ASD-STAN PREN 4165-003-2014 Aerospace series Connectors electrical rectangular modular Operating temperature 175 continuous Part 003 Modules series 2 and series 3 Product standard .pdf

《ASD-STAN PREN 4165-003-2014 Aerospace series Connectors electrical rectangular modular Operating temperature 175 continuous Part 003 Modules series 2 and series 3 Product standard .pdf》由会员分享，可在线阅读，更多相关《ASD-STAN PREN 4165-003-2014 Aerospace series Connectors electrical rectangular modular Operating temperature 175 continuous Part 003 Modules series 2 and series 3 Product standard .pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、ASD-STAN STANDARD NORME ASD-STAN ASD-STAN NORM prEN 4165-003 Edition P 3 April 2014 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Rue Montoyer 10 - 1000 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 775 8131 - www.asd-stan.orgICS: 49.060 Supersedes edition

2、 P 2 of July 2006 and will supersede EN 4165-003:2008 Descriptors: ENGLISH VERSION Aerospace series Connectors, electrical, rectangular, modular Operating temperature 175 C continuous Part 003: Modules series 2 and series 3 Product standard Srie arospatiale Connecteurs lectriques rectangulaires modu

3、laires Temprature dutilisation 175 C continu Partie 003 : Modules srie 2 et srie 3 Norme de produit Luft- und Raumfahrt Elektrischer Rechtecksteckverbinder in modularer Bauweise Betriebstemperatur 175 C konstant Teil 003: Modul Serie 2 und Serie 3 Produktnorm This “Aerospace Series“ Prestandard has

4、been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subs

5、equent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of ASD-STAN, it will be submit

6、ted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing an

7、y national standards conflicting with the EN. Edition approved for publication 1stApril 2014 Comments should be sent within six months after the date of publication to ASD-STAN Electrical Domain Copyright 2014 by ASD-STAN prEN 4165-003:2014 (E) 2 Contents Page Foreword 2 1 Scope 3 2 Normative refere

8、nces 3 3 Terms and definitions . 3 4 Required characteristics . 4 5 Male and female module coding 8 6 Main general characteristics 9 7 Designation 10 8 Marking . 12 9 Technical specification . 12 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Electrical Domain.

9、After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. prEN 4165-003:2014 (E) 3 1 Scope This standard specifies the characteristics of module in the family of modular connector c

10、oupled by central threaded coupling, or rack and panel or push-pull latching mechanism. For contacts and fillers plug associated see EN 4165-002. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application

11、. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 3155-002, Aerospace series Electrical contacts used in elements of connection Part 002: List and utilization of contacts EN 3155-070, A

12、erospace series Electrical contacts used in elements of connection Part 070: Contacts, electrical, male, type A, crimp, class S Product standard EN 3155-071, Aerospace series Electrical contacts used in elements of connection Part 071: Contacts, electrical, female, type A, crimp, class S Product sta

13、ndard EN 4165-001, Aerospace series Connectors, electrical, rectangular, modular Operating temperature 175 C continuous Part 001: Technical specification EN 4165-002, Aerospace series Connectors, electrical, rectangular, modular Operating temperature 175 C continuous Part 002: Specification of perfo

14、rmance and contact arrangements 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 4165-001 apply. prEN 4165-003:2014 (E) 4 4 Required characteristics 4.1 Male module interface dimensions Series 2 and series 3 See Figure 1 and Table 1. Dimensions are in

15、millimetres. Key 1 Polarizing keys, see Figure 5. 4 Zone of contact (module grounded) 2 Optional design for sealed version 5 2,00 1,00 point of sealing feature 3 Interfacial seal, see Figure 3. 6 Grommet Figure 1 Male module series 2 and 3 Table 1 Male module series 2 and 3 dimensions Size A C Mass

16、without contacts g max. max. max. 22-20-16-12 16,46 13,35 3,0 8 18,70 11,65 2,3 prEN 4165-003:2014 (E) 5 4.2 Female module interface dimensions Series 2 and series 3 See Figure 2 and Table 2. Dimensions are in millimetres. Key 1 Polarizing keys see Figure 5. 4 Zone of contact (module grounded) 2 Opt

17、ional design for sealed version 5 2,00 1,00 point of sealing feature 3 Socket contact cavity see Figure 4. 6 Grommet Figure 2 Female series 2 and 3 module Table 2 Female module series 2 and 3 dimensions Size A max. B C max. series 2 series 3 series 2 series 3 22-20-16-12 22,40 30,96 17,16 to 17,40 2

