ASTM B621-2002(2006) Standard Specification for Nickel-Iron-Chromium-Molybdenum Alloy (UNS N08320) Rod《镍铁铬钼合金棒材标准规范》.pdf

《ASTM B621-2002(2006) Standard Specification for Nickel-Iron-Chromium-Molybdenum Alloy (UNS N08320) Rod《镍铁铬钼合金棒材标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM B621-2002(2006) Standard Specification for Nickel-Iron-Chromium-Molybdenum Alloy (UNS N08320) Rod《镍铁铬钼合金棒材标准规范》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: B 621 02 (Reapproved 2006)Standard Specification forNickel-Iron-Chromium-Molybdenum Alloy (UNS N08320)Rod1This standard is issued under the fixed designation B 621; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the y

2、ear of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification2covers nickel-iron chromium-molybdenum alloy (UNS N08320)*rod for use in generalcorrosive s

3、ervice.1.2 The following products are covered under this specifi-cation:1.2.1 Rods516 to34 in. (7.94 to 19.05 mm) excl in diameter,hot or cold finished, solution annealed and pickled or mechani-cally descaled.1.2.2 Rods34 to 312 in. (19.05 to 88.9 mm) incl in diameter,hot or cold finished, solution

4、annealed, ground or turned.1.3 The values stated in inch-pound units are to be regardedas the standard. The values given in parentheses are forinformation only.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the use

5、r of this standard to become familiarwith all hazards including those identified in the appropriateMaterial Safety Data Sheet (MSDS) for this product/materialas provided by the manufacturer, to establish appropriatesafety and health practices, and determine the applicability ofregulatory limitations

6、 prior to use.2. Referenced Documents2.1 ASTM Standards:3B 880 Specification for General Requirements for ChemicalCheck Analysis Limits for Nickel, Nickel Alloys andCobalt AlloysE8 Test Methods for Tension Testing of Metallic MaterialsE29 Practice for Using Significant Digits in Test Data toDetermin

7、e Conformance with SpecificationsE 527 Practice for Numbering Metals and Alloys (UNS)E 1473 Test Methods for Chemical Analysis of Nickel,Cobalt, and High-Temperature Alloys3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 rod, na product of round solid section furnished instraig

8、ht lengths.4. Ordering Information4.1 It is the responsibility of the purchaser to specify allrequirements that are necessary for material ordered under thisspecification. Examples of such requirements include but arenot limited to the following:4.1.1 DimensionsNominal diameter and length. Theshorte

9、st useable multiple length shall be specified (Table 1).4.1.2 CertificationState if certification or a report of testresults is required (Section 15).4.1.3 Purchaser InspectionState which tests or inspec-tions are to be witnessed (Section 13).4.1.4 Samples for Product (Check) AnalysisStatewhether sa

10、mples shall be furnished (9.2.2).5. Chemical Composition5.1 The material shall conform to the composition limitsspecified in Table 2.5.2 If a product (check) analysis is made by the purchaser,the material shall conform to the requirements specified inTable 2 subject to the permissible tolerances in

11、SpecificationB 880.6. Mechanical Properties and Other Requirements6.1 The mechanical properties of the material at roomtemperature shall conform to those shown in Table 3.7. Dimensions, Mass and Permissible Variations7.1 DiameterThe permissible variations from the speci-fied diameter shall be as pre

12、scribed in Table 4.7.2 Out of RoundnessThe permissible variation in round-ness shall be as prescribed in Table 4.1This specification is under the jurisdiction of ASTM Committee B02 onNonferrous Metals and Alloys and is the direct responsibility of SubcommitteeB02.07 on Refined Nickel and Cobalt and

13、Their Alloys.Current edition approved Dec. 1, 2006. Published December 2006. Originallyapproved in 1977. Last previous edition approved in 2002 as B 621 02.2For ASME Boiler and Pressure Vessel Code applications see related Specifi-cation SB-621 in Section II of that Code.* New designation establishe

14、d in accordance with ASTM E 527 and SAE J1086,Recommended Practice for Numbering Metals and Alloys (UNS).3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standar

15、ds Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.7.3 Matching AllowancesWhen the surfaces of finishedmaterial are to be machined, the following allowances aresuggested for normal machining o

16、perations:7.3.1 As-finished (Annealed and Descaled)For diametersof516 to1116 in. (7.94 to 17.46 mm) incl, an allowance of116in. (1.59 mm) on the diameter should be made for finishmachining.7.4 Length:7.4.1 Unless multiple, nominal, or cut lengths are specified,random mill lengths shall be furnished.

17、7.4.2 The permissible variations in length of multiple,nominal, or cut length rod shall be as prescribed in Table 1.Where rods are ordered in multiple lengths, an additional14 in.(6.35 mm) in length shall be allowed for each uncut multiplelength.7.5 Ends:7.5.1 Rods ordered to random or nominal lengt

18、hs shall befurnished with either cropped or sawed ends.7.5.2 Rods ordered to cut lengths shall be furnished withsquare saw cut or machined ends.7.6 WeightThe material covered by this specification shallbe assumed to weigh 0.291 lb/in.3(8.05 g/cm3).7.7 StraightnessThe maximum curvature (depth of cord

19、)shall not exceed 0.050 in. multiplied by the length of the cordin feet (0.04 mm multiplied by the length in centimetres).8. Workmanship, Finish, and Appearance8.1 The material shall be uniform in quality and condition,smooth, and free of injurious imperfections.9. Sampling9.1 Lots for Chemical Anal

20、ysis and Mechanical Testing:9.1.1 A lot for chemical analysis shall consist of one heat.9.1.2 A lot of bar for mechanical testing shall be defined asthe material from one heat in the same condition and specifieddiameter.9.2 Sampling for Chemical Analysis:9.2.1 A representative sample shall be obtain

