ASTM D6744-2006(2011)e1 0625 Standard Test Method for Determination of the Thermal Conductivity of Anode Carbons by the Guarded Heat Flow Meter Technique《采防护热流量计技术测定阳极炭热导率的标准试验方法》.pdf

《ASTM D6744-2006(2011)e1 0625 Standard Test Method for Determination of the Thermal Conductivity of Anode Carbons by the Guarded Heat Flow Meter Technique《采防护热流量计技术测定阳极炭热导率的标准试验方法》.pdf》由会员分享，可在线阅读，更多相关《ASTM D6744-2006(2011)e1 0625 Standard Test Method for Determination of the Thermal Conductivity of Anode Carbons by the Guarded Heat Flow Meter Technique《采防护热流量计技术测定阳极炭热导率的标准试验方法》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D6744 06 (Reapproved 2011)1Standard Test Method forDetermination of the Thermal Conductivity of AnodeCarbons by the Guarded Heat Flow Meter Technique1This standard is issued under the fixed designation D6744; the number immediately following the designation indicates the year oforiginal

2、 adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1NOTEUpdate wording in Notes 14, 6.3.2, 12.1.8, and updated notation in Section

3、 13 editorially in August 2011.1. Scope1.1 This test method covers a steady-state technique for thedetermination of the thermal conductivity of carbon materialsin thicknesses of less than 25 mm. The test method is useful forhomogeneous materials having a thermal conductivity in theapproximate range

4、1 l 30 W/(mK), (thermal resistance inthe range from 10 to 400 3 104m2K/W) over the approxi-mate temperature range from 150 to 600 K. It can be usedoutside these ranges with reduced accuracy for thicker speci-mens and for thermal conductivity values up to 60 W/(mK).NOTE 1It is not recommended to test

5、 graphite cathode materials usingthis test method. Graphites usually have a very low thermal resistance, andthe interfaces between the specimen to be tested and the instrumentbecome more significant than the specimen itself.1.2 This test method is similar in concept to Test MethodsE1530 and C518. Si

6、gnificant attention has been paid to ensurethat the thermal resistance of contacting surfaces is minimizedand reproducible.1.3 The values stated in SI units are regarded as standard.The values given in parentheses are for information only.1.4 This standard does not purport to address all of thesafet

7、y concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2C518 Test Method for Steady-State

8、 Thermal TransmissionProperties by Means of the Heat Flow Meter ApparatusE1530 Test Method for Evaluating the Resistance to Ther-mal Transmission of Materials by the Guarded Heat FlowMeter Technique3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 average temperature, nthe avera

9、ge temperature of asurface is the area-weighted mean temperature of that surface.3.1.2 heat flux transducer, HFT, na device that producesan electrical output that is a function of the heat flux, in apredefined and reproducible manner.3.1.3 thermal conductance, C, nthe time rate of heat fluxthrough a

10、 unit area of a body induced by unit temperaturedifference between the body surfaces.3.1.4 thermal conductivity, l, of a solid material, nthetime rate of heat flow, under steady conditions, through unitarea, per unit temperature gradient in the direction perpendicu-lar to the area.3.1.5 thermal resi

11、stance, R, nthe reciprocal of thermalconductance.3.2 Symbols:l = thermal conductivity, W/(mK), Btuin/(hft2F)C = thermal conductance, W/(m2K), Btu/(hft2F)R = thermal resistance, m2K/W, hft2F/BtuDx = specimen thickness, mm, inA = specimen cross sectional area, m2,ft2Q = heat flow, W, Btu/hf = heat flu

12、x transducer output, mVN = heat flux transducer calibration constant,W/(m2mV), Btu/(hft2mV)Nf = heat flux, W/m2, Btu/(hft2)DT = temperature difference, C, FTg= temperature of guard heater, C, FTu= temperature of upper heater, C, FTl= temperature of lower heater, C, FT1= temperature of one surface of

13、 the specimen, C, FT2= temperature of the other surface of the specimen, C,FTm= mean temperature of the specimen, C, Fs = unknown specimen1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products and Lubricants and is the direct responsibility of SubcommitteeD02.05 on Pr

14、operties of Fuels, Petroleum Coke and Carbon Material.Current edition approved May 1, 2011. Published August 2011. Originallyapproved in 2001. Last previous edition in 2006 as D674406. DOI: 10.1520/D6744-06R11.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Custo

15、mer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.r = known calibration or reference s

16、pecimeno = contacts4. Summary of Test Method4.1 A specimen and a heat flux transducer (HFT) aresandwiched between two flat plates controlled at differenttemperatures, to produce a heat flow through the test stack. Areproducible load is applied to the test stack by pneumatic orhydraulic means, to ens

