ARMY MIL-S-45352 F-1988 SEMITRAILER LOWBED TACTICAL 12 AND 25 TON《12吨和25吨作战用的拖车》.pdf

《ARMY MIL-S-45352 F-1988 SEMITRAILER LOWBED TACTICAL 12 AND 25 TON《12吨和25吨作战用的拖车》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-S-45352 F-1988 SEMITRAILER LOWBED TACTICAL 12 AND 25 TON《12吨和25吨作战用的拖车》.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-S-qS352F 23 m 7977706 0376883 O m I MIL-S-45352F 4 February 1988 SUPERSEDING MIL-S-4 53 5 2E 11 October 1978 MILITARY SPECIFICATION SEMITRAILER, LOWBED: TACTICAL, 12- AND 25-TON This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scop

2、e. This specification covers 12- and 25-ton lowbed semitrailers intended for use over all types of roads as tactical vehicles during military operations (see 6.1). 1.2 Classification. Semitrailers shall be classified by model, as follows (see 6.2) : . Model Description M172A1 Semitrailer, Lowbed, 25

3、-Ton, 4-Wheel. M270A1 Semitrailer, Lowbed, 12-Ton, 4-Wheel. 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications and standards. The following specifications and standards form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of the

4、se documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this docu

5、ment should be addressed to: US Army Tank-Automotive Command, ATTN: AMSTA-GDS, Warren, MI 48397-5000, by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC NIA FSC 2330 DISTRIBUTION STATEMENT A. Approved for

6、public release ; dis tribution is unlimited. THIS DOCUMENT CONTAINS 220 PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-45352F SPECIFICATIONS MILITARY MIL-P-5 14 MIL-T-12459 MIL-R-46164 MIL-(2-46 168 MIL-C-53039 MIL-V-62038 - Plates, Ide

7、ntification, Instruction and Marking, Blank - Tire, Pneumatic: for Military Ground Vehicles . - Rustproofing for Military Vehicles and Trailers. - Coating, Aliphatic Polyurethane, Chemical Agent Resistant . - Coating, Aliphatic Polyurethane, Simple Component, Chemical Agent Resistant. - Vehicles, Wh

8、eeled: Preparation for Shipment and Storage of. STANDARDS MILITARY MIL-STD-105 MIL-STD-130 MIL-STD-193 - Sampling Procedures and Tables for - Identification Marking of US Military - Painting Procedures and Marking for Inspection by Attributes. Property. Vehicles, Construction Equipment and Material

9、Handling Equipment. MIL-STD-209 - Slinging and Tie Down Provisions for Lifting and Tying Down Military Equipment. MIL-STD-642 - Identification Marking of Combat and Tactical Transport Vehicles. MIL- STD- 88 2 MIL-STD-456 62 - System Safety Program Requirements. - Calibration Systems Requirements. 2.

10、1.2 Drawings. The following drawings form a part of this specification to the extent specified herein. the issues shall be those in effect on the date of the solicitation, Unless otherwise specified, DRAWINGS ARMY 8358925 8736073 12355846 - Semitrailer, Wrecker, 12-Ton, 4-Wheel, - Semitrailer, Lowbe

11、d, 25-Ton, 4-Wheel, - Treatment and Paint Specifications for M270A1 . M172Al . Tactical Trailers. (Copies of specifications, standards, and drawings required by the contractors in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the co

12、ntracting activity.) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- . MIL-S-45352F 23 7797706 0376883 4 MIL-S-45352F a - I a - a 2.2 Order of precedence. In the event of a conflict between the text of this specification and the references cited h

13、erein (except for associated detail specifications, specification sheets or MS standards), the text of this specification shall take precedence. Nothing in this specification, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1

14、First article. Unless otherwise specified (see 6.2), the contractor shall furnish semitrailers, of specified model, which shall be subjected to first article inspection (see 4.3). properly marked with identifying information shall be representative of the semitrailers to be furnished to the Governme

15、nt. delivered to the Government shall conform to these samples in all of their pertinent physical and performance attributes. First article inspection samples, All subsequent semitrailers 3.2 Materials. Materials shall be as specified herein and in referenced specifications, standards and drawings.

