ASTM C752-2003 Standard Specification for Nuclear-Grade Silver-Indium-Cadmium Alloy《核纯级的银铟镉合金标准规范》.pdf

《ASTM C752-2003 Standard Specification for Nuclear-Grade Silver-Indium-Cadmium Alloy《核纯级的银铟镉合金标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM C752-2003 Standard Specification for Nuclear-Grade Silver-Indium-Cadmium Alloy《核纯级的银铟镉合金标准规范》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: C 752 03Standard Specification forNuclear-Grade Silver-Indium-Cadmium Alloy1This standard is issued under the fixed designation C 752; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number

2、 in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers silver-indium-cadmium alloyfor use as a control material in light-water nuclear reactors.1.2 The scope of this spe

3、cification excludes the use of thismaterial in applications where material strength of this alloy isa prime requisite. Also, this material must be protected fromthe primary water by a corrosion and wear resistant cladding.2. Referenced Documents2.1 ASTM Standards:C 760 Test Methods for Chemical and

4、SpectrochemicalAnalysis of Nuclear-Grade Silver-Indium-Cadmium Al-loys2C 859 Terminology Relating to Nuclear Materials2E 105 Practice for Probability Sampling of Materials32.2 ANSI Standard:B46.1 Surface Roughness4ANSI/ASME NQA-1 Quality Assurance Program Require-ments for Nuclear Facility Applicati

5、ons42.3 U.S. Government Standard:Title 10 Code of Federal Regulations, Energy Part 50(10CFR50) Domestic Licensing of Production and Utili-zation Facilities53. Terminology3.1 Terms shall be defined in accordance with the terminol-ogy in Terminology C 859, except for the following:3.1.1 The term “buye

6、r” shall refer to the organizationissuing the purchase order.3.1.2 The term “seller” shall refer to the silver-indium-cadmium supplier.3.1.3 A lot shall be defined as all parts produced from thesame melt by the same process.4. Ordering Information4.1 The buyer shall specify the following information

7、 on theorder:4.1.1 Quantity,4.1.2 Lot size, and4.1.3 Dimensions and tolerances.5. Materials and Manufacture5.1 The identity of each lot by melt number shall bemaintained at all stages of manufacture.5.2 Parts produced to this specification shall be made frombillets by hot working and cold finishing

8、to size.5.3 The cold-finished parts shall be produced to the finishcondition and dimensions as specified in the purchase order.6. Chemical Composition6.1 The parts shall conform to the following chemicalcomposition:Element Weight %Indium 15.00 6 0.25Cadmium 5.00 6 0.25Total impurities, max 0.50 maxS

9、ilver remainderLead 0.03 maxBismuth 0.03 max7. Workmanship, Finish, and Appearance7.1 The surface of the cold-finished part shall be free ofoxides, grease, oil, residual lubricants, inclusions, and otherextraneous materials.7.2 Surface defects such as folds, cracks, seams, slivers, andblisters shall

10、 be cause for rejection.7.3 Surface roughness shall be per B46.1 not to exceed 0.81m rms (32 in. rms).8. Sampling8.1 A sampling plan to meet the acceptance criteria shall beagreed to between the buyer and the seller. Samples forchemical analysis shall be taken after completion of allhot-working oper

11、ations. Recommended Practice E 105 is ref-erenced as a guide.8.2 The sample shall be sufficient to perform quality controltests, acceptance tests and referee tests, as necessary.8.2.1 Quality control tests,1This specification is under the jurisdiction of ASTM Committee C26 onNuclear Fuel Cycle and i

12、s the direct responsibility of Subcommittee C26.03 onNeutron Absorber Materials Specifications.Current edition approved July 10, 2003. Published August 2003. Originallyapproved in 1973. Last previous edition approved in 1997 as C 752 88(1997).2Annual Book of ASTM Standards, Vol 12.01.3Annual Book of

13、 ASTM Standards, Vol 14.02.4Available from American National Standards Institute, 11 W. 42nd St., 13thFloor, New York, NY 10036.5Available from U.S. Government Printing Office, North Capital and H StreetsNW, Washington, DC 20401.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West

14、 Conshohocken, PA 19428-2959, United States.8.2.2 Acceptance tests, and8.2.3 Referee tests.9. Methods of Chemical Analysis9.1 Use analytical chemistry methods in accordance withTest Method C 760 or demonstrated equivalent methods agreedupon between the buyer and the seller.10. Inspection and Certifi

15、cation10.1 Each part shall be visually inspected for cleanlinessand the absence of defects.10.2 Each part shall be inspected for dimensions as speci-fied in the purchase order.10.3 The seller shall furnish the buyer with certificates oftests showing the results of testing and inspection performed on

16、each lot prior to shipment.11. Rejection and Rehearing11.1 Rejection of a lot or a part for failure to meet thisspecification shall be reported by the buyer to the seller within60 calendar days. Rejected material may be returned to theseller at the sellers expense, unless the buyer receives, within3

17、 weeks of notice of rejection, other instructions for disposi-tion.12. Packaging and Package Marking12.1 Each part shall be individually wrapped or bagged andpacked in suitable containers to prevent damage and contami-nation during shipment and storage.12.2 The seller will be responsible for designi

18、ng the ship-ping container to assure cleanliness, to provide adequateprotection against damage during transportation, and to assurereasonable ease of unpackaging.12.3 Each container shall contain material from only one lotand shall be clearly marked with the following: purchase ordernumber, purchase

19、 order specifications, gross, net, and tareweights, lot number, and manufacturers alloy designation.13. Quality Assurance13.1 Quality assurance requirements shall be agreed uponbetween the buyer and the seller when specified in the purchaseorder. Code of Federal Regulations, Title 10 Part 50 Appendi

20、xB and NQA-1 are referenced as guides.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the r

21、iskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of t

22、his standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmak

23、e your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).C752032