ARMY A-A-52029-1991 CONTAINER CARGO SIDE OPENING《单开放单开货物集装箱》.pdf

《ARMY A-A-52029-1991 CONTAINER CARGO SIDE OPENING《单开放单开货物集装箱》.pdf》由会员分享，可在线阅读，更多相关《ARMY A-A-52029-1991 CONTAINER CARGO SIDE OPENING《单开放单开货物集装箱》.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、i A-A-52029 83 9999974 0063460 3 m - I INCH-POUND 1 9 May 1991 A-A-52029 COMMERCIAL ITEM DESCRIPTION CONTAINER, CARGO, . SIDE OPENING The General Services Administration has authorized the use of this commercial item description. This item description covers 20 foot, reusable, IS0 lCC, side opening,

2、 cargo containers for the transportation, distribution, and storage of military supplies. Salient characteristics Description. The containers shall be noncollapsible, of a permanent character and suitable for repeated use. inch IS0 1CC container with full length side opening doors. shall comply with

3、 the requirements of IS0 1496/1. The container shall be a steel 8 foot 6 The container Weiqht, ratinqs and dimensions. The tare weight of the container shall be the minimum practical but shall not exceed 6100 pounds. The gross weight rating shall be 52,910 pounds. Dimensions, tolerances, and diagona

4、l differences of the container shall meet the requirements for a 20 foot nominal length containers as specified in IS0 668. Standard Droduct. Except as otherwise specified herein, the container shall The container shall be new and be the standard product of the contractor. unused. Material. Material

5、 shall be as specified herein. Used, rebuilt or remanufactured components, pieces, and parts shall not be incorporated into the container. Materials not specified shall be in accordance with Federal, Military, or National Technical Society, Association or Institute specifications or standards. fabri

6、cated from compatible materials, inherently corrosion resistant or treated to provide protection against the various forms of corrosion and deterioration that may be encountered in any of the applicable operating or storage environments to which the container may be exposed. Material deterioration,

7、prevention and control. The container shall be Beneficial comments, recommendations, additions, deletions, clarifications, etc, and other data which may improve this document should be sent by letter to: Commander, US Army Belvoir Research, Development and Engineering Center, ATTN: STRBE-TSE, Fort B

8、el voi r, VA 22060-5606. AMSC N/A FSC 8115 DISTRIBUTION STATEMENT A. Approved for public release, distribution is unlimited. A Licensed by Information Handling ServicesProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52029 81 9999974 00bL4b1 5 A-A

9、-52 02 9 Dissimilar metals. Dissimilar metals shall not be uced in inthte contact with each other unless protected against galvanic corrosion. specific material, material finish or treatmsnt for use with component or Cubcomponent, and shall make information available upon request to the contracting

10、officer or designated representative. recesses and voids in which contraband can be concealed or where moisture can accumulate. beyond the outside surfaces of the comer fittings. Identification of materials and finishes. .The contractor shall identify the Construction. The containers shall be constr

11、ucteii so as to be free of any No part of the container (when empty) shall protrude Doors. An unobstructed door opening with minimum dimensions of 84 inches high and 221 inches wide shall be provided. shall be hung within the side of the container to pravide access to the interior of the container.

12、The doors shall be hinged together to make two pairs. Heavy uty hhge pins, recessed within the corner post shall be provided on each door allowing the door pair to open a minimum of 170 degrees. corrosion resistant steel pins. than two heavy-duty, handle operated cam locking devices with anti-rack p

13、rovisions which through lever type action aid in releas- the door seal fram the door frame. accept- a padlock and security seal. doors in the full open position and shall be of a material which will not scrape or chafe the container when the doors are closed. The doors, when closed, shall be sealed

14、in such a manner as to prevent moisture entry into the container. hinges shall be permanently lubricated. The steel side walls and end walls may be of the interior or exterior post type, corrugated or of smooth skin construction. The end walls and side walls shall withstand loading in accordance wit

15、h IS0 1496/1 except each end wall shall withstand an internal loadkg equal to the full payload uniformiy distributed over the surface of the end wall. Four equally sized doors Each pair shall be hinged to a comer post. Steel hirges shall have Each door shall be provided with not less Fach locking de

16、vice handle must be capable of Means shall be provided to hold the All movixj parts of the door locking mechanism and door Side walls and enCi walls. Floor. The floor shall be fabricated of marhe grade harawood. The floor shall be attacheci to the crossmembers by countersunk fasteners, 1/4 inch mini

17、mum head diameter, either of the self-tapping screw type, or machine screws with self-locking nuts and shall be installed so that each head is O to 1/16 inch below the board surface and at least 1 inch frm the board edge. Screws shall be used on 10 inch centers on each cross member. The floor shall

18、be installed to permit lateral variations in floor board width due to swelling. be chdcally treated in accordance with the regulations as stated by the Vommonwealth of Australia Department of Health.Il affixed to the container indicating the immunization code used in the treat- proceCs. The floor sh

19、all be watertight. All wood camponents shall A data plate shall be Underctructure. All crossmembers shall be of the same configuration and strength and shall have a maximum center to center distance of 12 inches. After painting of the metal surfaces, the entire underside of the container floor, incl

20、uding croscmemberc, corner fittkgs, side rails, and end frame 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52029 81 m 9999974 00b14b2 7 m A-A-52 02 9 memberc shall be coated with a bituminous undercoat applied to a minhum dry film thickness