21、ed from eachheat during pouring or subsequent processing.9.2.2 Product (check) analysis shall be wholly the respon-sibility of the purchaser.9.3 Sampling for Mechanical Testing:9.3.1 Arepresentative sample shall be taken from each lot offinished material.10. Number of Tests and Retests10.1 Chemical

22、AnalysisOne test per heat.10.2 Tension TestsOne test per lot.10.3 RetestsIf the specimen used in the mechanical test ofany lot fails to meet the specified requirements, two additionalspecimens shall be taken from different sample pieces andtested. The results of the tests on both of these specimens

23、shallmeet the specified requirements.11. Specimen Preparation11.1 Tension test specimens shall be taken from materialafter final heat-treatment and tested in the direction of fabri-cation.11.2 Tension test specimens shall be any of the standard orsubsized specimens shown in Test Methods E8.11.3 In t

24、he event of a disagreement, the referee specimenshall be the largest possible round specimen shown in TestMethods E8.12. Test Methods12.1 The chemical composition and mechanical propertiesof the material as enumerated in this specification shall bedetermined, in case of disagreement, in accordance w

25、ith thefollowing ASTM methods:12.1.1 Chemical AnalysisTest Methods E 1473.12.1.2 Tension TestTest Methods E8.12.1.3 Determining Significant PlacesPractice E29.12.2 For purposes of determining compliance with thelimits in this specification, an observed value or a calculatedvalue shall be rounded in

26、accordance with the rounding methodof Practice E29:TABLE 1 Permissible Variations in Length of RodsRandom mill lengths 2 to 12 ft (610 to 3660 mm) longwith not more than 25 weight % under4 ft (1.22 m).Multiple lengths Furnished in multiples of aspecified unit length, within thelength limits indicate

27、d above.For each multiple, an allowance of14 in. (6.35mm) shall be made for cutting, unlessotherwise specified. At themanufacturers option, individualspecified unit lengths may be furnished.Nominal lengths Specified nominal lengths havinga range of not less than 2 ft (610mm) with no short lengths al

28、lowed.Cut lengths A specified length to which allrods shall be cut with a permissiblevariation of +18 in. (3.17 mm) - 0.TABLE 2 Chemical RequirementsElement Composition Limits,%Nickel 25.027.0Iron remainderAChromium 21.023.0Molybdenum 4.06.0Manganese, max 2.5Carbon, max 0.05Titanium, min 4 3 carbonS

29、ilicon, max 1.00Phosphorus, max 0.04Sulfur, max 0.03ASee 12.1.1.TABLE 3 Mechanical Property RequirementsTensile Strength, min,psi (MPa)Yield Strength (0.2 %Offset), min, psi (MPa)Elongation in 2 in.(50.8) or 4DA,min,%75 000 (517) 28 000 (193) 35AD refers to the diameter of the tension specimen.B 621

30、 02 (2006)2RequirementsRounded Unit for Observed orCalculated ValueChemical composition and toler-ancenearest unit in the last right-hand placeof figures of the specified limitTensile strength and yield strength nearest 1000 psi (7 MPa)Elongation nearest 1 %13. Inspection13.1 Inspection of the mater

31、ial shall be made as agreed uponby the manufacturer and the purchaser as part of the purchasecontract.14. Rejection and Rehearing14.1 Material tested by the purchaser that fails to conform tothe requirements of this specification may be rejected. Rejec-tion should be reported to the producer or supp

32、lier promptlyand in writing. In case of dissatisfaction with the results of thetest, the producer or supplier may make claim for a rehearing.15. Certification15.1 When specified in the purchase order or contract, amanufacturers certification shall be furnished to the purchaserstating that material h

33、as been manufactured, tested, and in-spected in accordance with this specification, and that the testresults on representative samples meet specification require-ments. When specified in the purchase order or contract, areport of the test results shall be made.16. Product Marking16.1 Each piece of m

34、aterial12 in. (12.7 mm) or over indiameter shall be marked with the specification number, alloy,heat number, manufacturers identification, and size. Themarkings shall have no deleterious effect on the material or itsperformance and shall be sufficiently stable to withstandnormal handling.16.2 Each b

35、undle or shipping container shall be markedwith the name of the material; this specification number; alloy;the size; gross, tare, and net weight; consignor and consigneeaddress; contract or order number; and such other informationas may be defined in the contract or order.17. Keywords17.1 rod; UNS N

36、08320APPENDIX(Nonmandatory Information)X1. HEAT TREATMENTX1.1 Proper heat treatment during or subsequent to fabri-cation is necessary for optimum performance, and the manu-facturer shall be consulted for details.ASTM International takes no position respecting the validity of any patent rights assert

37、ed in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by t

38、he responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive

39、 careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM Interna

40、tional, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through

41、the ASTM website(www.astm.org).TABLE 4 Permissible Variations in Diameter and Out-of-Roundness of Finished RodsSpecified Diameter, in. (mm)Permissible Variations, in. (mm)DiameterOut of Roundness, maxPlus MinusHot-Finished, Annealed, and Descaled Rods516 to716 (7.9411.11), incl 0.012 (0.30) 0.012 (0.30) 0.018 (0.46)Over716 to58 (11.1115.87), incl 0.014 (0.36) 0.014 (0.36) 0.020 (0.51)Over58 to34 (15.8719.05), excl 0.016 (0.41) 0.016 (0.41) 0.024 (0.61)Hot-Finished, Annealed, and Ground or Turned Rods34 to 312 (19.0588.9), incl 0.010 (0.25) 0 0.008 (0.20)B 621 02 (2006)3