ASTM C1319-2001(2006) Standard Specification for Concrete Grid Paving Units《混凝土格子铺设装置的标准规范》.pdf

《ASTM C1319-2001(2006) Standard Specification for Concrete Grid Paving Units《混凝土格子铺设装置的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM C1319-2001(2006) Standard Specification for Concrete Grid Paving Units《混凝土格子铺设装置的标准规范》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: C 1319 01 (Reapproved 2006)Standard Specification forConcrete Grid Paving Units1This standard is issued under the fixed designation C 1319; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A n

2、umber in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers the requirements for concretegrid paving units for vehicular trafficways, parking areas, soilstabilization,

3、and revetments. Maximum dimensions are 24long by 24 in. wide (610 by 610 mm), with a minimumnominal thickness of 318 in. (80 mm).NOTE 1When particular features are desired, such as weight classifi-cation, higher compressive strength, surface texture, finish, color, or otherspecial features, such pro

4、perties should be specified separately by thepurchaser. However, local sellers should be consulted as to availability ofunits having the desired features.1.2 The text of this standard references notes and footnoteswhich provide explanatory material. These notes and footnotes(excluding those in table

5、s and figures) shall not be consideredas requirements of the standard.1.3 The values stated in inch-pound units are to be regardedas the standard. The values given in parentheses are forinformation only.2. Referenced Documents2.1 ASTM Standards:2C33 Specification for Concrete AggregatesC 140 Test Me

6、thods for Sampling and Testing ConcreteMasonry Units and Related UnitsC 150 Specification for Portland CementC 331 Specification for Lightweight Aggregates for Con-crete Masonry UnitsC 595 Specification for Blended Hydraulic CementsC 618 Specification for Coal Fly Ash and Raw or CalcinedNatural Pozz

7、olan for Use in ConcreteC 989 Specification for Ground Granulated Blast-FurnaceSlag for Use in Concrete and MortarsC 1157 Performance Specification for Hydraulic CementC 1209 Terminology of Concrete Masonry Units and Re-lated UnitsC 1232 Terminology of Masonry3. Terminology3.1 Terminology defined in

8、 Terminology C 1209 and Ter-minology C 1232 shall apply for this specification.4. Materials4.1 Cementitious MaterialsMaterials shall conform to thefollowing applicable ASTM specifications:4.1.1 Portland CementsSpecification C 150.4.1.2 Modified Portland CementPortland cement con-forming to Specifica

9、tion C 150, modified as follows:4.1.2.1 Calcium carbonate, with a minimum 85 % CaCO3content, shall be permitted to be interground with the cement,provided the requirements of Specification C 150 as modifiedare met: limitation on insoluble residue is 1.5 % and limitationon loss on ignition is 7 %.4.1

10、.3 Blended Hydraulic CementsSpecification C 595.4.1.4 Hydraulic CementSpecification C 1157.4.1.5 PozzolansSpecification C 618.4.1.6 Blast Furnace Slag CementsSpecification C 989.4.2 AggregatesAggregates shall conform to one of thefollowing ASTM specifications, except that grading require-ments shall

11、 not necessarily apply:4.2.1 Normal WeightSpecification C33.4.2.2 LightweightSpecification C 331.4.3 Other ConstituentsAir-entraining agents, coloringpigments, integral water repellents, and finely ground silica,shall be previously established as suitable for use in concretegrid paving units and sha

12、ll conform to applicable ASTMstandards, or they shall be shown by test or experiencesatisfactory to the specifier and not to be detrimental to thedurability of the concrete grid paving unit or any materialcustomarily used in grid paving construction.5. Physical Requirements5.1 At the time of deliver

13、y to the work site, the units shallconform to the physical requirements prescribed in Table 1.5.2 DurabilityDurability shall be demonstrated by provenfield performance satisfactory to the specifier that the gridpaver units have adequate durability for the intended use.1This specification is under th

14、e jurisdiction of ASTM Committee C15 onManufactured Masonry Units and is the direct responsibility of SubcommitteeC15.03 on Concrete Masonry Units and Related Units.Current edition approved Dec. 1, 2006. Published December 2006. Originallyapproved in 1995. Last previous edition approved in 2001 as C

15、 1319 01.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1*A Summary of Changes section appears at the end of

16、 this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5.2.1 Proven Field PerformanceSatisfactory field perfor-mance is demonstrated when units similar in composition andmade with the same manufacturing process as those to bes

17、upplied to the purchaser, maintain the physical requirementsspecified in Table 1 after three years of use. The units used asthe basis for proven field performance shall have been exposedto the same general type of environment, temperature range,and traffic volume as is expected for the units supplie

18、d to thepurchaser.6. Permissible Variations in Dimensions6.1 Length or width of units shall not differ by more than618 in. (63.2 mm) from approved samples. Heights of unitsshall not differ by more than 618 in. (63.2 mm) from thespecified standard dimensions. Tests shall be performed asrequired in 7.

19、2.7. Sampling and Testing7.1 The purchaser or his authorized representative shall beaccorded proper facilities to inspect and sample the units at theplace of manufacture from lots ready for delivery.7.2 Sample and test units in accordance with Test MethodsC 140, except that the coupon method for det

20、ermining com-pressive strength shall not be used.8. Visual Inspection8.1 Units shall be free of defects that interfere with theproper placing of the unit or impair the strength or permanenceof the construction.9. Compliance9.1 If a sample fails to conform to the specified require-ments, the manufact

21、urer shall be permitted to remove unitsfrom the shipment. A new sample shall be selected by thepurchaser from remaining units from the shipment with asimilar configuration and dimension and tested at the expenseof the manufacturer. If the second sample meets the specifiedrequirements, the remaining

22、portion of the shipment repre-sented by the sample meets the specified requirements. If thesecond sample fails to meet the specified requirements, theremaining portion of the shipment represented by the samplefails to meet the specified requirements.NOTE 2Unless otherwise specified in the purchase o

23、rder, the costs oftests is typically borne as follows: (1) if the results of the tests show thatthe units do not conform to the requirements of this specification the costis typically borne by the seller; ( 2) if the results of the tests show that theunits conform to the specification requirements,

24、the cost is typically borneby the purchaser.10. Keywords10.1 concrete grid paving units; revetments; soil stabiliza-tion; vehicular trafficwaysSUMMARY OF CHANGESCommittee C15 has identified the location of selected changes to this standard since C 131999 was publishedin the 2001 Annual Book of ASTM

25、Standards, Vol 04.05.(1) In Section 4 on Materials, Specification C 1157 was movedfrom Paragraph 4.1.3 to its own paragraph and identified ashydraulic cement rather than blended cement.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any i

26、tem mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical co

27、mmittee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a

28、 meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Dri

29、ve, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.o

30、rg).TABLE 1 Physical RequirementsCompressive Strength NetArea, min. psi (MPa)WaterAbsorption,max lb/ft3(kg/m3)NetArea,min.,%Web Widthin. (mm) in. (mm)Avg. of 3 Individual Avg. of 3 units Min.AAvg.B5000 (35) 4500 (31) 10 (160) 50 1.00 (25) 1.25 (32)AMeasured at the thinnest point.BAverage of measurements along the height of the web.C 1319 01 (2006)2