ASD-STAN PREN 3646-010-2014 Aerospace series Connectors electrical circular bayonet coupling operating temperature 175 or 200 continuous Part 010 Protective cover for plug Product .pdf

《ASD-STAN PREN 3646-010-2014 Aerospace series Connectors electrical circular bayonet coupling operating temperature 175 or 200 continuous Part 010 Protective cover for plug Product .pdf》由会员分享，可在线阅读，更多相关《ASD-STAN PREN 3646-010-2014 Aerospace series Connectors electrical circular bayonet coupling operating temperature 175 or 200 continuous Part 010 Protective cover for plug Product .pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、ASD-STAN STANDARD NORME ASD-STAN ASD-STAN NORM prEN 3646-010 Edition P 2 May 2014 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Rue Montoyer 10 - 1000 Brussels - Tel. 32 2 775 8126 - Fax. 32 2 775 8131 - www.asd-stan.org ICS: 49.060 Supersedes edition P 1

2、of November 2001 and will supersede EN 3646-010:2006 Descriptors: Aeronautical industry, aircraft equipment, electrical connection unit, electrical connector, characteristics marking ENGLISH VERSION Aerospace series Connectors, electrical, circular, bayonet coupling, operating temperature 175 C or 2

3、00 C continuous Part 010: Protective cover for plug Product standard Srie arospatiale Connecteurs lectriques circulaires accouplement par baonnettes, temprature dutilisation 175 C ou 200 C continu Partie 010 : Bouchon de vol pour fiche Norme de produit Luft- und Raumfahrt Elektrische Rundsteckverbin

4、der mit Bajonettkupplung, Betriebstemperatur 175 C oder 200 C konstant Teil 010: Schutzkappe fr freien Steckverbinder Produktnorm This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization).

5、 It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is

6、affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full

7、 European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition approved for publication 1st May 2014 Comments should be sent within six mon

8、ths after the date of publication to ASD-STAN Electrical Domain Copyright 2014 by ASD-STAN prEN 3646-010:2014 (E) 2 Contents Page Foreword 2 1 Scope 3 2 Normative references 3 3 Terms and definitions . 3 4 Required characteristics . 3 5 Designation 6 6 Marking . 7 7 Technical specification . 7 Forew

9、ord This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Electrical Domain. After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. prEN 3646-010:2014 (E) 3

10、 1 Scope This standard defines the characteristics of protective covers for plugs in the family of bayonet coupling circular connectors, intended for use in an operating temperature range of 65 C to 175 C or 200 C continuous. It applies to models defined in Table 2. For plugs associated with these p

11、rotective covers, see EN 3646-008. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the refer

12、enced document (including any amendments) applies. EN 3646-001, Aerospace series Connectors, electrical, circular, bayonet coupling, operating temperature 175 C or 200 C continuous Part 001: Technical specification EN 3646-002, Aerospace series Connectors, electrical, circular, bayonet coupling, ope

13、rating temperature 175 C or 200 C continuous Part 002: Specification of performance and contact arrangements EN 3646-008, Aerospace series Connectors, electrical, circular, bayonet coupling, operating temperature 175 C or 200 C continuous Part 008: Plug Product standard 3 Terms and definitions For t

14、he purposes of this document, the terms and definitions given in EN 3646-001 apply. 4 Required characteristics 4.1 Dimensions and mass See Figure 1 and Table 1. Dimensions and tolerances are in millimetres, they apply after surface treatment. Interface dimensions, see EN 3646-001. prEN 3646-010:2014

15、 (E) 4 Key 1 B (optional) 2 Sealing gasket shall be bonded or mechanically retained in protective cover 3 Chain or rope (withstand the 200 C maximum operating temperature) 4 Fastener (chain or rope shall rotate freely on the fastener) 5 Attachment type with ring, see Table 3. 6 Attachment type with

16、eyelet, see Table 3. 7 Eyelet hole diameter 4,240,130,25Figure 1 Plug protective cover prEN 3646-010:2014 (E) 5 Table 1 Plug protective cover dimensions Housing size A B C D E F G M R Mass g max. max. 0,02 0,13 min. 6,25 max. max. min. max. 08 18,26 16,05 12,02 8,008,84 10,10 10,60 127,50 19,84 15,0

17、0 12,45 12 10 21,43 18,05 14,99 15,70 16 12 25,40 22,05 19,05 18,85 22 14 28,57 24,05 22,23 22,10 24 16 31,75 27,05 25,40 25,50 28 18 34,92 30,05 28,58 27,35 33 20 38,10 33,05 31,75 9,5010,42 11,60 12,06 21,44 16,71 30,40 38 22 41,27 36,05 34,93 33,30 42 24 44,45 44,05 38,10 22,22 36,80 49 4.2 Mater

18、ial and surface treatment Protective cover shell See Table 2. Chain Stainless steel or aluminium. Fastener Stainless steel or brass. Ring Stainless steel or aluminium. Eyelet Stainless steel or brass. 4.3 Main general characteristics See EN 3646-002. 4.4 Possible combinations of protective covers an

19、d connectors See EN 3646-002. prEN 3646-010:2014 (E) 6 5 Designation EXAMPLE Description block PROTECTIVE COVER, ELECTRICAL CONNECTOR Identity block EN3646A4D10 Number of the basic standard Model (see Table 2) Protective cover for plug (see EN 3646-002) Type of attachment (see Table 3) Housing size

20、(see Table 1) NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. Table 2 Protective cover models Model DescriptionA Protective cover for plug in black anodized aluminium alloy Maximum operating temperature 200 C continuous RS Protective cover for

21、plug in nickel-plated aluminium alloy Maximum operating temperature 200 C continuous WS Protective cover for plug in olive green cadmium plated aluminium alloy Maximum operating temperature 175 C continuous Table 3 Type of attachment Attachment type Description C Chain and eyelet D Chain and ring E

22、Rope with PTFE jacket and eyelet F Rope with PTFE jacket and ring prEN 3646-010:2014 (E) 7 6 Marking Unless there are other specific contractual requirements, the marking shall include. 6.1 Marking on the product the manufacturers part number corresponding to the identity block as defined in Clause

23、5; the date of manufacture (year, week); the manufacturers name or trade mark. 6.2 Marking on the individual packaging the identity block as defined in Clause 5; the corresponding manufacturers part number; the date of manufacture (year, week); the manufacturers name or trade mark. 7 Technical specification See EN 3646-001.