ANSI American Society of Sanitary Engineering 1064-2006 Performance Requirements for Backflow Prevention Assembly Field Test Kits.pdf

《ANSI American Society of Sanitary Engineering 1064-2006 Performance Requirements for Backflow Prevention Assembly Field Test Kits.pdf》由会员分享，可在线阅读，更多相关《ANSI American Society of Sanitary Engineering 1064-2006 Performance Requirements for Backflow Prevention Assembly Field Test Kits.pdf（28页珍藏版）》请在麦多课文档分享上搜索。

1、Backflow Prevention Assembly Field Test Kits 1ASSE 1064-2006(R2011)Performance Requirements forBackflow Prevention Assembly Field Test KitsAmerican Society of Sanitary EngineeringASSE Standard #1064-2006(R2011)ASSE Board Approved: August, 2011 ANSI Approved: August, 2011An American National Standard

2、Backflow Prevention Assembly Field Test Kits iASSE 1064-2006(R2011)General InformationNeither this standard, nor any portion thereof, may be reproduced without the written consent of the American Society of Sanitary Engineering.Instructions for receiving authorization to display the ASSE Seal are av

3、ailable from ASSEs International Office. Organizations wishing to adopt or list any ASSE Standard should print the ASSE Standard number on the cover page first and in equal or larger type to that of the adopting or listing organization.American Society of Sanitary EngineeringWestlake, OhioCopyright

4、2011, 2006, 2001All rights reserved.ii Backflow Prevention Assembly Field Test KitsASSE 1064-2006(R2011)Backflow Prevention Assembly Field Test Kits iiiASSE 1064-2006(R2011)ForewordThis foreword shall not be considered a part of the standard. However, it is offered to provide background information.

5、ASSE Product Standards are developed in the interest of consumer safety.The American Society of Sanitary Engineering is dedicated to the preservation of public health and safety through its guiding principle, “Prevention Rather Than Cure.”The ASSEs Product Standards Program systematically evaluates

6、new technologies through formal requests and addresses the development and promulgation of performance standards designed to safeguard public health and safety.Standards for the performance of plumbing system components are considered by the American Society of Sanitary Engineering to be of great va

7、lue in the development of improved plumbing systems for the increased protection of public health and safety.Backflow test kits are used to annually test products conforming to the following ASSE Standards: ASSE Standard #1013, Performance Requirements for Reduced Pressure Principle Backflow Prevent

8、ers and Reduced Pressure Principle Fire Protection Backflow Preventers ASSE Standard #1015, Performance Requirements for Double Check Backflow Prevention Assemblies and Double Check Fire Protection Backflow Prevention Assemblies ASSE Standard #1020, Performance Requirements for Pressure Vacuum Break

9、er Assembly ASSE Standard #1047, Performance Requirements for Reduced Pressure Detector Fire Protection Backflow Prevention Assemblies ASSE Standard #1048, Performance Requirements for Double Check Detector Fire Protection Backflow Prevention AssembliesThe following standard provides requirements fo

10、r backflow test kits so that a degree of accuracy shall be obtained while the technician certifies the operation and performance of backflow assemblies.The accuracy test applies to gauge-displayed value when compared to the accepted standard value or true value. The degree of conformity is expressed

11、 in terms of maximum deviation from the true value. The accuracy rating includes the combined effects of linearity and repeat-ability. Effects of varying operating conditions, such as EMI/FRI exposure, ambient temperature, process static pressure or temperature which may cause the instruments displa

12、yed value iv Backflow Prevention Assembly Field Test KitsASSE 1064-2006(R2011)to exceed accuracy, must be determined by test. The results, with established limitations of the useful operating range (where the instrument does not exceed accuracy rating), must be included in documentation, instruction

13、 manuals and test certificates.These requirements apply to the complete test kit and its assembly, regardless of technology employed to measure and display the pressure of differential pressure. The kit must be provided with documentation certifying that the instrument conforms to the accuracy requi

14、rements of this standard and has been calibrated with devices traceable to NIST. The calibration test devices shall have an accuracy rating, which is at least four (4) times greater than the accuracy of the test kit instruments.Recognizing the application specific requirements, it is recommended tha

15、t the calibration tests be conducted with the kit in the upright/vertical position. Data should be taken in response to the decreasing pressure, at a minimum of five (5) points.Recognition is made of the time volunteered by the members of the working group and of the support of the manufacturers who

16、 participated in meetings for this standard.This standard does not imply ASSEs endorsement of a product which conforms to these requirements.Compliance with this standard does not imply acceptance by any code body.Backflow Prevention Assembly Field Test Kits vASSE 1064-2006(R2011)Joseph FugeloProduc

17、t Standards Committee ChairmanLabov Co.Philadelphia, Pennsylvania Rand AckroydRand Technical Consulting, LLCNewburyport, Massachusetts William Briggs Jr.MGJ AssociatesNew York, New YorkMaribel CamposICC Evaluation ServicesWhittier, CaliforniaJudson CollinsJulyco ProfessionalsMannford, OklahomaRon Ge

18、orgePlumb-Tech Design on a corrosion resistant plate securely attached to the BFTK with a corrosion resistant material; on a decal that is alcohol wipe resistant/weather resistant securely attached to the BFTK; or printed on the dial plate. 4.3 Field TestingRecommended field testing instructions con

19、forming to ASSE/ANSI Standard Series 5000 shall be furnished by the manufacturer.4.4 Manufacturers InstructionsManufacturers instructions shall include information on periodic calibration.12 Backflow Prevention Assembly Field Test KitsASSE 1064-2006(R2011)Section V5.0 DefinitionsDefinitions in this

20、standard shall take precedence over any other publication. Definitions not shown are found in the Plumbing Dictionary, Sixth Edition, published by ASSE.Backflow Prevention Assembly Field Test Kits 13ASSE 1064-2006(R2011)Appendix AA1.0 Annual Calibration Verification of BackflowField Test KitsThis ap

21、pendix shall not be considered a part of the standard.A1.1 PurposeTo protect potable water supply by testing backflow prevention assemblies with BFTKs with accuracy which conforms to this standard.A1.2 Test FrequencyIt is recommended that BFTKs have their accuracy checked and documented a minimum of

22、 every twelve (12) months.A1.3 Procedure 1. Drain all water, if necessary, from the BFTK.2. Follow Section 3.2, Accuracy Test, of this standard.3. Calibration should be adjusted only if BFTK readings fall outside of the accuracy tolerances of this standard. If calibration adjustment or repair is req

23、uired, contact the BFTK supplier for instructions on how to proceed.4. A signed and dated calibration certificate, identifying make, model, serial number and accuracy tolerance, should be obtained and saved. It is common practice to save calibration records for seven (7) years.5. A dated calibration

24、 decal should be applied to the BFTK in a visible location which will not hinder BFTK tags or indications.American Society of Sanitary EngineeringFOR PLUMBING AND SANITARY RESEARCH 901 Canterbury Road, Suite A Westlake, Ohio 44145Phone (440) 835-3040 Fax (440) 835-3488E-Mail general.infoasse-plumbing.org Web: www.asse-plumbing.orgPreventionRatherThanCure