ARMY MIL-T-43512 B-1986 TENTS MISSILE SYSTEM EQUIPMENT CONSOLE (HIGH-POWER ILLUMINATOR HAWK)《导弹系统装备控制台帐篷(高能照明HAWK)》.pdf

《ARMY MIL-T-43512 B-1986 TENTS MISSILE SYSTEM EQUIPMENT CONSOLE (HIGH-POWER ILLUMINATOR HAWK)《导弹系统装备控制台帐篷(高能照明HAWK)》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-T-43512 B-1986 TENTS MISSILE SYSTEM EQUIPMENT CONSOLE (HIGH-POWER ILLUMINATOR HAWK)《导弹系统装备控制台帐篷(高能照明HAWK)》.pdf（31页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-T-935LZB 83 W 7777706 0379370 7 MILITARY S PECIF IC AT1 ON c-p3-40 MIL-T-43512B 5 December 1986 SUPERSEDING MIL-T 435128 7 December 1970 TENIIS, MISSILE SYSTEM EQUIPMENT CONSOIE, (HIGH-POWER ILLUMINATOR BAWK) t - R This specification is approved for use by all Departments and Agencies of the Dep

2、artment of Defense. I -* 1. SCOPE 1.1 Scope. This document covers two frame-supported console tents for use with the Hawk Missile System. A cover for each tent with its frame components is furnished to afford protection during storage and transport 1.2 Classification. The console tents consist of th

3、e following items: Tent, Console, High-Power Illuminator, Hawk System, Front Tent, Console, High-Power. Illuminator, Hawk System, Aft - 2. APPLICABLE DOCUMENTS m 2.1 Government documents. 2.1.1 Documents. The following documents form a part of this document to the extent specified herein. Unless oth

4、erwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (WDISS) and supplement thereto, cited in the solicitation. SPECIFICATIONS FEDERAL T-T-871 - Twine, Cotton, Wrapping T-T- 91 1 - Twine, Fibrous, Jute V

5、-F-106 - Fasteners, Slide, Interlocking Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to U.S. Army Natick Research, Development, and Engineering Center, Natick, MA 01760-5014, by using the self -a

6、ddr es s ed Standard i za t ion Do cumen t Im pr ovemen t Proposal (DD Form 1426) appearing at the end of this document or by letter. - AMSC N/A FSC 8340 DISTRIBUTION STATEMENT A. Approved for public release; distribution is un THIS DOCUMENT CONTAINS PAGES. m,ted. Provided by IHSNot for ResaleNo rep

7、roduction or networking permitted without license from IHS-,-,-VIL-T-Lt35LZB 3 M 7797706 0374373 7 V-T-285 TT-P-595 UIJ-T-94 ccc-c-429 CCC-C-467 DDD-L-20 PPP-B-601 PPP-B-636 MILITARY MIL-C-496 MIL-W-530 MIL-B-54 3 MIL-R-167 O MIL-L- 17 O9 MIL-S -1 73 4 MIL-C-2399 MIL-C -1 07 9 9 MIL-G- 16 4 91 MIL-F

8、-2 1840 MIL-R-30500 MIL -L-3 50 7 8 MIL-T -40 62 5 MIL-C-43256 MIL-T -4 3 5 6 6 MIL-C-43 627 ! MIL -W-4 4 049 MIL-A-52194 STANDARDS FEDERAL FED-STD-191 FED-STD-7 51 MIL-T-43 51 2B - Thread, Polyester - Preservative Coating, Canvas - Tape, EmboTsing - Cloth, Osqaburg, Cotton - Cloth, Burlap, Jute (or

9、 Kenaf) - Label; For Clothing, Equipage and Tentage - Boxes, Wood, Cleated-Plywood - Boxes, Shipping, Fiberboard (General Use) - Clips, End, Strap - Webbing, Textile, Cotton General Purpose, Natural or in Colors - Buckles, Tongueless and Web Strap - Rope, Tent-Lay - Lines, Tent - Slips, Tent Line -

