ASTM B221M-2012 Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars Rods Wire Profiles and Tubes (Metric) 《铝和铝合金挤压棒材杆材金属丝型材和管道的标准规格(公制)》.pdf
《ASTM B221M-2012 Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars Rods Wire Profiles and Tubes (Metric) 《铝和铝合金挤压棒材杆材金属丝型材和管道的标准规格(公制)》.pdf》由会员分享,可在线阅读,更多相关《ASTM B221M-2012 Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars Rods Wire Profiles and Tubes (Metric) 《铝和铝合金挤压棒材杆材金属丝型材和管道的标准规格(公制)》.pdf(15页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: B221M 12Standard Specification forAluminum and Aluminum-Alloy Extruded Bars, Rods, Wire,Profiles, and Tubes (Metric)1This standard is issued under the fixed designation B221M; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revi
2、sion, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope*1.1 This specification
3、 covers aluminum and aluminum-alloyextruded bars, rods, wires, profiles, and tubes in the aluminumalloys (Note 1) and tempers shown in Table 2.NOTE 1Throughout this specification the use of the term alloy in thegeneral sense includes aluminum as well as aluminum alloy.NOTE 2For rolled or cold-finish
4、ed bars and rods refer to SpecificationB211M, for drawn seamless tube used in pressure applications, Specifi-cation B210M, for structural pipe and tube, Specification B429/B429M,and for seamless pipe and tube used in pressure applications, SpecificationB241/B241M.NOTE 3Structural pipe and tube produ
5、ced in accordance with thisspecification is not intended for fluid-carrying applications involvingpressure. Refer to either Specification B210M or B241/B241M,asappropriate, for seamless pipe and tube used in fluid-carrying applicationsinvolving pressure.1.2 Alloy and temper designations are in accor
6、dance withANSI H35.1/H35.1M. The equivalent Unified NumberingSystem alloy designations are those of Table 1 preceded byA9,for example, A91100 for Aluminum 1100 in accordance withPractice E527.1.3 For acceptance criteria for inclusion of new aluminumand aluminum alloys in this specification, see Anne
7、x A2.1.4 This specification is the metric counterpart of Specifi-cation B221.1.5 The values stated in SI are to be regarded as standard.No other units of measurement are included in this specifica-tion.2. Referenced Documents2.1 The following documents of the issue in effect on thedate of material p
8、urchase form a part of this specification to theextent referenced herein:2.2 ASTM Standards:2B210M Specification for Aluminum and Aluminum-AlloyDrawn Seamless Tubes (Metric)B211M Specification for Aluminum and Aluminum-AlloyBar, Rod, and Wire (Metric)B241/B241M Specification for Aluminum and Aluminu
9、m-Alloy Seamless Pipe and Seamless Extruded TubeB429/B429M Specification for Aluminum-Alloy ExtrudedStructural Pipe and TubeB557M Test Methods forTensionTestingWrought and CastAluminum- and Magnesium-Alloy Products (Metric)B594 Practice for Ultrasonic Inspection of Aluminum-Alloy Wrought Products fo
10、r Aerospace ApplicationsB660 Practices for Packaging/Packing of Aluminum andMagnesium ProductsB666/B666M Practice for Identification Marking of Alumi-num and Magnesium ProductsB807/B807M Practice for Extrusion Press Solution HeatTreatment for Aluminum AlloysB881 Terminology Relating toAluminum- and
11、Magnesium-Alloy ProductsB918 Practice for Heat Treatment of Wrought AluminumAlloysB945 Practice forAluminumAlloy Extrusions Press Cooledfrom an Elevated Temperature Shaping Process for Pro-duction of T1, T2, T5 and T10Type TempersE29 Practice for Using Significant Digits in Test Data toDetermine Con
12、formance with SpecificationsE34 Test Methods for Chemical Analysis of Aluminum andAluminum-Base AlloysE527 Practice for Numbering Metals and Alloys in theUnified Numbering System (UNS)1This specification is under the jurisdiction of ASTM Committee B07 on LightMetals and Alloys and is the direct resp
13、onsibility of Subcommittee B07.03 onAluminum Alloy Wrought Products.Current edition approved Jan. 15, 2012. Published March 2012. Originallyapproved in 1979. Last previous edition approved in 2007 as B221M 07. DOI:10.1520/B0221M-12.2For referenced ASTM standards, visit the ASTM website, www.astm.org
14、, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C7
15、00, West Conshohocken, PA 19428-2959, United States.TABLE 1 Chemical Composition LimitsA,B,CNOTEIn case of a discrepancy between the values listed inTable 1 and those listed in the “InternationalAlloy Designations and Chemical CompositionLimits for Wrought Aluminum and Wrought Aluminum Alloys”(known
16、 as the “Teal Sheets”), the composition limits registered with the AluminumAssociation and published in the “Teal Sheets” should be considered the controlling composition. The “Teal Sheets” are available at http:/www.aluminum.org/tealsheets.Alloy Silicon Iron CopperManga-neseMagne-siumChromium Zinc
17、Titanium VanadiumOther ElementsDAluminumEach TotalE1060 0.25 0.35 0.05 0.03 0.03 . 0.05 0.03 0.05 0.03 . 99.60 minF1100 0.95 Si + Fe 0.050.20 0.05 . . 0.10 . . 0.05G0.15 99.00 minF2014 0.501.2 0.7 3.95.0 0.401.2 0.200.8 0.10 0.25 0.15H. 0.05H0.15 remainder2024 0.50 0.50 3.84.9 0.300.9 1.21.8 0.10 0.
