ASTM C1302 - 04(2011) Standard Guide for Selection and Use of Keywords for Thermal Insulation Test Methods and Standards (Withdrawn 2017).pdf

《ASTM C1302 - 04(2011) Standard Guide for Selection and Use of Keywords for Thermal Insulation Test Methods and Standards (Withdrawn 2017).pdf》由会员分享，可在线阅读，更多相关《ASTM C1302 - 04(2011) Standard Guide for Selection and Use of Keywords for Thermal Insulation Test Methods and Standards (Withdrawn 2017).pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: C1302 04 (Reapproved 2011)Standard Guide forSelection and Use of Keywords for Thermal Insulation TestMethods and Standards1This standard is issued under the fixed designation C1302; the number immediately following the designation indicates the year oforiginal adoption or, in the case o

2、f revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This guide has been prepared for use by ASTM techni-cal committees and others in the preparati

3、on of ASTM stan-dards pertaining to thermal insulations and to materials asso-ciated with them.1.2 The keywords appear in alphabetical order.1.3 All ASTM standards require a list of appropriate termsfor indexing called Keywords. Keywords shall be listed at theend of the draft standard and will appea

4、r in the publisheddocument.2. Significance and Use2.1 The purpose of the keyword list is to provide a standardset of words that can be used in the preparation and referenceof documents. Keywords are used to search for information.2.2 Keywords are not defined in this guide.2.3 Words referring to the

5、singular include the plural also.3. Keywords3.1absorptionacousticaladhesionadhesiveaircraftaluminumaluminum foilapparentapplicationaustenitic stainless steelbacker boardbattsblack bodyblanketblockboardboil-off calorimeterbreaking loadbreaking strengthbubble-pack insulationbubble-pack reflective insu

6、lationbuilding envelopebuilding insulationbuilding technologybulk densityburn potentialcalcium silicatecalculated energy savingscalibrationcalorimeterceiling panelsceiling tilescellular glasscellular materialscellular plasticcellular polystyrenecellulosecellulosic fibercementchemical analysischlorid

7、ecoatingscompositecomposite foam insulation boardcompressive pressurecompressive resistancecompressive strengthcomputer programconditioningconsistencyconstruction and installationconvergence factorcorkcorrosioncrackingcryogenic temperaturescuring1This guide is under the jurisdiction of ASTM Committe

8、e C16 on ThermalInsulation and is the direct responsibility of Subcommittee C16.95 on Editorial.Current edition approved April 1, 2011. Published June 2011. Originallyapproved in 1995. Last previous edition approved in 2004 as C1302 04. DOI:10.1520/C1302-04R11.Copyright ASTM International, 100 Barr

9、Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesNOTICE: This standard has either been superseded and replaced by a new version or withdrawn.Contact ASTM International (www.astm.org) for the latest information1data time intervaldeflectiondeformationdelaminationdensitydesignd

10、esign densitydished head segmentdoorsduct linerduct workducts and equipmentdustdynamic measurementelectrolytic copperelevated temperatureemittanceerror analysisevacuated insulationevacuated reflective insulationexpanded perliteexpanded vermiculiteexpansionexperimental designexterior exposure testfac

11、ed foam boardfaced insulationfacingfeltfenestrationfibrous glassfinishingfire resistiveflanking lossflexibilityflexibleflexural strengthfluoridefoamfoil laminatesframe constructionfriabilityfull scale testingfungi resistanceglass fibergranulargranular loose-fillguarded hot plate apparatushealth haza

12、rdsheatheat flowheat flow meter apparatusheat fluxheat flux transducerheat gainheat lossheat transferhemisphericalhigh temperature calculationhigh temperature insulationhot-boxhot-surface performancehumid aginghydraulic-settingimmersionin-situ measurementindustrial applicationinfrared inspectioninor

13、ganic fiberinstrument verificationinsulating cementinsulationinsulation coverinsulation systeminterior radiation control coatingsintermediate density sheathinginterpretation of field dataIR emmitancejacketing materiallaminateleachable chlorideslengthlight frame constructionline source heaterlinear c

14、hangeslinearityliningloading testsloose filllow emittancelow permeancelow temperature insulationlow-densitymanufactured housingmass lossmasticmaterialmathematical modelmean test temperaturemechanical processmembrane-facedmetal buildingmetal-mesh coveredmetallic reflective insulationmethod of mixture

15、smineral fiberminimum use temperaturemodulus of elasticitymodulus of rupture (MOR)moisture contentmoldedmounting of heat flux transducersmulti-foil insulationmultilayer insulationsnormal emittancenuclear power plantC1302 04 (2011)2outdoor service vesselpaint-high reflectancepaint-high temperaturepai

16、nt-spray appliedparting strengthpenetrationperformance criteriaperlitepermeabilitypHphenolicphysical propertiespipe densitypipe insulationpipe systemspipe thermal insulation diameterpipe thermal insulation dimensionpipe thermal insulation thicknessplane and radial calculationplastic sheet and filmpl

17、astics (general)polyethylene terephthalate reference filmpolyisocyanuratepolystyrenepolyurethaneprecision V-groovepreconditioningprefabricated insulationprefabricated panelpreformedpreformed thermal insulationprogram verificationpropertiespseudo steady-statequality controlR-valueradial heat transfer

18、radiant barrier systemradiationradiation barrierradiation control coatingsradiative transportreflectancereflective air spacereflective coatingreflective insulationreflective linerreflective paintreflective pipe insulationreflective systemreflectivityregular density sheathingremovableremovable/reusab

19、lerepairrigidrigid cellular plasticrigid cellular polyisocyanuraterigid cellular polystyrenerigid cellular polyurethanerigidityroof deckroof inspectionroof insulationsamplingsampling and acceptance criteriaselecting temperaturesselectionselection and applicationsensor calibrationsensor locationsheet

20、sheet materialsheet radiant barriershrinkagesilicatesingle-sidedsoaking heat testsodiumsolar reflectancesound deadening boardspecific heatspray applicationspray appliedsquarenesssteady statestress corrosion crackingstructural insulationsummation techniquesurface resistancetemperature testtenacityten

21、sile strengthtensiontest specimen preparationthermalthermal capacitythermal conductancethermal conductivitythermal contactthermal diffusivitythermal insulating cementsthermal insulating materialthermal insulating materialsblanketthermal insulating materialsblock and boardthermal insulating materials

22、block and pipethermal insulating materialsboardthermal insulating materialscementthermal insulating materialsglassthermal insulating materialsloose fillthermal insulating materialsmineral fiberthermal insulating materialspipethermal insulating materialspreformedthermal insulating materialsreflective

23、thermal insulating materialsrigidthermal insulationC1302 04 (2011)3thermal insulation applicationthermal insulating fitting coverthermal insulation for austenitic stainless steelthermal insulation handlingthermal insulation permeability filmthermal insulation storagethermal integritythermal performa

24、ncethermal propertythermal resistancethermal resistivitythermal testingthermal transmissionthermesthesiometerthicknessthin-heater apparatustime-averaged vapor pressuretotal hemispherical emittancetransducer designtransducer sensitivitytransmission-water vaportransverse strengthtruenesstubing thermal

25、 insulation thicknesstubulartumble testU-valueunguarded hot platevapor barrier finishvapor retarderverificationvermiculitevessel laggingvolume changevolume losswall sheathingwarpagewater absorptionwater equivalentwater retentionwater vapor permeancewater vapor sorptionwater vapor transmissionwet cov

26、ering capacitywet insulationwidthwindowASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the

27、riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of

28、this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldma

29、ke your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).C1302 04 (2011)4