181-2002(2015) Standard Test Methods for Characterizing Duplex Grain Sizes《双重晶粒度表征与测定方法》.pdf

《ASTM E1181-2002(2015) Standard Test Methods for Characterizing Duplex Grain Sizes《双重晶粒度表征与测定方法》.pdf》由会员分享，可在线阅读，更多相关《ASTM E1181-2002(2015) Standard Test Methods for Characterizing Duplex Grain Sizes《双重晶粒度表征与测定方法》.pdf（15页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: E1181 02 (Reapproved 2015)Standard Test Methods forCharacterizing Duplex Grain Sizes1This standard is issued under the fixed designation E1181; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision.

2、 A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.INTRODUCTIONTest methods are well established for the determination of average grain size, and estimation oflargest grain size, in products assu

3、med to contain a single log-normal distribution of grain sizes. Thetest methods in this standard are set forth to characterize grain size in products with any otherdistributions of grain size.The term “duplex grain size” is chosen to describe any of these other distributions of grain size,because of

4、 its common usage and familiarity. However, the use of that term does not imply that onlytwo grain size distributions exist.These test methods are equally aimed at describing the nature of the deviation from a singlelog-normal distribution of grain sizes, and at describing with reasonable accuracy t

5、he distributions ofsizes that actually exist.1. Scope1.1 These test methods provide simple guidelines for decid-ing whether a duplex grain size exists. The test methodsseparate duplex grain sizes into one of two distinct classes,then into specific types within those classes, and providesystems for g

6、rain size characterization of each type.1.2 UnitsThe values stated in SI units are to be regardedas standard. No other units of measurement are included in thisstandard.1.3 This standard may involve hazardous materials,operations, and equipment. This standard does not purport toaddress all of the sa

7、fety concerns associated with its use. It isthe responsibility of the user of this standard to consultappropriate safety and health practices and determine theapplicability of regulatory limitations prior to its use.2. Referenced Documents2.1 ASTM Standards:2E3 Guide for Preparation of Metallographi

8、c SpecimensE7 Terminology Relating to MetallographyE112 Test Methods for Determining Average Grain SizeE407 Practice for Microetching Metals and AlloysE562 Test Method for Determining Volume Fraction bySystematic Manual Point CountE883 Guide for ReflectedLight PhotomicrographyE930 Test Methods for E

9、stimating the Largest Grain Ob-served in a Metallographic Section (ALA Grain Size)2.2 ASTM Adjuncts:Comparison Chart for Estimation of Area Fractions33. Terminology3.1 Definitions:3.1.1 All terms used in these test methods are either definedin Terminology E7, or are discussed in 3.2.3.2 Definitions

10、of Terms Specific to This Standard:3.2.1 bands or banding in grain size, alternating areas ofsignificantly different grain sizes. These areas are usuallyelongated in a direction parallel to the direction of working.3.2.2 grain sizeequivalent in meaning to the average of adistribution of grain sizes.

11、3.2.3 necklace or necklace structureindividual coarsegrains surrounded by rings of significantly finer grains.3.2.4 topologically varyingvarying nonrandomly, in somedefinable pattern; that pattern may be related to the shape of thespecimen or product being examined.4. Summary of Test Method4.1 These

12、 test methods provide means for recognizing thepresence of duplex grain size. The test methods separate duplex1These test methods are under the jurisdiction of ASTM Committee E04 onMetallography and are the direct responsibility of Subcommittee E04.08 on GrainSize.Current edition approved Oct. 1, 20

13、15. Published November 2015. Originallyapproved in 1987. Last previous edition approved in 2008 as E118102(2008)1.DOI: 10.1520/E1181-02R15.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume

14、 information, refer to the standards Document Summary page onthe ASTM website.3This comparison chart shows different area percentages of light grains amongdark grains. Available from ASTM Headquarters. Order Adjunct: ADJE1181.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Con

15、shohocken, PA 19428-2959. United States1grain sizes into two classes (randomly varying, and topologi-cally varying), and define specific types of duplex grain sizeswithin these classes. The test methods provide means forestimating area fractions occupied by distinct grain sizes, andoffer existing st

16、andard methods (Test Methods E112, TestMethods E930) for determining grain size in specific identifiedareas. The test methods provide for reporting of specific,distinctive information for each type of duplex grain size. And,as an alternative, the test methods offer a procedure forstatistically deter