18、25 0.15H. 0.05H0.15 remainder2219 0.20 0.30 5.86.8 0.200.40 0.02 . 0.10 0.020.10 0.050.15 0.05I0.15Iremainder3003 0.6 0.7 0.050.20 1.01.5 . . 0.10 . . 0.05 0.15 remainderAlclad 3003 . 3003 Clad with 7072 alloy . . . . . . . .3004 0.30 0.7 0.25 1.01.5 0.81.3 . 0.25 . . 0.05 0.15 remainder3102 0.40 0.
19、7 0.10 0.050.40 . . 0.30 0.10 . 0.05 0.15 remainder5052 0.25 0.40 0.10 0.10 2.22.8 0.150.35 0.10 . . 0.05 0.15 remainder5083 0.40 0.40 0.10 0.401.0 4.04.9 0.050.25 0.25 0.15 . 0.05 0.15 remainder5086 0.40 0.50 0.10 0.200.7 3.54.5 0.050.25 0.25 0.15 . 0.05 0.15 remainder5154 0.25 0.40 0.10 0.10 3.13.
20、9 0.150.35 0.20 0.20 . 0.05 0.15 remainder5454 0.25 0.40 0.10 0.501.0 2.43.0 0.050.20 0.25 0.20 . 0.05 0.15 remainder5456 0.25 0.40 0.10 0.501.0 4.75.5 0.050.20 0.25 0.20 . 0.05 0.15 remainder6005 0.60.9 0.35 0.10 0.10 0.400.6 0.10 0.10 0.10 . 0.05 0.15 remainder6005A 0.500.9 0.35 0.30 0.50J0.400.7
21、0.30J0.20 0.10 . 0.05 0.15 remainder6020K0.400.9 0.50 0.300.9 0.35 0.61.2 0.15 0.20 0.15 . 0.05 0.15 remainder6041L0.500.9 0.150.7 0.150.6 0.050.20 0.81.2 0.050.15 0.25 0.15 . 0.05 0.15 remainder6042M0.501.2 0.7 0.200.6 0.40 0.71.2 0.040.35 0.25 0.15 . 0.05 0.15 remainder6060 0.300.6 0.100.30 0.10 0
22、.10 0.350.6 0.5 0.15 0.10 . 0.05 0.15 remainder6061N0.400.8 0.7 0.150.40 0.15 0.81.2 0.040.35 0.25 0.15 . 0.05 0.15 remainder6063 0.200.6 0.35 0.10 0.10 0.450.9 0.10 0.10 0.10 . 0.05 0.15 remainder6064O0.400.8 0.7 0.150.40 0.15 0.81.2 0.050.14 0.25 0.15 . 0.05 0.15 remainder6066 0.91.8 0.50 0.71.2 0
23、.61.1 0.81.4 0.40 0.25 0.20 . 0.05 0.15 remainder6070 1.01.7 0.50 0.150.40 0.401.0 0.501.2 0.10 0.25 0.15 . 0.05 0.15 remainder6082 0.71.3 0.50 0.10 0.401.0 0.61.2 0.25 0.20 0.10 . 0.05 0.15 remainder6105 0.61.0 0.35 0.10 0.15 0.450.8 0.10 0.10 0.10 . 0.05 0.15 remainder6162 0.400.8 0.50 0.20 0.10 0
24、.71.1 0.10 0.25 0.10 . 0.05 0.15 remainder6262 0.400.8 0.7 0.150.40 0.15 0.81.2 0.040.14 0.25 0.15 . 0.05P0.15Premainder6351 0.71.3 0.50 0.10 0.400.8 0.400.8 . 0.20 0.20 . 0.05 0.15 remainder6360 0.350.8 0.100.30 0.15 0.020.15 0.250.45 0.05 0.10 0.10 . 0.05 0.15 remainder6463 0.200.6 0.15 0.20 0.05
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMB221M2012STANDARDSPECIFICATIONFORALUMINUMANDALUMINUMALLOYEXTRUDEDBARSRODSWIREPROFILESANDTUBESMETRIC

链接地址:http://www.mydoc123.com/p-460659.html