10、Cement, Liquid, Tent Patching - Cloth, Coated, Cotton, Vinyl Coated, Fire and Mildew Resistant - Grommet, Metallic - Fastener Tapes, Hook and Pile, Synthecic - Rope, Polyester - Loads, Unit: Preparation of Semiperishable Subsistence Items; Clothing, Personal Equipment and Equipage; General Specifica

11、tion For - Tubing, Bias Sewn (Burlap or Osnaburg) Cloth - Cord, Polyester, Solid Braid - Tape, Textile, Cotton, General Purpose, Natural - Cloth, Duck, Cotton, Plied Yarns, Fire, Water, or in Colors Weather and Mildew Resistant Treated, Lightdry Finish General Purpose, Natural or in Colors P o1 yes

12、ter ) - Webbing, Textile and Tape, Textile, Polypropylene, - Adhesive, Epoxy (For Bonding Glass Reinforced - Textile Test Methods - Stitches, Seams, and Stitchings 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-T-43512B 83 W 9779906 0374372 O

13、= 5-4-1103 5-4-1 104 5-4-1 105 5-4-1116 5-4-1 1 17 5-4-1 118 5-4-1 119 5-4-1 120 5-4-1121 5-4-1 12 2 5-4-1 123 5-4-1 124 5-4-1 12 5 5-4-1 12 6 5-4 -1 127 5-4-1128 5-4-11 29 5-4-1130 5-4-1 131 5-4-1132 5-4-1 133 5-4-1134 5-4-1 13 5 MIL-T -43 51 2B MILITARY MIL-STD-105 MIL-STD-129 - Marking for Shipme

14、nt and Storage MS-27183 - Washer, Flat-Round, Steel, Cadmium Plated, MS-27980 - Fasteners, Snap, Style 2 (Regular Wire Spring MS-35307 - Screw, Cap, Hexagon (Finished Hexagon Bolt), MS-51967 - Nut, Plain, Hexagon-Carbon, Steel, Cadmium - Sampling Procedures and Tables for Inspection by Attributes Ge

15、neral Purpose Clamp Type) Steel Corrosion Resisting, Passivated UNC-2A Plated, UNC-2B DRAWINGS U.S. ARMY NATICK RESEARCH, DEVELOPMENT, AND ENGINEERING CENTER - Frame, Tent, High Power Illuminator, Front - Corner Support Assembly and Details - Pallet Adapter Assembly and Details - Tents, Console, Hig

16、h Power Illuminator, Hawk - Front Wall Assembly - Front Wall Sections and Details - Piece “A“ and Piece “B“ Assemblies and Details - Left Wall Assembly Complete Systems, Front; Assembly Complete System, Aft; Assembly Complete 3 Provided by IHSNot for ResaleNo reproduction or networking permitted wit

17、hout license from IHS-,-,-II_ _ -_- MIL-T-43512B 3 W 9777706 0374373 2 m MIL-T-43 51 2B 5-4-1 13 6 - Ground Cloth Assembly, Miscellaneous Details 5-4-1137 - Cover Assembly 5-4-1 138 - Erection Instructions . (Copies of documents required by contractors in connection with specific acquisition functio

18、ns should be obtained from the contracting activity or as directed by the contracting activity.) 2.1.2 Other Government documents. The following other Government documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues shall be those in effect on

19、the date of the solicitation. Department of the Army Field Manual FM 10-16 - General Repair of Tents, Canvas and Webbing (Copies of documents required by contractors in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting a

20、ctivity.) 2.2 Other publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DOD adopted shall be those listed in the issue of the WDZSS specified in the solicitation. specified, the issues of

21、 documents not listed in the DODISS shall be the issues of the nongovernment documents which are current on the date of the solicitation. Unless otherwise AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) D 1788 - Rigid Acrylonitrile-Butadiene-Styrene (ABS) Plastics D 3951 - Standard Practice for Co

22、mmercial Packaging (Application for copies should be addressed to the American Society For Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) (Technical society and technical association documents are generally available for reference from libraries. They are also distributed among te

23、chnical groups and using Federal agencies.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document shall take precedence. Nothing in this document, however, shall supersede applicable laws and regulations unles