17、mining the distribution of all the grain sizespresent in a duplex grain size specimen.5. Significance and Use5.1 Duplex grain size may occur in some metals and alloysas a result of their thermomechanical processing history. Forcomparison of mechanical properties with metallurgicalfeatures, or for sp

18、ecification purposes, it may be important tobe able to characterize grain size in such materials. Assigningan average grain size value to a duplex grain size specimendoes not adequately characterize the appearance of thatspecimen, and may even misrepresent its appearance. Forexample, averaging two d

19、istinctly different grain sizes mayresult in reporting a size that does not actually exist anywherein the specimen.5.2 These test methods may be applied to specimens orproducts containing randomly intermingled grains of two ormore significantly different sizes (henceforth referred to asrandom duplex

20、 grain size). Examples of random duplex grainsizes include: isolated coarse grains in a matrix of much finergrains, extremely wide distributions of grain sizes, and bimodaldistributions of grain size.5.3 These test methods may also be applied to specimens orproducts containing grains of two or more

21、significantly differ-ent sizes, but distributed in topologically varying patterns(henceforth referred to as topological duplex grain sizes).Examples of topological duplex grain sizes include: systematicvariation of grain size across the section of a product, necklacestructures, banded structures, an

22、d germinative grain growth inselected areas of critical strain.5.4 These test methods may be applied to specimens orproducts regardless of their state of recrystallization.5.5 Because these test methods describe deviations from asingle, log-normal distribution of grain sizes, and characterizepattern

23、s of variation in grain size, the total specimen cross-section must be evaluated.5.6 These test methods are limited to duplex grain sizes asidentifiable within a single polished and etched metallurgicalspecimen. If duplex grain size is suspected in a product toolarge to be polished and etched as a s

24、ingle specimen, mac-roetching should be considered as a first step in evaluation. Theentire macroetched cross-section should be used as a basis forestimating area fractions occupied by distinct grain sizes, ifpossible. If microscopic examination is subsequentlynecessary, individual specimens must be

25、 taken to allow esti-mation of area fractions for the entire product cross-section,and to allow determination of grain sizes representing theentire cross-section as well.5.7 These test methods are intended to be applied to duplexgrain sizes. Duplex grain structures (for example, multiphasealloys) ar

26、e not necessarily duplex in grain size, and as such arenot the subject of these methods. However, the test methodsdescribed here for area fraction estimation may be of use indescribing duplex grain structures.6. Apparatus6.1 Certain items may be helpful or necessary in applyingthe various procedures

27、 of these test methods. These items arebriefly described below, under the headings of the specificprocedures to which they apply.6.1.1 Comparison Procedure for Estimation of AreaFractionsThis procedure requires the use of a comparisonchart to improve the accuracy of visual estimates of areaFIG. 1 Co

28、mparison Chart for Estimation of Area Fractions1(Showing area percentages of light grains among dark grains)E1181 02 (2015)2fractions occupied by distinct grain sizes. This comparisonchart is shown in Fig. 14. The chart shows different areapercentages of light grains among dark grains.6.1.2 Point Co

29、unt Procedure for Estimation of AreaFractionsThis procedure requires the use of a test grid on atransparent overlay, or in a reticle, that can be superimposed onthe specimen image. The grid should consist of equally spacedpoints formed by the intersection of fine lines. Practice E562gives examples o

30、f such grids, as well as details on recom-mended grid spacing, and use of the grid.6.1.3 Planimetric Procedure for Estimation of AreaFractionsThis procedure requires the use of a planimeter, adevice for measuring the areas of irregular polygons. Theregions occupied by a distinct grain size are manua

31、lly outlinedon a photomicrograph or transparent overlay. The area of eachof those regions is then measured by tracing its outline with theplanimeter.56.1.4 Test Methods E930, Comparison Procedure for Esti-mation of Largest Grain Size Observed.6.1.4.1 This procedure requires the use of a visual aid f

32、orestimation of the size of the largest grain found in a givenmetallographic section. That visual aid is shown in TestMethods E930, and is available as an ASTM Adjunct (see TestMethods E930 for details).6.1.5 Test Methods E930, Measuring Procedure for Estima-tion of Largest Grain Size Observed.6.1.5

33、.1 This procedure may require the use of a measuringmicroscope eyepiece or measuring microscope reticle. Theseare available from microscope manufacturers.6.1.6 Test Methods E930, Referee Procedure for Estimationof Largest Grain Size Observed.6.1.6.1 This procedure requires the use of a test grid on