17、ure that there is a reproducible contactresistance between the specimen and plate surfaces. A cylin-drical guard surrounds the test stack and is maintained at auniform mean temperature of the two plates, in order tominimize lateral heat flow to and from the stack. At steady-state, the difference in

18、temperature between the surfacescontacting the specimen is measured with temperature sensorsembedded in the surfaces, together with the electrical output ofthe HFT. This output (voltage) is proportional to the heat flowthrough the specimen, the HFT and the interfaces between thespecimen and the appa

19、ratus. The proportionality is obtainedthrough prior calibration of the system with specimens ofknown thermal resistance measured under the same conditions,such that contact resistance at the surface is made reproducible.5. Significance and Use5.1 This test method is designed to measure and compareth

20、ermal properties of materials under controlled conditions andtheir ability to maintain required thermal conductance levels.6. Apparatus6.1 Aschematic rendering of a typical apparatus is shown inFig. 1. The relative position of the HFT to sample is notimportant (it may be on the hot or cold side) as

21、the test methodis based on maintaining axial heat flow with minimal heatlosses or gains radially. It is also up to the designer whether tochoose heat flow upward or downward or horizontally, al-though downward heat flow in a vertical stack is the mostcommon one.6.2 Key Components of a Typical Device

22、:6.2.1 The compressive force for the stack is to be providedby either a regulated pneumatic or hydraulic cylinder (1) or aspring loaded mechanism. In either case, means must beprovided to ensure that the loading can be varied and set tocertain values reproducibility.6.2.2 The loading force must be t

23、ransmitted to the stackthrough a gimball joint (2) that allows up to 5 swivel in theplane perpendicular to the axis of the stack.6.2.3 Suitable insulator plate (3) separates the gimball jointfrom the top plate (4).6.2.4 The top plate (assumed to be the hot plate for thepurposes of this description)

24、is equipped with a heater (5) andcontrol thermocouple (6) adjacent to the heater, to maintain acertain desired temperature. (Other means of producing andmaintaining temperature may also be used as long as therequirements under 6.3 are met.) The construction of the topplate is such as to ensure unifo

25、rm heat distribution across itsface contacting the sample (8). Attached to this face (orembedded in close proximity to it), in a fashion that does notinterfere with the sample/plate interface, is a temperaturesensor (7) (typically a thermocouple, thermistor) that definesthe temperature of the interf

26、ace on the plate side.6.2.5 The sample (8) is in direct contact with the top plateon one side and an intermediate plate (9) on the other side.6.2.6 The intermediate plate (9) is an optional item. Itspurpose is to provide a highly conductive environment to theFIG. 1 Key Components of a Typical Device

27、D6744 06 (2011)12second temperature sensor (10), to obtain an average tempera-ture of the surface. If the temperature sensor (10) is embeddedinto the face of the HFT, or other means are provided to definethe temperature of the surface facing the sample, the use of theintermediate plate is not mandat

28、ory.6.2.7 Heat flux transducer (HFT) is a device that willgenerate an electrical signal in proportion to the heat fluxacross it. The level of output required (sensitivity) greatlydepends on the rest of the instrumentation used to read it. Theoverall performance of the HFTand its readout instrumentat

29、ionshall be such as to meet the requirements in Section 13.6.2.8 The lower plate (12) is constructed similarly to theupper plate (4), except it is positioned as a mirror image.6.2.9 An insulator plate (16) separates the lower plate (12)from the heat sink (17). In case of using circulating fluid inpl

30、ace of a heater/thermocouple arrangement in the upper and/orlower plates, the heat sink may or may not be present.6.2.10 The entire stack is surrounded by a cylindrical guard(18) equipped with a heater (19) and a control thermocouple(20) to maintain it at the mean temperature between the upperand lo

31、wer plates. A small, generally unfilled gap separates theguard from the stack. For instruments limited to operate in theambient region, no guard is required. A draft shield is recom-mended in place of it.NOTE 2It is permissible to use thin layers of high conductivity greaseor elastomeric material on

32、 the two surfaces of the specimen to reduce thethermal resistance of the interface and promote uniform thermal contactacross the interface area.NOTE 3The cross sectional area of the specimen may be any,however, most commonly circular and rectangular cross sections are used.Minimum size is dictated b

33、y the magnitude of the disturbance caused bythermal sensors in relation to the overall flux distribution. The mostcommon sizes are 25 mm round or square to 50 mm round.6.3 Requirements:6.3.1 Temperature control of upper and lower plate is to be6 0.1 C (6 0.18 F) or better.6.3.2 Reproducible load of

34、0.28 MPa (40 psi) has beenfound to be satisfactory for solid specimens. Minimum loadshall not be below 0.07 MPa (10 psi).6.3.3 Temperature sensors are usually fine gage or smalldiameter sheath thermocouples, however, ultraminiature resis-tance thermometers and linear thermistors may also be used.6.3

