BS ISO 6279-2017 en_1419 Plain bearings Aluminium alloys for solid bearings《滑动轴承.实心轴承用铝合金》.pdf

《BS ISO 6279-2017 en_1419 Plain bearings Aluminium alloys for solid bearings《滑动轴承.实心轴承用铝合金》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 6279-2017 en_1419 Plain bearings Aluminium alloys for solid bearings《滑动轴承.实心轴承用铝合金》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BS ISO 6279:2017 Plain bearings Aluminium alloys for solid bearings BSI Standards Publication WB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS ISO 6279:2017 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO 6279:2017. It supersedes BS ISO 6279:2006 wh

2、ich is withdrawn. The UK participation in its preparation was entrusted to Technical Committee MCE/12, Plain bearings. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a con

3、tract. Users are responsible for its correct application. The British Standards Institution 2017. Published by BSI Standards Limited 2017 ISBN 978 0 580 92855 0 ICS 21.100.10; 77.120.10; 77.150.10 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard

4、 was published under the authority of the Standards Policy and Strategy Committee on 31 March 2017. Amendments/corrigenda issued since publication Date T e x t a f f e c t e dBS ISO 6279:2017 ISO 2017 Plain bearings Aluminium alloys for solid bearings Paliers lisses Alliages daluminium pour paliers

5、massifs INTERNATIONAL STANDARD ISO 6279 Third edition 2017-03 Reference number ISO 6279:2017(E)BS ISO 6279:2017ISO 6279:2017(E)ii ISO 2017 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2017, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication

6、may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of t

7、he requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.org www.iso.orgBS ISO 6279:2017ISO 6279:2017(E)Foreword iv 1 Scope . 1 2 Normative references 1 3 T erms and definitions . 1 4 Composition and me

8、chanical properties 1 4.1 Composition 1 4.2 Mechanical properties 1 5 Test methods . 1 6 Designation 2 ISO 2017 All rights reserved iii Contents PageBS ISO 6279:2017ISO 6279:2017(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodi

9、es (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations

10、, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further

11、maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directive

12、s). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Int

13、roduction and/or on the ISO list of patent declarations received (see www .iso .org/ patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the voluntary nature of standards, the meaning of ISO sp

14、ecific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: w w w . i s o .org/ iso/ foreword .html. This document was prepared by Technical

15、 Committee ISO/123, Plain bearings, Subcommittee SC 2, Materials and lubricants, their properties, characteristics, test methods and testing conditions. This third edition cancels and replaces the second edition (ISO 6279:2006), which has been technically revised.iv ISO 2017 All rights reservedBS IS

16、O 6279:2017INTERNATIONAL ST ANDARD ISO 6279:2017(E) Plain bearings Aluminium alloys for solid bearings 1 Scope This document specifies the composition and properties of preferred cast aluminium alloys for use in solid plain bearings. Other alloys can be specified with agreement between the manufactu

17、rer and user. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced docum

18、ent (including any amendments) applies. ISO 4384-2, Plain bearings Hardness testing of bearing metals Part 2: Solid materials 3 T erms a nd definiti ons No terms and definitions are listed in this document. ISO and IEC maintain terminological databases for use in standardization at the following add

19、resses: IEC Electropedia: available at h t t p :/ www .electropedia .org/ ISO Online browsing platform: available at h t t p :/ www .iso .org/ obp 4 Composition and mechanical properties 4.1 Composition Preferred compositions are given in Table 1. Methods of analysis shall be mutually agreed between

20、 the manufacturer and user. 4.2 Mechanical properties Mechanical properties are given in Table 1. Tensile strength and elongation are mandatory properties that are the subject of quality control checks carried out by the material manufacturers. Hardness is a mandatory property that may be checked on

21、 individual bearings. Typical values of other properties are given for design guidance. 5 Test methods The tensile test shall be carried out as agreed between the manufacturer and user. Test methods and mandatory values shall be agreed between the manufacturer and user. Hardness testing shall be car

22、ried out in accordance with ISO 4384-2. ISO 2017 All rights reserved 1BS ISO 6279:2017ISO 6279:2017(E) Table 1 Aluminium alloys Aluminium alloy AlSn6Cu AlSn6CuNi AlSn20Cu AlZn4,5SiCuMg AlZn5SiCuMg AlSi12CuMgNi Chemical composition (mass fraction in %) Chemical element Al Remainder Remainder Remainde