16、Materials shall be free of all defects and imperfections that might affect the serviceability and appearance of the finished product (see 4.8.1). 3.2.1 Recycled, virgin and reclaimed materials. There are no requirements for the exclusive use of virgin materials. The use of recycled or reclaimed (rec

17、overed) materials is acceptable provided that all other requirements of this specification are met (see 6.4.1). 3.3 Design and construction. Completed vehicles shall conform to this specification and the applicable drawing listed below (see 4.8.1 and 4.8.2). Model Drawing number M172A1 8736073 M270A

18、1 8358925 3.3.1 Qualified products list (QPL). The contractor shall be responsible for using parts and assemblies necessary in vehicle construction that are listed as qualified products on the QPL and those approved for inclusion on the QPL. The contractors manufacturing inspection records shall spe

19、cifically list all QPL items by part or drawing number(s), name of supplier(s), and number and date of the QPL. When assemblies and parts are approved as qualified products, but not yet listed on the QPL, the contractor shall list the products by number and date of the approved document with the nam

20、e of suppliers(s) (see 4.1.4 and 4.8.1). 3.3.2 Ozone resistance. When rubber components are required to be ozone resistant, the degree of resistance shall be as specified in applicable specifications or drawings (see 4.8.1). 3 Provided by IHSNot for ResaleNo reproduction or networking permitted with

21、out license from IHS-,-,-MIL-S-45352F 23 - 99Ob 0396884 b W _. MIL-S-45352F 3.3.3 Seals. When the semitrailer is fording or operating in mud, sand or snow, the bearing seals shall prevent entrance of foreign matter into the bearings which are exposed to contamination during these operations. contami

22、nation of wheel bearing lubricant, after fording operations, shall be not greater than 2 percent (%). All bearing seals shall restrict the leakage of lubricants from bearings (see 4.8.2). Water 3.3.4 Electrical. 3.3.4.1 Electrical circuits. Electrical circuits shall maintain continuity from end to e

23、nd, without evidence of internal or external shorts, during all semitrailer operating conditions. All electrical cables and wiring shall be anchored in such a manner to preclude any damage to cables and wiring during all semitrailer operating conditions (see 4.8.2). 3.3.4.2 Lights. All lights specif

24、ied on applicable drawings shall operate throughout all semitrailer operating conditions (see 4.8.2). 3.3.5 Controls. All electrical, mechanical, and hydraulic controls shall operate without malfunction, throughout all ranges of operation, under all semitrailer operating conditions (see 4.8.2). 3.3.

25、6 Adjustment mechanisms. All adjustment mechanisms shall function properly, and maintain adjustment settings during all semitrailer operating conditions (see 4.8.2). 3.3.7 Welding. Welding shall meet the requirements specified on the applicable drawing (see 4.8.1 and 4.8.2). 3.3.7.1 Welding repairs.

26、 Welding repairs of any kind shall be made only when, and to the extent, specifically authorized by the acquisition activity (see 4.8.1 and 6.2). 3.3.8 Tie down devices. Unless otherwise specified (see 6.2), semitrailers shall be provided with tie down devices, of sufficient number and structural st

27、rength as to be adequate for transport by rail, sea and air (see 4.8.2). 3.3-9 Air and hydraulic lines, and fittings. Provisions shall be made to assure internal cleanliness of air and hydraulic lines and fittings, prior to initial use of semitrailer. All lines and connections shall be free of leaks

28、 and shall be anchored in such manner as to preclude damage during all semitrailer operating conditions (see 4.8.2). 3.3.10 Tires. The semitrailer shall be furnished with tube type tires conforming to class HW, style A of MIL-T-12459 (see 4.8.2). 33.11 Lifting attachments. The semitrailer shall be p

29、rovided with lifting attachments that are structurally adequate to lift the semitrailer. Lifting attachments shall be capable of lifting the Semitrailer when loaded with maximum payload, as specified below. shall conform to MIL-STD-209 (see 4.8.2 and 4.8.3). Lift slings, with spreader bar, 4 Provide

30、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-45352F 23 7777706 0176885 B W Semi - Vehicle trailer weight (lbs) M172A1 16,500 M270A1 17,500 MIL-S-45352F - Speeds (mph) 50,000 30 10 24,000 20 10 Payload (lbs) Highway Cross-country Model Maximum paylo

31、ad pounds (lbs) 3 M172A1 50,000 M270A1 24,000 3.3.12 Landing legs. Landing legs shall suppport the fully loaded semitrailer and withstand, without damage, the strains imposed when coupling and uncoupling the semitrailer from the towing vehicle and raising and lowering the loaded semitrailer. The lan

32、ding gear shall operate freely when vehicle is loaded or unloaded and shall operate without interference (see 4.8.2 and 4.8.4). . 3.4 Performance. The semitrailer shall meet the performance requirements of 3.4.1 through 3.4.8 of this specification when equipped as specified herein and as depicted on

33、 the drawings, serviced as specified in the applicable lubrication drawing, loaded as specified in table I and coupled to the towing vehicle. The semitrailer, serviced and equipped for existing climatic conditions, shall operate as specified without special equipment (see .4.8.5). TABLE I. Maximum w