35、.4 Operating range of a device using a mean temperatureguard shall be limited to 100 C to 300 C, when usingthermocouples as temperature sensors, and 180 C to 300 Cwith platinum resistance thermometers.7. Test Specimen7.1 The specimen to be tested shall be representative for thesample material. The r

36、ecommended specimen configuration isa 50.8 6 0.25 mm (2 6 0.010 in.) diameter disk, havingsmooth flat and parallel faces, 6 0.025 mm (6 0.001 in.), suchthat a uniform thickness within 0.025 mm (6 0.001 in.) isattained in the range from 12.7 to 25.4 mm (0.5 to 1.0 in.)8. Sampling and Conditioning8.1

37、Cut representative test specimens from larger pieces ofthe sample material or body.8.2 Condition the cut specimens in accordance with therequirements of the appropriate material specifications, if any.9. Calibration9.1 Select the mean temperature and load conditions re-quired. Adjust the upper heate

38、r temperature (Tu) and lowerheater temperature (Tl) such that the temperature difference atthe required mean temperature is no less than 30 to 35 C andthe specimen DT is not less than 3 C. Adjust the guard heatertemperature (Tg) such that it is at approximately the average ofTuand Tl.9.2 Select at l

39、east two calibration specimens having thermalresistance values that bracket the range expected for the testspecimens at the temperature conditions required.9.3 Table 1 contains a list of several available materialscommonly used for calibration, together with correspondingthermal resistance (Rs) valu

40、es for a given thickness. Thisinformation is provided to assist the user in selecting optimumspecimen thickness for testing a material and in deciding whichcalibration specimens to use.9.4 The range of thermal conductivity for which this testmethod is most suitable is such that the optimum thermalre

41、sistance range is from 10 3 104to 400 3 104m2K/W.The most commonly used calibration materials are the Pyrex7740, Pyroceram 9606, and stainless steel.9.5 Measure the thickness of the specimen to 25 m.9.6 Coat both surfaces of a calibration specimen with a verythin layer of a compatible heat sink comp

42、ound or place a thinlayer of elastomeric heat transfer medium on it to helpminimize the thermal resistance at the interfaces of adjacentcontacting surfaces.9.7 Insert the calibration specimen into the test chamber.Exercise care to ensure that all surfaces are free of any foreignmatter.9.8 Close the

43、test chamber and clamp the calibration speci-men in position between the plates at the recommendedcompressive load of 0.28 MPa.9.9 Wait for thermal equilibrium to be attained. This shouldbe seen when all the temperatures measured do not drift morethan 0.1 C in 1 min. Read and record all temperatures

44、 and theoutput of the heat flux transducer.NOTE 4The time to attain thermal equilibrium is dependent upon theTABLE 1 Typical Thermal Resistance Values of Specimens ofDifferent MaterialsMaterial ApproximateThermalConductivity,W/(mK) at30CThickness,mmApproximateThermalResistance,104m2K/W at30 CPyrocer

45、am 9606A42050Pyroceram 9606A41 2Pyrex 7740AGlass 1 20 200Pyrex 7740AGlass 1 10 100Pyrex 7740AGlass 1 1 10304 Stainless Steel 14 20 14304 Stainless Steel 14 10 7VespelB0.4 2 50APyrex 7740 and Pyroceram 9606 are products and trademarks of CorningGlass Co., Corning, WV.BVespel is a product of DuPont Co

46、.D6744 06 (2011)13thickness of the specimen and its thermal properties. Experience showsthat approximately1hisneeded for thermal equilibrium to be attained,when testing a specimen with the thermal conductivity within theoptimum operating range of the instrument.9.10 Repeat the procedure in 9.5 to 9.

47、9 with one or morecalibration specimens, having different thermal resistance val-ues covering the expected range for the test specimen.10. Thermal Conductivity of an Unknown Specimen10.1 Tests shall only be conducted at a temperature in arange and under applied load conditions for which validcalibra

48、tion data exists.10.1.1 When automatic control of temperature of the heatersis involved, the controller settings should be checked to ensurethat they are the same as those for the desired temperature levelfor the calibration.10.2 Measure the thickness of the specimen to 25 m.10.3 Apply a thin layer

49、of heat sink compound or place athin layer of elastomeric heat transfer medium on the surfacesof the test specimen.NOTE 5Exercise care to ensure that any material applied to thesurfaces of the specimen does not change its thermal properties by soakinginto it.10.4 Repeat the procedure in 9.7 to 9.9 using the testspecimen.NOTE 6Experience has indicated that for reliable measurements on asingle specimen, the minimum thickness (mm) is given by Dx $ 3l(W/(mK).10.5 Automated SystemsComputerized or otherwise a