34、atransparent overlay that can be superimposed on the specimenimage. The test grid consists of a square network of grid lines,with a recommended interline spacing of 5 mm. Use of the gridis described in Test Methods E930.6.1.7 Test Methods E112, Comparison Procedure for Deter-mination of Average Grai

35、n Size.6.1.7.1 This procedure requires the use of grain size com-parison charts or overlay transparencies, or grain size compari-son reticles fitted into microscopes. Various comparison chartsand overlay transparencies are available as ASTM adjuncts(see Test Methods E112 for details).6.1.7.2 Grain s

36、ize comparison reticles are available fromvarious manufacturers of microscopes.6.1.8 Test Methods E112, Intercept Procedures for Determi-nation of Average Grain Size,6.1.8.1 The Intercept Procedures of Test Methods E112require the use of patterns of test lines, usually on transparentoverlays. The us

37、e of these is described in detail in TestMethods E112. A transparency of one such pattern is availableas an ASTM adjunct (see Test Methods E112 for details).6.1.9 Statistical Determination of Grain Size Distribution:6.1.9.1 This procedure requires the use of a test grid on atransparent overlay that

38、can be superimposed on the specimenimage. The test grid consists of a series of fine, parallel lines,with an interline spacing of 5 mm. Use of the grid is describedin 8.7.6.1.9.2 This procedure may be carried out using manualmeasuring and counting techniques, but as such, will be verylaborious and t

39、ime-consuming. This procedure can be carriedout much more efficiently through the use of an automatedimage analysis system with an electronic pencil or cursor, orthrough the use of a semi-automated image analysis systemwith a digitizing tablet and electronic pencil or cursor.6The useof this equipmen

40、t is also described in 8.7.7. Sampling and Test Specimens7.1 Sampling:7.1.1 These test methods are intended to characterize pat-terns of variation in grain size, when they occur in a givenspecimen or product. To characterize these patterns accurately,the entire cross-section of the specimen or produ

41、ct must beevaluated.7.1.2 If variations in grain size occur in a product too largeto be polished and etched as a single specimen, individualspecimens must be taken to allow estimation of area fractionsfor the entire product cross-section, and to allow determinationof grain sizes representing the ent

42、ire cross-section as well.7.2 Specimen Orientation:7.2.1 All of the types of duplex grain size described in thistest method (see 3.2 and 8.3) can be detected in a longitudinalspecimen orientation (that is, in a plane parallel to the directionof maximum product deformation, during manufacture).Accord

43、ingly, the longitudinal orientation is recommended,with one exception. If the specimen being examined is the fullcross-section of a round bar, the longitudinal section should notbe used to estimate the area fraction occupied by different grainsizes. That estimate can be made most accurately only on

44、atransverse section. For a tubular product, estimates of areafractions made on longitudinal sections are reasonable approxi-mations of the same estimates made on transverse sections. Forall other products, area fraction estimates should be equallyaccurate with either specimen orientation.7.2.2 Other

45、 specimen orientations may be used, providedthat their limitations are recognized. For instance, bandingpresent in a given specimen may not be easily recognizable ina transverse orientation.7.2.3 The specimen orientation used should be reportedalong with the duplex grain size characterization.8. Pro

46、cedure8.1 Specimen PreparationPrepare specimens according toMethods E3, and etch specimens in accordance with PracticeE407. Etch specimens so that all grain boundaries are distinctand easily visible.4Leidheiser, H., Jr and Kim, D. K., “A Chemical Test for Identifying theFraction of Grains in the Sur

47、face of Galvanized Steel Sheet That Have OrientationsApproximating (0001)Importance to Paint Adherence,”Metallurgical Transac-tions “B,” American Society for Metals, Metals Park, OH 44073, December, 1978,p. 590.5A Keuffel or, the presence of different grain sizes inspecific areas of a product cross-

48、section (for example, coarsegrains resulting from germinative grain growth at areas ofcritical strain), such that the grain size in those specific areasdiffers from the grain size in the bulk of the cross-section bythree or more ASTM grain size numbers (both conditionshenceforth referred to as the c

49、ross-section condition). Anexample photomicrograph of a cross-section condition appearsin Fig. A1.4.8.3.2.2 The presence of individual coarse grains, eachsurrounded by rings of finer grains, the coarse and fine grainsdiffering in size by three or more ASTM grain size numbers(henceforth referred to as the necklace condition). An examplephotomicrograph of the necklace condition appears in Fig.A1.5.8.3.2.3 The presence of bands of distinct grain sizes, suchthat the sizes differ by three or moreASTM grain size numbers(henceforth referred to as the banding condition). An examp