24、s a specific exemption has been obtained. 4 - Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-435129 3 7777706 037437Li 4 MIL-T-43 51 2B 3. REQUIREMENTS o 3.1 First article. When specified in,the contract or purchase order, a sample shall be su

25、bjected to first article inspection (see 4.3, 6.2, and 6.3). 3.2 Materials and components. (See 6.5) 3.2.1 Cloth, duck, cotton. The cotton cloth used for the tent shall conform to MIL-C-43627, and the color shall be Olive Drab 7. ?- 3.2.2 Cloth, coated. Cloth used for the tent and frame cover and fo

26、r roof reinforcement panels shall conform to type II, class 1, Olive Drab 7 of MIL-C-10799. 3.2.3 Cloth, polyester. The polyester cloth used for the light ports shall be water repellent, shade natural, and shall conform to the following requirements when tested as specified in 4.4.1.1: a. Physical p

27、roperties as follows: Fiber - Polyester Weave - Plain, 1 by 1 Texture, threads per inch; minimum Warp - 80 Filling - 64 Warp - 290 Filling - 265 Breaking strength (grab) pounds, minimum - Weight - 5.5 f 0.5 oz. per sq. yd. Water resistance - spray rating 90, 90, 80) (three determinations) b. Finishi

28、ng properties as follows: (1) A water repellent of the silicone type is specified. However, other water-repellent compounds may be used if approved by the contracting officer . color shall be natural; the fabric shall have a maximum air permeability of 1.5 CU. ft. per minute per sq. ft., and a minim

29、um luminous transmission of 40 percent. (2) The fabric shall be scoured, calendered, and heat set. The )c 3-2.4 Tape, textile, cotton. The tape shall conform to type I, class 4, 3/4 inch, 1 1/2-inch, and 2-inch widths of MIL-T-43566 and shall be Olive Drab 7. class 4, Olive Drab 7 of MIL-W-44049. Al

30、ternatively, the tape shall be polypropylene conforming to type I, 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_-_.I- MIL-T-43512B 3 - 777770b 0374375 b 9 MIL -T-4 3 51 2B * 3.2.5 Webbing, textile, cotton. The webbing shall conform to type IIB,

31、 class 4, 1-inch width of MIL-W-530 and shall be Olive Drab 7. the webbing shall be polypropylene conforming to type IIb, class 4, Olive Drab 7 of MIL-W-44049. Alternatively, 3.2.6 Thread, polyester. The thread shall be type I, class 1, sub-class B, dyed to match shade S-1 (Cable No. 66022) of V-T-2

32、85. The dyed thread shall show fastness to weathering equal to or better than a standard shade sample (see 6.4). If no standard shade sample is available, the dyed thread shall show good fastness to weathering. Thread sizes shall be as follows: a. For all stitching except bartacking, stitching on co

33、ver, and stitching indicated by “Z“ on the drawings, use size F for needle and bobbin. be For all stitching on cover, use size FF for needle and bobbin. c. For stitching indicated by “Z“ on the drawings, use size F for needle and size E for looper. d. For bartacking, use size E. 3.2.7 Grommets, meta

34、llic. Rolled rim grommets with spur washers shall conform to type III, class 3, sizes 2 and 4 of MIL-G-16491. * 3.2.8 Fasteners, slide, interlocking. Slide fasteners shall conform to type III, style 1, with wire stirrup pull on each side, conforming to size H of V-F-106. Slide fastener chains and sl

35、iders shall be fabricated of brass. Alternatively, the slide fastener chain shall be polyester continuous monofilament in a ladder or coil type configuration, conforming to requirements in 3.2.8.1. Color of the chain, slider, pull, and stops shall approximately match the tape color. 3.2.8.1 Length.

