AIR FORCE MIL-DTL-0083406 D-2010 ANTI-G GARMENT CUTAWAY CSU-13B P《CSU-13B P型脱离式抗重力服》.pdf

《AIR FORCE MIL-DTL-0083406 D-2010 ANTI-G GARMENT CUTAWAY CSU-13B P《CSU-13B P型脱离式抗重力服》.pdf》由会员分享，可在线阅读，更多相关《AIR FORCE MIL-DTL-0083406 D-2010 ANTI-G GARMENT CUTAWAY CSU-13B P《CSU-13B P型脱离式抗重力服》.pdf（63页珍藏版）》请在麦多课文档分享上搜索。

1、 INCH POUND MIL-DTL-0083406D(USAF) 15 April 2010 USED IN LIEU OF MIL-DTL-83406C 24 March 2006 DETAIL SPECIFICATION ANTI-G GARMENT, CUTAWAY, CSU-13B/P Reactivated after 24 March 2006 and may be used for new and existing designs and acquisitions. This specification is for an Aviation Critical Safety I

2、tem (CSI/Flight Safety Critical Aircraft Part (FSCAP) and the acquisition process must comply with the DoD Materiel Management Regulation DoD 4140.1-R Comments, suggestions, or questions on this document should be addressed to ASC/ENRS, 2530 Loop Road West, Bldg 560, Wright-Patterson AFB OH 45433-71

3、01 or e-mailed to Engineering.Standardswpafb.af.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at https:/assist.daps.dla.mil. AMSC N/A FSC 8475 DISTRIBUTION STATEMENT A. Approved for public release; distribu

4、tion is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-0083406D(USAF) 2 This specification is approved for interim use by the Air Force. Other activities in the Department of Defense may use this interim revision or may continue u

5、sing MIL-DTL-83406C. 1. SCOPE 1.1 Scope. This specification covers the requirements for the CSU-13B/P anti-g garment, which is designated as a critical safety item. 1.2 CLASSIFICATION. Anti-g garments are of the following sizes and lengths, as specified (see 6.2 and 6.6): Small regular (SR) Medium r

6、egular (MR) Large regular (LR) Large extra long (LXL) Small long (SL) Medium long (ML) Large long (LL) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3, 4, and 5 of this specification. This section does not include documents cited in other section

7、s of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3, 4, and 5 of this specification, wh

8、ether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the

9、 solicitation or contract. FEDERAL STANDARDS FED-STD-4 Glossary of Fabric Imperfections FED-STD-595/27040 Miscellaneous, Semigloss FED-STD-595/34096 Green, Flat or Lusterless FED-STD-595/34097 Green, Flat or Lusterless FED-STD-595/34128 Green, Flat or Lusterless FED-STD-595/37038 Miscellaneous, Flat

10、 or Lusterless FED-STD-595/37056 Miscellaneous, Flat or Lusterless Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-0083406D(USAF) 3 COMMERCIAL ITEM DESCRIPTIONS A-A-50195 Thread, Aramid A-A-55126 Fastener Tapes, Hook and Loop, Synthetic A-A-5

11、5621 Fasteners, Snap, Style 3 Pronged Ring Head Type (16 Ligne) A-A-55634 Zippers (Fasteners, Slide Interlocking) A-A-55809 Insulation Tape, Electrical, 600V, Polyvinyl Chloride, Pressure-Sensitive Adhesive A-A-59826 Thread, Nylon DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-5038 Tape, Textile and W

12、ebbing, Textile, Reinforcing, Nylon MIL-W-5664 Webbing, Textile, Elastic MIL-PRF-6855/4 Rubber, Synthetic, Tubing MIL-DTL-32075 Label: for Clothing, Equipage, and Tentage, (General Use) MIL-DTL-32092 Leather, Cattlehide, Deerskin and Horsehide, Chrome Tanned MIL-T-38328 Tape, Textile, Nylon, Aromati

13、c, Nonmelting, Reinforcing MIL-C-43204 Cloth, Spacer (Olefin) MIL-L-43283 Leather, Calfskin, Kip, and Cattlehide for Footwear Uppers, Chrome Tanned MIL-W-81116 Webbing, Textile, Polyamide, High Temperature Resistant, Loop MIL-C-83242 Cord, Aromatic Polyamide, Nonmelting MIL-C-83390 Connector, Hose,

14、Quick-Acting, Male, Anti-G Garment MIL-C-83429 Cloth, Plain and Basket Weave, Aramid MIL-C-83489 Cloth, Coated, Nylon, Polyurethane Coated DEPARTMENT OF DEFENSE STANDARDS MS 27755 Connector, Hose Quick Disconnect, Female, Anti “G” Suit (Copies of these documents are available online at https:/assist

15、.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this document t

16、o the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-0083406D(USAF) 4 AIR FORCE DRAWINGS 71380 Patterns, CSU-