21、of 6 mils (150 microns). 1) Forklift pcckets. Forklift pockets for handling loaded and unloaded containers shall be fumishd. reqUirementC of Is0 1496/1. the follcwing warning shall be stenciled in minimum 3 inch white letters: “EMPrm LJxT ONLYI . Forklift pockets shall confonn to the Above the hide

22、pockets (unloaded pockets) Roof. The roof shall be self draining. Corrugated roofing construction is permitted. If roof bows are provided and are fastened to the roof sheet, they shall be bonded by a suitable bonding agent. fastend to the roof sheet, anti-chafing material shall be affixed to the roo

23、f bows on the curfaces facing the roof sheets. rails, and top end frame members shall be a himum 1/4 inch below the top surface of the corner fittings. The roof sheet shall be not less than 1/4 inch thickness within 12 inches from the top rail at each end of the container. the door side of the conta

24、iner. If the roof bows are not The roof sheet, top side A rain gutter shall be provided to divert moisture away from corner fitths. Corner fittings shall conform to the r one ring in each corner of the side rail and six evenly spa nunter, and date of this item description. wnerls cade and serial nrm

25、iber for each container. When this commercial item description is used for prccuremnt, the I commercial item certification clause must appear in the solicitation. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52029 1 W 9999974 00bL465 2 A-A-5

26、2 02 9 Dqarhent of Trancportation (DCIII), Code of Federal Regulations, 450 and 451 and D3T, Wireau of Ekplosives, EDE-6000, part 172, appendix C are available from the superintendent of Dx-ummts, Government printing Office, Washington, IS0 1496/1, IS0 1161, IS0 668, IC0 6346 are available fran the

27、American National Standardc Institute, 1430 Broadway, New York, NY 10018. 20202. SSPC-10 is available from the Steel Structures Painting Council, 4400 Fifty Avenue, Pittsburgh, PA 15213-2683. The contracting officer should require that three camplete sets of approved blueprhts/design drawings as sta

28、mped by the approval agency and shall accompany all proposals submitted. subject to satisfactory prototype test is acceptable. The contract- officer should require that three caplete sets of fully approved design drawhqs as stamped by the approval authority must be submitted prior to the start of pr

29、oduction. officer in addition to the approval authority. The contracting officer should require that three camplete sets of specifications accompany all proposals submitted; and three ccnnplete sets of specifications, fully approved, be submitted prior to the start of production. Recommend all chang

30、es must be approved by the contracting officer. The contracting officer should require three copies of the container finish- and surface protection treatment offered accampany proposals submitted. The foiimiq are suggested sources of supply (campetition is not limited to these sources) : Container C

31、onCeptc Inc., 7501 Lemont Road, Suite 230, Woodridge, IL 60517. Containertechik Hamburg GmbH & campany, Heilwigstrasse 107, 2000 Hamburg 20, Ehergo Invest R.O. Vaso Miskin Crni, Damovalaca Kwi br4, 71000 Sarajevo, Ganz Danubius Trading Co Ltd., FOB 118, H-1325 Budapect, Hungary. (1) 149370. Graaff G

32、mbH, P.O. Box 160 + 180, Heinrich-Nagel-Strasse 1, D3210, Elze (Hanover), Federal Republic of Germany. Telephone: (O) 5068-18-281. HIM Containers Lkd, Old Post Office, Calcutta 700 O01 India. Telephone: (33) 28-7856. Ming Myung Industrial Campany Ltd., 115 Samgak-Ibng, ChooKj-la, 4-5 Floor, Kyunggi

33、Bldg, Seoul, Republic of Korea. Telephone: (2) 733-5931. Inta-Eimar Holding, Contespan-Ehar SA, Poligono Inductrial de Malpica, Calle H No 12, 50016, Zaragoza, Spain. Telephone: (76) 574662. RaUtaruukki Oy, Oulu Works, P.O. Box 217, 90101, Oulu, Finland. Sim SpA, Via Casassa, Regione Oltre Tanaro, 1

34、262 Cherasco (CN), Italy. Swedecon Mekaniska AB, Box 5044, S-831 05 OsterSund, Sweden. Telephone: A stamp of approval by the approval agency which is Recarmnend all changes be approved by the contracting Telephone: (708) 985-5850. Federal Republic of Germany. Telephone: (40) 46 10 69. Yugoslavia, Te

35、lephone: (71) 526 322. Telephone: Telephone: (81) 382-453. Telephone: (172) 48215. (63) 11 76 30 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Tiphook Modular Systems, Station Road, Reddish, Stockport, Cheshire SK5 6W, Tbkyu Car Corporation, Cont

36、ainer Sales Department, Yaesu-fitsui Bldg, 7-2, 2- Trans Freight Containers La., 72-73 Narhmn Bhavan, Nau mint, Barnbay 400 The preparing activity for this item description is the US Anny Belvoir Research, Development, and Engheerh Center, ATIN: 5606. Ehglard. Telephone: (061) 432 0211 chme Yaw, Chuo-ku, Tbyko 104, Japan. Telephone: (3) 272-7061. 021, India. Telephone: 202 2172 an 202 4116. 6 STRBE-TSE, Ft. Belvoir, VA 22060- custodian: Anny-m Preparing activity: amiy-ME Project 8115-0523 : 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-