23、r Remainder Remainder Remainder Sn 5,5 to 6,5 5,5 to 7 17,5 to 22,5 0,2 max. 0,2 max. Cu 1,3 to 1,7 0,7 to 1,3 0,7 to 1,3 0,9 to 1,2 0,9 to 1,2 0,8 to 1,5 Ni 0,2 max. 0,7 to 1,3 0,2 max. 0,2 max. 1,3 max. Si 0,3 max. 0,7 max. 0,7 max. 1,0 to 2,0 1,2 to 2,0 11,0 to 13,0 Fe 0,4 max. 0,7 max. 0,7 max.

24、0,4 max. 0,6 max. 0,7 max. Mn 0,2 max. 0,1 max. 0,7 max. 0,3 max. 0,3 max. 0,3 max. Zn 0,2 max. 4,4 to 5,0 5,0 to 5,5 0,3 max. Mg 0,1 max. 0,4 to 0,6 0,4 to 0,6 0,8 to 1,3 Ti 0,05 to 0,2 0,2 max. 0,02 to 0,15 0,02 to 0,15 0,2 max. Total other elements, max. 0,5 0,5 0,5 0,5 0,5 0,5 Mechanical propert

25、ies Hardness Brinell HB10/1 000/10 35 to 40 35 to 45 30 to 55 48 to 56 50 to 60 90 to 120 Tensile strength R mMPa 130 to 140 110 to 140 110 to 130 160 to 200 180 to 220 200 to 250 Elongation A % 30 to 36 10 to 20 28 to 32 20 to 22 19 to 21 0,3 to 0,8 0,2 % Proof stress R p0,2MPa 50 to 60 45 to 60 40

26、 to 60 80 to 110 100 to 120 190 to 230 Elastic modulus E GPa 69 71 63 75 75 75 Thermal expansion 10 6 /K 23 23 24 23 23 21 Thermal conductivity W/(m K) 160 160 155 170 170 184 Density 10 3 kg/m 3 2,9 2,9 3,12 2,9 2,9 2,7 6 Designation The designation shall include the following information, in the o

27、rder given: a) “Aluminium alloy”; b) reference to this document, i.e. ISO 6279; c) name of alloy. EXAMPLE The aluminium alloy AlSn6Cu is designated by the following: Aluminium alloy ISO 6279 AlSn6Cu2 ISO 2017 All rights reservedBS ISO 6279:2017BS ISO 6279:2017ISO 6279:2017(E) ISO 2017 All rights res

28、erved IC S 77.150.10; 21.100.10 Price based on 2 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services. BSI is incorporated by Royal Charter. British Standards and other standardiz

29、ation products are published by BSI Standards Limited. British Standards Institution (BSI) About us We bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions. The knowledge embodied in our stand

30、ards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals. Information on standards We can provide you with the knowledge that your organization needs

31、 to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre. Buying standards You can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our web

32、site at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team. Copyright in BSI publications All the content in BSI publications, including British Standards

33、, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Save for the provisions below, you may not transfe

34、r, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior written consent. Storing and using standards Standards purchased in soft c

35、opy format: A British Standard purchased in soft copy format is licensed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 device provided that it is accessible by the sole named user only and that only 1 copy is accessed at any one time. A sin

36、gle paper copy may be printed for personal or internal company use only. Standards purchased in hard copy format: A British Standard purchased in hard copy format is for personal or internal company use only. It may not be further reproduced in any format to create an additional copy. This includes

37、scanning of the document. If you need more than 1 copy of the document, or if you wish to share the document on an internal network, you can save money by choosing a subscription product (see Subscriptions). Reproducing extracts For permission to reproduce content from BSI publications contact the B

38、SI Copyright & Licensing team. Subscriptions Our range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to With British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European

39、and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a B

40、SI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit With

41、a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email . Revisions Our B

42、ritish Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre. Useful

43、 Contacts Customer Services Tel: +44 345 086 9001 Email (orders): Email (enquiries): Subscriptions Tel: +44 345 086 9001 Email: Knowledge Centre Tel: +44 20 8996 7004 Email: Copyright & Licensing Tel: +44 20 8996 7070 Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK BSI Back Cover.indd 1 27/01/2016 14:20