36、The length of slide fastener chains shall be such that, after the slide fastener is sewed on, the tape shall not be puckered and the slider shall operate freely. 3.2.8.2 Tape. Slide fastener tape shal be dyed to match Olive Drab S (Cable No. 66519) and shall be water-repellent and mildew-resistant t

37、reated. The color of the tape after treatment will be considered acceptable. The tape shall show good fastness to weathering. 3.2.9 Fastener tape, hook and pile. Nylon hook-and-pile fastener tapes shall be dyed to match Olive Green 106 and shall conform to type II, 1-inch and %inch widths of MIL-F-2

38、1840. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-935L2B 3 m 9999906 0399396 m n 3.2.10 Rope, tent-lay. Tent-lay rope used in the securing lug shall conform to type I, class 2, 1/4-inch diameter of MIL-R-1670. Alternatively, tent-lay rope

39、 shall conform to polyester rope of 1/4-inch diameter of MIL-R-30500, and the color shall be Olive Drab 7. * 3.2.11 Lines, tent. The tent lines shall conform to class A of MIL-L-1709 or polyester rope conforming to MIL-R-30500, in the following types: I - Footstep XV - Reefing line XXVIII - Guy line

40、 3.2.12 Slips, tent line. Tent line slips shall conform to type II of MIL-S-173 4. 3.2.13 Clip, end, strap. End clips shall conform to type I, class 1 or 2, size 1 inch of MIL-C-496. 3.2.14 Buckle, tongueless. Buckles shall conform to type ZV, class 3 of MIL -B-5 4 3. 3.2.15 Fastener, snap. The snap

41、 fastener on the pocket of the cover shall consist of the following components:. button, conforming to MS 27980-1B; socket, conforming to MS 27980-6B; stud, conforming to MS 27980-7B; and eyelet, conforming to MS 27980-8B. 3.2.16 Eyelet tab, plastic. Plastic eyelet tabs for 1/4-turn stud fasteners s

42、hall be acrylic-nitrile butadiene styrene (ABS) (see 6.8a) conforming to ABS 5-2-2 of ASTM D 1788 in l/l6-inch thick sheet form. The material shall be Olive Drab 7 (or other dark color). Adulteration due to extenders, modifiers, or resin type other than ABS, excluding pigments, is limited to 5 perce

43、nt by weight. 3.2.17 Frame comDonents. 3.2.17.1 Supports. Plastic tube, square bar, and round bar support components shall be fabricated from reinforced fiberglass polyester resin material (see 6.8b). 3.2.17.2 Fittings. Plastic tees and elbows shall be fabricated from reinforced fiberglass epoxy res

44、in material (see 6.8). 3.2.17.3 Hardware, miscellaneous. The corrosion-resistant hexagon head cap screw shall conform to MS 35307-121; the steel hexagon nut shall conform to MS 51967-14; the cadmium plated steel washer shall conform to MS 27183-19; and the corrosion-resistant slotted truss head (or

45、binding head) machine screw, 1/4-28 UNF-LA by 1 1/2 inches long shall be standard comercial. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- - MIL-T-435128 3 777770b 0374377 T = MIL-T-43 51 2B 3-2-18 Cord, polyester. The solid braided polyester co

46、rd shall be 1/8-inch diameter conforming to MzL-C-43256. 3.2.19 Adhesive, epoxy. The two-part epoxy cement for joining fittings and supports shall conform to MIL-A-52194. 3.2.20 Tape, plastic, embossing. Plastic embossing tape used to identify components shall conform to class 2, color black of Vu-T

47、-94. 3-2-21 Ink, vinyl. Vinyl ink, color black with compatible thinner, for marking on coated fabric cover shall conform to Code No. 1A 26.17 of the Atlas Coatings Corp., or equivalent. 3.3 Construction. The construction shall conform to Drawings 5-4-1103 through 5-4-1105 and 5-4-1116 through 5-4-11

48、38 and as specified herein. 3.3.1 Stitchinn. machine. 3.3.1.1 Types of stitching. Stitching types shall conform to PED-STD-751 as follows: a. For all stitching except bartacking and stitching indicated by “Z“ For stitching indicated by “Z“ on drawings, use type 401, 5 to on drawings, use type 301, 5

49、 to 7 stitches per inch. b. 7 stitches per inch. on outside of tent or cover. Chain portion of stitching shall not appear C. For bartacking, use 7/8-inch bartack, plus or minus 1/16-inch long, with 1/8-inch bight and containtng 42 stitches. 3.3.1.2 Thread breaks. Thread breaks in stitching shall be overstitched not less than 1 inch at each break on stitch type 301 and not less than - 1 1/2 inches at each break