18、5,72 to 25,96 13,35 8 33,20 11,65 prEN 4165-003:2014 (E) 6 4.3 Male and female module size 08 contact Grommet design For series 2 and series 3. Male module Female module Key 1 Module grommet 2 Sealing sleeve Figure 3 Male and female module size 08 prEN 4165-003:2014 (E) 7 4.4 Blank module series 2 a

19、nd series 3 Instead of male or female modules: Normal version: 3 g max.; or Lightweight version: 1,5 g max. Figure 4 Blank module 4.5 Module interface dimensions See EN 4165-001, Figures 20 and 21. prEN 4165-003:2014 (E) 8 5 Male and female module coding See Figures 5 and 6. Standard position N Posi

20、tion A Position B Position C Position D Figure 5 Male and female module polarization prEN 4165-003:2014 (E) 9 Position E Position F NOTE Modules polarized E and F have no shell corresponding. Figure 6 Male and female module polarization 6 Main general characteristics See EN 4165-002. prEN 4165-003:2

21、014 (E) 10 7 Designation 7.1 Electrical modules EXAMPLE Description block ELECTRICAL MODULES Identity block EN4165A04G161NA Number of the basic standard Module series (see EN 4165-002) Series 2 A Series 3 B (not for blank module) Module arrangements and grounding module device (see EN 4165-002) Dash

22、 No grounding G Grounding L No grounding, quadrax contact Q Grounding, quadrax contact A No grounding, grey grommet for EN 3155-070 / EN 3155-071 contacts Y Blue grommet, shunted, female contacts Z Brown grommet, shunted, male contacts Peripherical sealing and resistance to fuel Type 1 Without perip

23、herical sealing and standard resistance to fuel Type 2 With peripherical sealing and standard resistance to fuel Type 3 Without peripherical sealing and reinforced resistance to fuel Type 4 With peripherical sealing and reinforced resistance to fuel Polarization (see Figure 5) N Normal, or A, B, C,

24、D, E, F. Module and contact delivery (see Table 3) NOTE 1 If necessary, the code I9005 shall be placed between the description block and the identity block. NOTE 2 The previously used designation (e.g.: EN4165-04G16A1NA) is inactive for new design and should not be used as designation anymore. prEN

25、4165-003:2014 (E) 11 Table 3 Types of contacts and delivery modules Modules type Contact code delivery A B M F C D Male module Delivered without contact Female module Delivered without contact Male module Female module Male module Female module Delivered with contacts with standard barrels a Deliver

26、ed with contacts with standard barrels a Delivered with contacts with reduced / enlarged barrel a Delivered with contacts with reduced / enlarged barrel a EN3155-008M2222 EN3155-008M2020 EN3155-008M1616 EN3155-008M1212 EN3155-065M0808A EN3155-003F2222 EN3155-003F2020 EN3155-003F1616 EN3155-003F1212

27、EN3155-066F0808A EN3155-xxxx2018 b EN3155-xxxx1614 c EN3155-xxxx1210 d; e EN3155-065M0810A EN3155-xxxx2018 b EN3155-xxxx1614 c EN3155-xxxx1210 d; e EN3155-066F0810A G N/A N/A N/A C Male module Female module N/A N/A L - Q Delivered with quadrax contacts a Delivered with quadrax contacts a EN3155-074x

28、x e EN3155-075xx e Male module Female module Male module Female module A Delivered with following contacts a Delivered with following contacts a Delivered with following contacts a Delivered with following contacts a EN3155-070xx e EN3155-071xx e EN3155-070xx e EN3155-071xx e Shunted, female module

29、Y N/A Delivered with following contacts a N/A N/A EN3155-082xx e Shunted, male module Z Delivered with following contacts a N/A N/A N/A EN3155-008M2222 e without selective gold plating a See EN 3155-002. b Only affects arrangements with size 20 contacts. c Only affects arrangements with size 16 cont

30、acts. d Only affects arrangements with size 12 contacts. e Under standardization. prEN 4165-003:2014 (E) 12 7.2 Blank module Blank module is available for all shells (receptacles and plugs) instead of male and female standard modules, in series 2 and series 3. EXAMPLE Description block BLANK MODULE

31、Identity block EN4165-1NL Number of the basic standard Peripherical sealing unsealed 1 sealed 2 Polarization N Normal only Version Blank Normal version L Lightweight version 8 Marking Marking shall be applied to the module. This marking shall include: The identity block as defined in suitable product standard; The date of manufacture (yearweek); The manufacturers name or trade mark. 9 Technical specification See EN 4165-001.