17、13B/P anti-g garment, Size Small Regular 71381 Patterns, CSU-13B/P anti-g garment, Size Small Long 71382 Patterns, CSU-13B/P anti-g garment, Size Medium Regular 71383 Patterns, CSU-13B/P anti-g garment, Size Medium Long 71384 Patterns, CSU-13B/P anti-g garment, Size Large Regular 71385 Patterns, CSU

18、-13B/P anti-g garment, Size Large Long 71386 Patterns, CSU-13B/P anti-g garment, Miscellaneous All Sizes 74204 Spacer, Tube Anti-g Garment 74206 Pattern, Anti-g Garment, CSU-13B/P, Size Large Extra Long 200518653 Source Control Drawing- Fastener, Slide (Copies of these documents are available from t

19、he Defense Supply Center Philadelphia, Clothing and Textiles Directorate, ATTN: DSCP-CBTC, (Bldg 6), 700 Robbins Ave., Philadelphia, PA. 19111-5092 or for DoD personnel they are available online at .) 2.3 Non-Government publications. The following documents form a part of this document to the extent

20、 specified herein. Unless otherwise specified, the issues of documents are those cited in the solicitation or contract. AEROSPACE INDUSTRIES ASSOCIATION (AIA) NATIONAL AEROSPACE STANDARDS (NAS) NAS397 Clamp Ratchet, One Piece (DoD Adopted) NASM20230 Grommet, Metallic, Plain and Rolled Rim, with Wash

21、er, Type I and Type III (DoD Adopted) NASM27980 Fasteners, Snap, Style 2 (Regular Wire Spring Clamp Type) (DoD Adopted) NASM27983 Fasteners, Snap, Style 4 (Three Way Locking Type) (DoD Adopted) (Copies of these documents are available from www.aia-aerospace.org or Aerospace Industries Association, 1

22、000 Wilson Blvd, Suite 1700, Arlington VA 22209-3901.) AMERICAN SOCIETY FOR QUALITY (ASQ) ANSI/ASQ Z1.4 Sampling Procedures and Tables for Inspection by Attributes (DoD Adopted) (Copies of this document are available from www.asq.org or the American Society for Quality, 600 North Plankinton Ave., Mi

23、lwaukee WI 53203-2914.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-0083406D(USAF) 5 ASTM INTERNATIONAL A 313/A 313M Standard Specification for Stainless Steel Spring Wire (DoD Adopted) D 5034 Standard Test Method for Breaking Strength an

24、d Elongation of Textile Fabrics (Grab Test) D 6193 Standard Practice for Stitches and Seams (DoD Adopted) (Copies of these documents are available from www.astm.org or ASTM International, 100 BarR Harbor Dr., West Conshohocken PA 19428-2959.) THE PARACHUTE INDUSTRY ASSOCIATION (PIA) PIA-C-3953 Cloth

25、, Duck, Nylon (DoD Adopted) PIA-W-4088 Webbing, Textile, Woven Nylon (DoD Adopted) (Copies of these documents are available from or the Parachute Industry Association, 3833 West Oakton St., Skokie IL 60076.) SAE INTERNATIONAL SAE AMS-T-22085 Tapes, Pressure-Sensitive, Adhesive, Preservation and Sea

26、ling (DoD Adopted) (Copies of this document are available from or www.sae.org or SAE World Headquarters, 400 Commonwealth Dr., Warrendale PA 15096-0001.) AMERICAN ASSOCIATION OF TEXTILE CHEMISTIS AND COLORISTS (AATCC) Test Method 135 Dimensional Changes of Fabrics after Home Laundering (Copies of th

27、is document are available from or www.aatcc.org or AATCC, P.O. Box 12215 Research Triangle Park, NC 27709-2215) 2.4 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document,

28、 however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Qualification. The anti-g garments furnished under this specification shall be products that are authorized by the qualifying activity for listing in the Qualified Products Databas

29、e (QPD) before contract award (see 4.3 and 6.3). 3.2 First article. When specified (see 6.2), a sample shall be subjected to first article inspection in accordance with 4.4. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-0083406D(USAF) 6 3.3

30、 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible, provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous

31、life cycle costs. However, used, rebuilt, or refurbished items shall not be provided. 3.4 Materials and parts. Except for the metallic materials and parts, the materials and parts of the anti-g garment shall have been manufactured not more than 12 months prior to the date of delivery of the anti-g g

32、arment. 3.4.1 Basic materials 3.4.1.1 High temperature resistant cloth. Except for the bladder, the basic material for the anti-g garment shall be plain weave conforming to type II, class 6 of MIL-C-83429 and the color shall be AF Sage Green 1590 (see 6.4) with the exception that the weight of the t

33、est material shall be 4.6 5.0 ounces per yard square and AATCC Test Method 135 shall be used, utilizing 5 wash cycles. 3.4.1.2 Polyurethane coated nylon cloth. The material for the bladder, including the attachment patches, reinforcement of inflation tubes, external covering, and checklist retainer

