ISO TR 19961-2010 Cranes - Safety code on mobile cranes《起重机 移动式起重机的安全规程》.pdf

《ISO TR 19961-2010 Cranes - Safety code on mobile cranes《起重机 移动式起重机的安全规程》.pdf》由会员分享，可在线阅读，更多相关《ISO TR 19961-2010 Cranes - Safety code on mobile cranes《起重机 移动式起重机的安全规程》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、 Reference number ISO/TR 19961:2010(E) ISO 2010TECHNICAL REPORT ISO/TR 19961 Second edition 2010-11-01 Cranes Safety code on mobile cranes Appareils de levage charge suspendue Code de scurit sur les grues mobiles ISO/TR 19961:2010(E) PDF disclaimer This PDF file may contain embedded typefaces. In ac

2、cordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes

3、 licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for pr

4、inting. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2010 All rights reserved. Unless otherw

5、ise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright

6、office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2010 All rights reservedISO/TR 19961:2010(E) ISO 2010 All rights reserved iiiForeword ISO (the International Organization for Standardization)

7、 is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be repre

8、sented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are

9、 drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an Internationa

10、l Standard requires approval by at least 75 % of the member bodies casting a vote. In exceptional circumstances, when a technical committee has collected data of a different kind from that which is normally published as an International Standard (“state of the art”, for example), it may decide by a

11、simple majority vote of its participating members to publish a Technical Report. A Technical Report is entirely informative in nature and does not have to be reviewed until the data it provides are considered to be no longer valid or useful. Attention is drawn to the possibility that some of the ele

12、ments of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO/TR 19961 was prepared by Technical Committee ISO/TC 96, Cranes, Subcommittee SC 6, Mobile cranes. This second edition cancels and replaces the first editio

13、n (ISO/TR 19961:2005). Subclauses 4.2, 4.3 and 4.4 have been removed and these sections are now covered under ISO 10972-2. The Bibliography has been updated. TECHNICAL REPORT ISO/TR 19961:2010(E) ISO 2010 All rights reserved 1Cranes Safety code on mobile cranes 1 Scope This Technical Report provides

14、 a guide to International Standards applicable to mobile cranes (crawler cranes, railway cranes, wheel-mounted cranes and any variations thereof that retain the same fundamental characteristics) and a summary of related provisions. Special adaptations of the general types of machine covered, where a

15、pplicable, also fall within its scope. NOTE According to the ISO Directives, Part 2, the verbal forms used to identify provisions in an International Standard are “shall” or “shall not”, used to indicate requirements strictly to be followed in order to conform to the document and from which no devia

16、tion is permitted, “should” or “should not” for recommendations, indicating that among several possibilities one is recommended as particularly suitable, without mentioning or excluding others, or that a certain course of action is preferred but not necessarily required, or that (in the negative for

17、m) a certain possibility or course of action is deprecated but not prohibited, and “may” or “need not”, used to indicate a course of action permissible within the limits of the document. 2 Purpose The purpose of this Technical Report is to a) identify the many International Standards relevant to mob

18、ile cranes and their safety (see Bibliography for a complete listing), b) summarize the content of those documents, c) promote mobile crane safety by the delineation of these standards, so that the incorporation of their provisions into the design and use of mobile cranes will guard against, and min

19、imize, injury to workers and damage to equipment, d) facilitate the work of all those working in the field of mobile cranes (designers, supervisors and others either directly or indirectly responsible for the safe use and maintenance of the machines) with a need to consult the current standards rela

20、ting to mobile cranes, and e) contribute to further international harmonization of mobile crane standards. 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 4306-1 and ISO 4306-2 apply. ISO/TR 19961:2010(E) 2 ISO 2010 All rights reserved4 Construction

21、and characteristics 4.1 Load rating 4.1.1 Crane stability (backward/forward) ISO 4305 specifies the conditions to be taken into consideration when verifying the stability of a mobile crane by calculation, assuming that the crane is operating on a firm and level surface (up to 1 % gradient). It appli

22、es to mobile cranes defined in ISO 4306-2 mounted on wheels or crawlers with or without outriggers. 4.1.2 Crane structural competence ISO 8686-1 establishes general methods for calculating loads and principles to be used to select load combinations for proofs of competence for the structural and mec

23、hanical components of cranes. Based on rigid-body kinetic analysis and elasto-static analysis, it expressly permits the use of more advanced methods (calculations or tests) to evaluate the effects of loads and load combinations, and the value of dynamic load factors, where it can be demonstrated tha

24、t these provide at least equivalent levels of competence. It provides the general form, content and ranges of parameter values for more specific standards to be developed for individual lifting appliance types. It provides a framework for agreement on loads and load combinations between a designer o

25、r manufacturer and an appliance purchaser for those types of lifting appliances where specific standards do not exist. ISO 8686-2 applies the principles set forth in ISO 8686-1 to mobile cranes, as defined in ISO 4306-2, and presents loads and load combinations appropriate for use in proof of compet

26、ence calculations for the steel structures of mobile cranes. It applies to mobile cranes used for normal service and for duty cycle service. ISO 11662 specifies a test method that provides a systematic, non-destructive procedure for determining the stresses induced in crane structures under specifie

27、d conditions of static loading through the use of resistance type electronic strain gages and to specify appropriate acceptable criteria for specified loading conditions. 4.1.3 Wind load ISO 4302 relates to wind loads on cranes. It gives a simplified method of calculation and assumes that the wind c

28、an blow horizontally from any direction, that the wind blows at a constant velocity and that there is a static reaction to the loading it applies to the crane structure. It includes built-in allowances for the effects of gusting and for dynamic response. 4.1.4 Crane rating manuals ISO 11661 specifie

