BS ISO 9182-4-2013 Tools for pressing Guide pillars Type C pillars with taper lead and bush《冲压工具 导柱 C型带套的锥头导柱》.pdf

《BS ISO 9182-4-2013 Tools for pressing Guide pillars Type C pillars with taper lead and bush《冲压工具 导柱 C型带套的锥头导柱》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 9182-4-2013 Tools for pressing Guide pillars Type C pillars with taper lead and bush《冲压工具 导柱 C型带套的锥头导柱》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards Publication BS ISO 9182-4:2013 Tools for pressing Guide pillars Part 4: Type C, pillars with taper lead and bushBS ISO 9182-4:2013 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO 9182-4:2013. It supersedes BS 7568-28:1993 which is withdrawn. The

2、 UK participation in its preparation was entrusted to Technical Committee MTE/12, Tools for pressing and moulding. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contrac

3、t. Users are responsible for its correct application. The British Standards Institution 2013. Published by BSI Standards Limited 2013 ISBN 978 0 580 76977 1 ICS 25.060.10; 25.120.10 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published

4、under the authority of the Standards Policy and Strategy Committee on 31 December 2013. Amendments issued since publication Date T e x t a f f e c t e dBS ISO 9182-4:2013 ISO 2013 Tools for pressing Guide pillars Part 4: Type C, pillars with taper lead and bush Outillage de presse Colonnes de guidag

5、e Partie 4: Type C, colonnes emmanchement conique et sa bague de guidage INTERNATIONAL STANDARD ISO 9182-4 Second edition 2013-12-15 Reference number ISO 9182-4:2013(E)BS ISO 9182-4:2013ISO 9182-4:2013(E)ii ISO 2013 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2013 All rights reserved. Unles

6、s otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the ad

7、dress below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in SwitzerlandBS ISO 9182-4:2013ISO 9182-4:2013(E) ISO 2013 All rights reserved iii C

8、ontents Page Foreword iv 1 Scope . 1 2 Normative references 1 3 Dimensions . 1 4 Material 3 5 Designation 3 Bibliography 5BS ISO 9182-4:2013ISO 9182-4:2013(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies).

9、 The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-

10、governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are describ

11、ed in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to

12、the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the IS

13、O list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, a

14、s well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information The committee responsible for this document is ISO/TC 29, Small tools, Subcommittee SC 8, Tools for pressing and moulding. This second

15、 edition results from the reinstatement of ISO 9182-4:1992 which was withdrawn in 2007 and with which it is technically identical. ISO 9182 consists of the following parts, under the general title Tools for pressing Guide pillars: Part 1: Types Part 2: Type A, straight pillars Part 3: Type B, end-lo

16、cking pillars Part 4: Type C, pillars with taper lead and bush Part 5: Type D, end-locking pillars with flangeiv ISO 2013 All rights reservedBS ISO 9182-4:2013INTERNATIONAL ST ANDARD ISO 9182-4:2013(E) Tools for pressing Guide pillars Part 4: Type C, pillars with taper lead and bush 1 Scope This par

17、t of ISO 9182 specifies the dimensions and tolerances, in millimetres, of guide pillars, type C, with taper lead and bush, intended for use in press tools. It gives guidance on the materials and specifies the hardness and the designation of guide pillars which meet the requirements of this part of I

18、SO 9182. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including

19、any amendments) applies. ISO 6753-1:2005, Tools for pressing and moulding Machined plates Part 1: Machined plates for press tools 3 Dimensions The dimensions of guide pillar with taper lead (type C) shall conform to the indications of Figure 1 and Table 1. The dimensions of the bush for guide pillar

20、 with taper lead shall conform to the indications of Figure 2 and Table 1. The dimensions of the mounting of the bush on the pillar shall conform to the indications of Figure 3 and Table 1. ISO 2013 All rights reserved 1BS ISO 9182-4:2013ISO 9182-4:2013(E) Key 1 alternative 2 radius 3 centres 4 tape

21、r a Optional. b Slightly rounded. The values of the radii are left to the manufacturers discretion. Figure 1 Guide pillar with taper lead Key 1 taper Figure 2 Bush for guide pillar with taper lead Figure 3 Mounting of the bush on the pillar2 ISO 2013 All rights reservedBS ISO 9182-4:2013ISO 9182-4:2

22、013(E) Table 1 d 1 12 16 20 25 32 40 50 63 80 100 d 2 22 28 32 40 48 58 70 85 105 125 d 3 30 36 40 48 56 66 80 95 117 137 l 2min. 20 25 32 32 40 40 50 63 80 100 l 4 10 10 12 12 15 15 18 18 22 22 l 1min. 4 4 4 6 6 6 8 8 8 8 T 0,1 6,3 6,3 6,3 6,3 6,3 6,3 6,3 6,3 6,3 6,3 l 80 90 100 112 125 140 160 180

23、 200 224 250 280 315 355 400 450 NOTE 1 , standardized dimension. NOTE 2 Larger values of l 2shall be chosen as a function of other dimensions such as plate thickness in accordance with ISO 6753-1. NOTE 3 To prevent an incorrect assembly of the upper and lower plates of the die set in relation to ea

24、ch other, the following values of d 1are recommended: 11, 15, 19, 24, 30, 38, 48, and 60. 4 Material The material is left to the manufacturers discretion and the hardness shall be (60 ) HRC. 5 Designation Guide pillars for press tools in accordance with this part of ISO 9182 shall be designated by a

25、) “Guide pillar”; b) a reference to this part of ISO 9182, i.e. ISO 9182-4; c) its type; d) its diameter, d 1 , in millimetres; e) the bush length, l 2 , in millimetres; f) the length, l, in millimetres. ISO 2013 All rights reserved 3BS ISO 9182-4:2013ISO 9182-4:2013(E) EXAMPLE A guide pillar, type

26、C, of diameter d 1= 12 mm with a bush length l 2= 20 mm and a length l = 80 mm is designated as follows:Guide pillar ISO 91824 C 12 20 804 ISO 2013 All rights reservedBS ISO 9182-4:2013ISO 9182-4:2013(E) Bibliography 1 ISO 6508-1:2005, Metallic materials Rockwell hardness test Part 1: Test method (s

27、cales A, B, C, D, E, F, G, H, K, N, T) 2 ISO 9182-1:2013, Tools for pressing Guide pillars Part 1: Types ISO 2013 All rights reserved 5BS ISO 9182-4:2013ISO 9182-4:2013(E) ISO 2013 All rights reserved ICS 25.120.10 Price based on 5 pagesThis page deliberately left blankBSI is the national body respo

28、nsible for preparing British Standards and other standards-related publications, information and services. BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited. British Standards Institution (BSI) BSI Group Headquarters 389

29、 Chiswick High Road London W4 4AL UK About us We bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions. The knowledge embodied in our standards has been carefully assembled in a dependable form

30、at and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals. Information on standards We can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by

31、visiting our website at or contacting our Customer Services team or Knowledge Centre. Buying standards You can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If y

32、ou need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team. Subscriptions Our range of subscription services are designed to make using standards easier for you. For further information on our subscription pr

33、oducts go to With British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and recei

34、ve substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised

35、or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit With a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as

36、soon as theyre available, you can be sure your documentation is current. For further information, email . Revisions Our British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find

37、 an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre. Copyright All the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that

38、owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval sy

39、stem or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department. Useful Contacts: Customer Services Tel: +44 845 086 9001 Email (orders): Email (enquiries): Subscriptions Tel: +44 845 086 9001 Email: Knowledge Centre Tel: +44 20 8996 7004 Email: Copyright & Licensing Tel: +44 20 8996 7070 Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW