ISO 10295-2-2009 Fire tests for building elements and components - Fire testing of service installations - Part 2 Linear joint (gap) seals《建筑单元和构件的燃烧试验 服务设施的燃烧试.pdf

《ISO 10295-2-2009 Fire tests for building elements and components - Fire testing of service installations - Part 2 Linear joint (gap) seals《建筑单元和构件的燃烧试验 服务设施的燃烧试.pdf》由会员分享，可在线阅读，更多相关《ISO 10295-2-2009 Fire tests for building elements and components - Fire testing of service installations - Part 2 Linear joint (gap) seals《建筑单元和构件的燃烧试验 服务设施的燃烧试.pdf（32页珍藏版）》请在麦多课文档分享上搜索。

1、 Reference number ISO 10295-2:2009(E) ISO 2009INTERNATIONAL STANDARD ISO 10295-2 First edition 2009-02-01 Fire tests for building elements and components Fire testing of service installations Part 2: Linear joint (gap) seals Essais au feu pour les lments et composants de btiment Essai au feu des ins

2、tallations de service Partie 2: Joints dtanchit pour interstices linaires ISO 10295-2:2009(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded ar

3、e licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Detail

4、s of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem rel

5、ating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2009 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including ph

6、otocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in S

7、witzerland ii ISO 2009 All rights reservedISO 10295-2:2009(E) ISO 2009 All rights reserved iiiContents Page Foreword iv Introduction.v 1 Scope1 2 Normative references1 3 Terms and definitions .2 4 Symbols and abbreviated terms 3 5 Test equipment 3 6 Test conditions 4 7 Specimen preparation.4 8 Instr

8、umentation .9 9 Test procedure.10 10 General performance criteria .11 11 Expression of test results.12 12 Test report12 Annex A (normative) Movement, deflection and other configurations .15 Annex B (normative) Field of application.17 Annex C (informative) Commentary and guidance .20 Bibliography24 I

9、SO 10295-2:2009(E) iv ISO 2009 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each

10、 member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the Internationa

11、l Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards

12、 adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of

13、 patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 10295-2 was prepared by Technical Committee ISO/TC 92, Fire safety, Subcommittee SC 2, Fire containment. ISO 10295 consists of the following parts, under the general title Fire tests for building ele

14、ments and components Fire testing of service installations: Part 1: Penetration seals Part 2: Linear joint (gap) seals A Part 3 dealing with guidance on the use of a test configuration to establish the direct and extended fields of application for single-component penetration seals is under developm

15、ent. ISO 10295-2:2009(E) ISO 2009 All rights reserved vIntroduction This part of ISO 10295 describes test methods used to determine the fire resistive nature of joint seals when subjected to the standard fire-exposure conditions outlined in ISO 834-1. The test data generated by this International St

16、andard permit the classification of these various joint seals based on their intended use and fire resistance under the specified acceptance criteria of this part of ISO 10295. Joint seals are positioned in joints, voids, gaps or other discontinuities between or bounded by two or more supporting ele

17、ments. Normally such openings are denoted as “linear” because the length is greater than the width, defined by a typical ratio of at least 10:1 as in practice. Joints are present in buildings as a result of a) design to accommodate various movements induced by thermal differentials, seismic events a

18、nd wind loads and exist as a clearance separation; b) acceptable dimensional tolerances between two or more building elements, e.g. between non-load-bearing walls and floors; c) inadequate design, inaccurate assembly, repairs or damage to the building. This part of ISO 10295 describes methods of tes

19、t for evaluating joint seals based on their intended use. This part of ISO 10295 also allows for the application of movement prior to and/or during fire testing. This part of ISO 10295 provides the requirements for the test specimen, the test construction, the equipment (including any special appara

20、tus or instrumentation), the procedures and acceptance criteria as they apply to joint seals and their supporting elements. INTERNATIONAL STANDARD ISO 10295-2:2009(E) ISO 2009 All rights reserved 1Fire tests for building elements and components Fire testing of service installations Part 2: Linear jo

21、int (gap) seals CAUTION The attention of all persons concerned with managing and carrying out this fire- resistance test is drawn to the fact that fire testing can be hazardous and that there is a possibility that toxic and/or harmful smoke and gases can be evolved during the test. Mechanical and op

22、erational hazards can also arise during the construction of the test elements or structures, their testing and disposal of test residues. An assessment of all potential hazards and risks to health shall be made and safety precautions shall be identified and provided. Written safety instructions shal

23、l be issued. Appropriate training shall be given to relevant personnel. Laboratory personnel shall ensure that they follow written safety instructions at all times. 1 Scope This part of ISO 10295 specifies the heating conditions, methods of test and criteria for the evaluation of the ability of a li

24、near joint seal to maintain the fire integrity and thermal insulation of a fire-separating element at the joint being sealed. The purpose of the tests is to assess the integrity and insulation performance of the linear joint seals, including the effects of induced movement in those cases where the j

25、oint is designed to accommodate movement and has a width greater than 20 mm. It is not the intention of this part of ISO 10295 to provide quantitative information on the rate of leakage of smoke and/or gases, or on the transmission or generation of fumes, although such phenomena can be recorded in d

26、escribing the general behaviour of specimens during the test. It is not the intention of this part of ISO 10295 to evaluate joint seals where special test procedures already exist, e.g. doors, partitions, penetrations, pipes, ducts and cables. 2 Normative references The following referenced document

27、s are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 834-1, Fire-resistance tests Elements of building construction Part 1: General

28、 requirements ISO 13943, Fire safety Vocabulary ISO 10295-2:2009(E) 2 ISO 2009 All rights reserved3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 13943 and the following apply. 3.1 blockout recess created in the supporting construction to allow the i

29、nstallation of the joint seal NOTE It is typically not required on all joint seals. 3.2 fire-separating element floor, wall or other separating element of construction having a period of fire resistance determined in accordance with ISO 834-1 3.3 joint linear void having a length to width ratio of a

30、t least 10:1 between or within two juxtaposed elements NOTE Typical locations of joints include floors, the perimeter of floors, walls, ceilings and roofs. 3.4 joint seal system designed to maintain the fire-separating function and, where required, to accommodate a specified degree of movement 3.5 m

31、aximum joint width widest opening an installed joint seal is intended to tolerate NOTE It is stated by the manufacturer or test sponsor. 3.6 minimum joint width narrowest opening an installed joint seal is intended to tolerate NOTE It is stated by the manufacturer or test sponsor. 3.7 nominal joint

32、width specified opening of a joint in practice NOTE It is selected by the manufacturer or test sponsor. 3.8 splice connection or junction within the length of a joint seal 3.9 supporting construction fire-separating elements into which joint seals are installed 3.10 termination special design detail

33、s applied at the ends of a joint seal 3.11 test construction complete assembly of test specimens together with their supporting construction ISO 10295-2:2009(E) ISO 2009 All rights reserved 33.12 test specimen joint seal of specific materials, design and dimensions 3.13 transition change in a direct

34、ion in a joint seal, e.g. from horizontal to vertical in a wall construction, or through 90 at the perimeter of a floor slab 4 Symbols and abbreviated terms For the purposes of this part of ISO 10295, the symbols and abbreviated terms given in ISO 834-1, together with the following, apply. Table 1 S

35、ymbol description Symbol Description D supSupporting element thickness f Deflection as function of the fire-resistance time F movMovement capability factor l 1Minimum furnace width l 2Thickness of supporting construction l 3Minimum 305 mm l 4Minimum 610 mm for horizontal supporting construction and

36、458 mm for vertical supporting construction l 5Minimum twice the thickness of supporting construction W MAXMaximum joint width W MINMinimum joint width W NOMNominal joint width 5 Test equipment 5.1 Test equipment specified in ISO 834-1, which is applicable to all joint seals tested within the scope