34、area of thigh, shall be plain weave conforming to type I of MIL-C-83489,with the exception that finished fabric weight shall be 5.5 - 6.75 ounces per square yard and minimum tear strength shall be 5 lbs warp and 4 lbs fill. 3.4.2 Reinforcements and bindings. Unless otherwise specified herein, the re

35、inforcements shall be made of the basic material specified in 3.4.1.1. The 5/16-inch wide (finished), centerfold, bias binding shall be 45 degrees bias, cut 1-1/4 inches to 1-3/8 inches wide from the basic material (see 3.4.1.1). 3.4.3 Adjustment laces and lanyard. The cord for the lanyard and for t

36、he adjustment laces shall be coreless conforming to type I of MIL-C-83242 and shall approximately match the shade of the basic material (see 3.4.1.1). 3.4.4 Slide fasteners. The slide fasteners shall conform to table I of this specification and AF Drawing 200518653, except as otherwise specified her

37、ein. The slide fasteners shall be brass with a tab pull. The tape and the bead of all size fasteners (including the body opening) shall be a high temperature resistant polyamide material that has been dyed to match the color of the basic material specified in 3.4.1.1. The tape of the slide fastener

38、shall have colorfastness in accordance with A-A-55634, except that fair colorfastness, in lieu of good colorfastness, to light will be acceptable. The finish of the chain and the other metal components shall be black chemical finish. All automatic locking sliders shall have a pin-type locking device

39、. 3.4.5 Spacer material. The spacer material for the bladder and bladder inflation tube shall conform to type III of MIL-C-43204. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-0083406D(USAF) 7 TABLE I. Slide fasteners. GARMENT SIZE CONTROL

40、DRAWING LOCATION SR 200518653-01 Thigh take-up SL/ML/LL/LXL 200518653-03 Thigh take-up MR/LR 200518653-05 Thigh take-up ALL 200518653-07 Pocket ALL 200518653-11 Body SR 200518653-13 Left leg SR 200518653-15 Right leg SL 200518653-17 Left leg SL 200518653-21 Right leg MR 200518653-23 Left leg MR 2005

41、18653-25 Right leg ML 200518653-27 Left leg ML 200518653-31 Right leg LR 200518653-33 Left leg LR 200518653-35 Right leg LL 200518653-37 Left leg LL 200518653-41 Right leg LXL 200518653-43 Left leg LXL 200518653-45 Right leg 3.4.6 Stiffeners. The stiffeners for the slide fasteners, front and back bo

42、dy, shall be made of nylon cloth conforming to class 2 of PIA-C-3953. 3.4.7 Aromatic polyamide tape. The slide fasteners tape for the pull thong, loops for the slide fasteners, and the hanger shall be 5/16 1/32 inch wide conforming to type VI of MIL-T-38328 and shall approximately match the color of

43、 the basic material (see 3.4.1.1). The webbing for the waist and leg socket snap tap assemblies shall be 1- 1/32 inch wide conforming to MIL-T-38328, type IV. 3.4.8 Nylon webbing. The webbing for the knife pocket reinforcement shall be untreated, conforming to class 1, type XII of PIA-W-4088, and ma

44、tch the shade of the basic material in 3.4.1.1 or it shall be natural. The webbing of stiffeners shall conform to type I of PIA-W-4088. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-0083406D(USAF) 8 3.4.9 Wrapping tape for anti-g garment ho

45、se assembly. The tape for wrapping the anti-g garment hose assembly shall be black, 1-inch wide and conform to A-A-55809. 3.4.10 Lacer loops. The tape for the lacer loops shall conform to MIL-W-81116, except that the sleeve may have 16 carriers, in lieu of 20 carriers; the length shall be 39-1/2 inc

46、hes, in lieu of 45 inches for each yard of webbing; and the color shall match the color of the basic material (see 3.4.1.1). 3.4.11 Thread. Unless otherwise specified herein, the thread for all sewing operations shall be soft, 800d, and 80 or 60 Tex, conforming to A-A-50195 and shall approximately m

47、atch the color of the basic material as specified in 3.4.1.1. (NOTE: This thread may be used to sew the nylon mesh cloth (see 3.4.21) in lieu of the thread conforming to type I, class A, Tex 68-70 of A-A-59826, which is specified on AF Drawing 74204.) 3.4.12 Snap fasteners. Except for the knife pock

48、et, the snap fasteners shall be black conforming to style 3, finish A of A-A-55621 (Part Identifying Nos. (PIN): A-A-55621-1B, pronged ring; A-A-55621-2B, socket; A-A-55621-4B, and A-A-55621-5B, eyelet). The snap fastener for the knife pocket shall conform to style 4, construction A of NASM27983 (PI

49、N Nos.: NASM27983-1, button; NASM27983-2 socket, NASM27983-3, stud; and NASM27983-4, eyelet). Snaps shall be securely attached to the materials. The roller barrels in each socket and stud shall be rolled over completely and shall have a symmetrical donut shaped appearance with no cracks. 3.4.13 Grommet. The grommet shall be size 00 conforming to NASM2023