29、s a standard presentation or format for mobile crane rated capacities on rated capacity charts. It applies to mobile cranes fitted with booms as defined in ISO 4306-2, when used in lifting mode. 4.2 Mechanisms ISO 10972-2 establishes requirements specific to the mechanisms of mobile cranes, in addit

30、ion to the general requirements for cranes given in ISO 10972-1. These additional requirements concern: a) the arrangement, features and characteristics of the crane mechanisms, and b) the minimum requirements for certain mechanism components. ISO/TR 19961:2010(E) ISO 2010 All rights reserved 34.3 C

31、ontrols ISO 7752-1 establishes principles and requirements for the controls of lifting appliances. It deals with the arrangement of those controls which are used in positioning loads and serves as a general basis for the elaboration of detailed standards covering controls for particular types of lif

32、ting appliances. ISO 7752-2 establishes the arrangement, requirements and direction of movement of the basic controls for slewing, load hoisting and lowering and jib luffing and telescoping. Section 1 deals with bi-directional controls, while Section 2 (see Addendum 1 to ISO 7752-2:1985) covers the

33、basic arrangement and requirements for cross-shift levers (joysticks). 4.4 Wire rope and reeving accessories 4.4.1 Wire rope ISO 4308-1 specifies two methods for the selection of wire rope to be used on the types of lifting appliances designated in ISO 4306-1. This part establishes the minimum requi

34、rements for these wire ropes to have acceptable strength and performance levels with respect to design, application and maintenance of the appliance. ISO 4308-2 establishes values for the minimum practical utilization, Z p , as defined in ISO 4308-1, for ropes and rotation-resistant ropes used on mo

35、bile cranes. ISO 4309 details the care, maintenance (including fitting) and examination of wire rope in service on a crane, and enumerates the discard criteria which need to be applied to ensure the efficient and safe use of the crane. 4.4.2 Reeving ISO 8087 establishes values for the minimum ratio

36、of the pitch diameters of the drum and sheaves to the nominal diameter of the rope for hoisting and luffing operations. The nominal diameter of the rope is considered the base factor when applying the ratio. The use of this nominal diameter allows flexibility of application, as it is not limited to

37、crane mechanisms (mobile cranes are frequently constructed for multi-purpose duty, such as hook lifting, grabbing or magnet operation). 4.5 Cabin (operators station) ISO 8566-1 establishes specifications for the general requirements of cabins from which cranes are operated. Considerations include th

38、e conditions of use of the cabin. ISO 8566-2 establishes criteria for cabins for mobile cranes. These are intended to cover cabins only for crane operators and not for road travel. 4.6 Machine access, guards and restraints ISO 11660-1 and ISO 11660-2 specify requirements for steps, stairways, ladder

39、s, walkways, platforms, handrails, handholds, guardrails, and entrance openings which permit access to and from operator, inspection or maintenance platforms on mobile cranes. It also presents requirements for guards and restraints as related to moving parts. 4.7 General requirements ISO 2374 sets f

40、orth the recommended range of maximum capacities of cranes from 0,1 to 1 000 t and applies to all types of cranes. ISO/TR 19961:2010(E) 4 ISO 2010 All rights reserved4.8 Classification ISO 4301-1 establishes a general classification for cranes based on the number of operating cycles to be carried ou

41、t during the expected life of the crane with a load spectrum factor which represents a nominal state of loading. NOTE This is not to imply that the same method of stress calculation or testing will apply to all types of lifting appliances which come under the scope of ISO/TC 96. ISO 4301-2 establish

42、es a classification of mobile cranes and related crane mechanisms based on the number of operating cycles to be carried out during the expected life of the crane or mechanism and on a load spectrum factor which represents a nominal state of loading. 4.9 Graphic symbols, colours and signs ISO 7296-1

43、establishes general graphic symbols for use on the controls of cranes and colours for control buttons and signal lamps. It divides the symbols into those for basic directions of motion and on/off positions; those for operator controls; and information symbols. ISO 7296-2 establishes graphical symbol

44、s for use on operator control and other displays for mobile cranes. ISO 3864 prescribes safety colours and safety signs for the purposes of preventing accidents and health hazards and meeting emergencies. The use of safety colours and safety signs does not replace proper working instructions or prec

45、autionary measures. ISO 13200 outlines safety sign objectives, describes the basic safety sign formats, specifies colours for safety signs, and provides guidance on developing the various panels that together constitute a safety sign. 4.10 Information to be provided ISO 7363 presents the form of pre

46、sentation and content for the documents which a manufacturer should provide with cranes and lifting appliances. Such documents give technical information and include acceptance documents for the equipment to facilitate its installation, testing and use. ISO 9374-1 specifies information to be provide

47、d by the purchaser and the manufacturer so that the most suitable crane can be provided for the duty requirements and service conditions. ISO 9942-1 specifies the minimum requirements for labels for the identification (marking) and the operation of cranes. ISO 9928-1 gives requirements and recommend

48、ations on the contents of crane driving manuals. ISO 9928-2 gives requirements and recommendations on the contents of crane driving manuals for mobile cranes, including erection, use, dismantling, inspection and maintenance. ISO 10973 gives general requirements for the preparation of spare part manu

49、als for cranes. 4.11 Limiting and indicating devices ISO 10245-1 specifies general requirements for limiting and indicating devices for lifting appliances that are applicable to loads and motions, performance and environment. These devices restrict operation and/or provide the driver or other persons with operational information. Safe and reliable operation of limiters and indicators depends upon regular inspection and maintenance. ISO 10245-2 establishes specific requirements for limiting and indicating devices fitted to mobile cranes. Some bas