37、of this part of ISO 10295. 5.2 Test furnace, with internal dimensions such that a distance of at least 200 mm exists between the side or long edge of a linear joint and the furnace boundary, subject to a minimum internal size of 1 m 1 m 1 m for horizontal (floor) furnaces. For vertical (wall) furnac

38、es, the minimum internal size of the furnace shall be 1 m 1 m and of sufficient depth to ensure that the temperature conditions specified in ISO 834-1 can be achieved, that the pressure conditions described in 6.2 can be achieved and that the test specimen is not subject to direct flame impingement

39、at any time during the conduct of a test. 5.3 Apparatus used for cycling of the test specimens prior to the fire test, capable of continuous and repetitive movement between two specified points that cycles the test specimen between the minimum and maximum joint widths, and be equipped with an automa

40、tic counter capable of displaying the number of completed cycles. ISO 10295-2:2009(E) 4 ISO 2009 All rights reserved6 Test conditions 6.1 Heating conditions The heating conditions shall conform to ISO 834-1. 6.2 Pressure 6.2.1 For vertical test constructions, the furnace shall be operated such that

41、a minimum pressure of 20 Pa exists at the bottom of any test specimen. 6.2.2 In vertical elements, all splices shall be located within the positive pressure zone so that the pressure at the bottom of the splice is a minimum of 20 Pa for the lowest splice in the test construction. 6.2.3 For horizonta

42、l test constructions, the furnace shall be operated such that a minimum pressure of 20 Pa is established at a position (100 10) mm below the lowest point of the test construction. 6.3 Load Where applicable, a load shall be applied in accordance with the principles of ISO 834-1. 6.4 Movement Where th

43、e seal is greater than 20 mm wide and is designed to accommodate movement, the joint shall be cycled prior to the test in accordance with Annex A using the information required in 7.8.4. 7 Specimen preparation 7.1 Supporting construction The supporting construction shall be of known fire resistance

44、and representative of that used in practice. 7.2 Test construction 7.2.1 For the purposes of tests, joints can be formed in slabs or by adjacent discrete members; see Figure 1. ISO 10295-2:2009(E) ISO 2009 All rights reserved 5Key 1 linear joints 2 monolithic slab, single joint adjacent 3 monolithic

45、 slab, multiple joints adjacent 4 discrete members, single joint 5 discrete members, multiple joints aSupporting constructions made of monolithic slabs may be used only for testing static joints. Figure 1 Supporting construction 7.2.2 A test construction may consist of multiple variations in test-sp

46、ecimen widths, joint configurations, test-specimen configurations, joint-face positions and supporting elements of varying thickness, see Figures 2 and 3. Key 1 supporting construction 2 linear joint (single-stage joint) 3 linear joint with blockouts 4 linear offset joint (multi-stage joint) Figure

47、2 Joint configuration ISO 10295-2:2009(E) 6 ISO 2009 All rights reservedKey 1 supporting construction 2 test specimen fills joint 3 test specimen at bottom of joint 4 test specimen at top of joint 5 test specimen forms one or more air cavities 6 test specimen centred in joint Figure 3 Test-specimen

48、orientation in joint 7.2.3 The minimum width of the supporting elements between joint edges shall be 200 mm or 2T, whichever is greater. 7.2.4 The minimum distance between a joint edge and an adjacent blockout edge shall be 200 mm or 2T, whichever is greater. ISO 10295-2:2009(E) ISO 2009 All rights

49、reserved 7Key 1 supporting construction test specimen 2 test specimen 3 interior furnace face 4 joint edge 5 blockout edge l 1minimum furnace width l 2thickness of supporting construction l 3minimum 305 mm l 4minimum 610 mm for horizontal supporting construction and 458 mm for vertical supporting construction l 5minimum twice the thickness of supporting construction Figure 4 Cross-sectional view of test construction with minimum separation distances 7.3 Joint seal 7.3.1 All materials used