34、eights, loads and speeds. 3.4.1.2 Cross-country operation. The semitrailer, loaded with rated payload uniformly distributed over the load area, shall be towed over unimproved roads, open fields, rolling hills and cross-country terrain at the sustained speed specified in table .I without damage to th

35、e semitrailer or towing vehicle. of gravity is established (see 4.8.5.2). The payload shall be distributed so that the proper center 3.4.2 Grade and slope operation. When towed over a dry, hard-surface free of loose material, the semitrailer shall meet the requirements of 3.4.2.1 and 3.4.2.2. 5 Prov

36、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-45352F 3.4.2.1 Longitudinal inclines. The semitrailer shall follow the towing vehicle without weaving to an extent affecting the controllability of the vehicle combination, when ascending and descendi

37、ng longitudinal inclines having a 20% grade (see 4.8.5.3). 3.4.2.2 Side slopes. The semitrailer shall follow the towing vehicle without slipping or upsetting, when operating on left and right side slopes having a 20% grade (see 4.8.5.4). 3.4.3 Braking. 3.4.3.1 Service brakes. The service brakes of t

38、he semitrailer and towing vehicle shall decelerate and stop the vehicle combination, with rated payload, on dry, smooth, level, hard-surfaced roads, free of loose materials, as follows (see 4.8.2 and 4.8.5.5): - a. M172A1 - The stopping distance shall be not more than 40 feet (ft) from a speed of 20

39、 miles per hour (mph). b. M270A1 - The stopping distance shall be not more than 50 ft from a speed of 20 mph. 3.4.3.2 Automatic brake actuator. The actuator shall automatically apply the semitrailer service brakes upon breakaway from towing vehicle. actuator shall maintain the application of brakes

40、holding the trailer stationary on a 30% grade under all loads specified herein for not less than 15 minutes (see 4.8.2 and 4.8.5.6). The 3.4.4 Turning ability. The semitrailer-towing vehicle combination shall be capable of making complete turns to the right or left, with the semitrailer assuming a 9

41、0 degree angle without cramping, side-slipping or damage to either the towing vehicle or the semitrailer (see 4.8.5.7). 3.4.5 Fording ability. The semitrailer shall be capable of being towed in fresh or salt water to a depth of not less than 5 ft for periods up to 15 minutes, without impairing perfo

42、rmance of the semitrailer or its components. Fording shall be accomplished without use of special kits, and with a minimum of preparation or servicing before and after the fording operation (see 4.8.5.8 and 6.5). 3.4.6 Environmental. The semitrailer shall be capable of being towed under extreme cond

43、itions of weather and altitude in ambient temperatures ranging from minus 65 degrees Fahrenheit (OF) to plus 125F. The semitrailer shall be capable of withstanding storage at minus 80F without deterioration that cause failure of any component (see 4.8.5.9). 3.4.7 Reliability. The semitrailer shall a

44、chieve not less than 6000 mean miles between failure (MMBF) when operated in accordance with the 6000-mile test scenerio specified in 4.3.2.2 (see 4.8.5.10). 6 , Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-45352F 23 M 9999906 0396887 3 M MI

45、L-S-45352F 3.4.7.1 Failure. A failure is any malfunction of an end item requiring overhaul, replacement, rebuild, salvage or other corrective action as prescribed by the maintenance manual, which cannot be deferred for the remainder of 6000 miles. 3.4.7.2 Corrective action. Corrective action is not

46、deferrable if malfunction causes, or would cause if not corrected: r“ a. Inability to commence operation or cessation of operation. b. c Critical or catastrophic hazard as defined in MIL-STD-882. Inability to conform to the requirements of the specification- z. 3.4.7.3 Malfuntion. Any malfunction wh

47、ich the operator or crew can remedy will not be considered a failure provided that repair is authorized or prescribed, as an operator function, and can be accomplished within 1 hour using only controls, tools, or spare parts incorporated in, or carried with, the end item, or its towing vehicle. 3.4.

48、8 Maintainabilty. Total scheduled maintenance excluding driver and crew checks and services shall not exceed 8 manhours during the first 6000 miles of operation in accordance with the test scenerio specified in 4.3.2.2. This equates to a maintenance ratio (MR) of 0.027 at 20 operational miles equiva

49、lent to 1 operational hour. The scheduled maintenance interval shall be 6 months or 6000 miles, whichever comes first (see 4.8.5.11). 3.5 Painting. Unless otherwise specified (see 6.2), the exterior and interior of the semitrailer, component assemblies and parts which require painting shall be cleaned, treated and CARC painted in accordance with MIL-STD-193 and Drawing 12355846 (see 4.8.2). 3.5.1 Protective coating. When specified (see 6.2), all parts of s