IEEE 60079-30-1-2015 en Explosive atmospheres C Part 30-1 Electrical resistance trace heating C General and testing requirements《易爆气体 第30-1部分 电阻丝加热 总则和试验要求》.pdf

《IEEE 60079-30-1-2015 en Explosive atmospheres C Part 30-1 Electrical resistance trace heating C General and testing requirements《易爆气体 第30-1部分 电阻丝加热 总则和试验要求》.pdf》由会员分享，可在线阅读，更多相关《IEEE 60079-30-1-2015 en Explosive atmospheres C Part 30-1 Electrical resistance trace heating C General and testing requirements《易爆气体 第30-1部分 电阻丝加热 总则和试验要求》.pdf（74页珍藏版）》请在麦多课文档分享上搜索。

1、IEC/IEEE 60079-30-1 Edition 1.0 2015-09 INTERNATIONAL STANDARD Explosive atmospheres Part 30-1: Electrical resistance trace heating General and testing requirements IEC/IEEE60079-30-1:2015-09(en) colourinsideTHIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2015 IEC, Geneva, Switzerland Copyright 20

2、15 IEEE All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing being secured. Requests for permission to reproduce should be

3、addressed to either IEC at the address below or IECs member National Committee in the country of the requester or from IEEE. IEC Central Office Institute of Electrical and Electronics Engineers, Inc. 3, rue de Varemb 3 Park Avenue CH-1211 Geneva 20 New York, NY 10016-5997 Switzerland United States o

4、f AmericaTel.: +41 22 919 02 11 stds.iprieee.org Fax: +41 22 919 03 00 www.ieee.org infoiec.ch www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and relate

5、d technologies. About the IEEE IEEE is the worlds largest professional association dedicated to advancing technological innovation and excellence for the benefit of humanity. IEEE and its members inspire a global community through its highly cited publications, conferences, technology standards, and

6、 professional and educational activities. About IEC/IEEE publications The technical content of IEC/IEEE publications is kept under constant review by the IEC and IEEE. Please make sure that you have the latest edition, a corrigendum or an amendment might have been published. IEC Catalogue - webstore

7、.iec.ch/catalogue The stand-alone application for consulting the entire bibliographical information on IEC International Standards, Technical Specifications, Technical Reports and other documents. Available for PC, Mac OS, Android Tablets and iPad. IEC publications search - www.iec.ch/searchpub The

8、advanced search enables to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just P

9、ublished details all new publications released. Available online and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms

10、in 15 additional languages. Also known as the International Electrotechnical Vocabulary (IEV) online. IEC Glossary - std.iec.ch/glossary More than 60 000 electrotechnical terminology entries in English and French extracted from the Terms and Definitions clause of IEC publications issued since 2002.

11、Some entries have been collected from earlier publications of IEC TC 37, 77, 86 and CISPR. IEC Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. IEC/IEEE 60079-30-1

12、 Edition 1.0 2015-09 INTERNATIONAL STANDARD Explosive atmospheres Part 30-1: Electrical resistance trace heating General and testing requirements INTERNATIONAL ELECTROTECHNICAL COMMISSION ICS 29.260.20 IEC ISBN 978-2-8322-2758-9 Warning! Make sure that you obtained this publication from an authorize

13、d distributor. Registered trademark of the International Electrotechnical Commission colourinsideIEEE ISBN 978-0-7381-9846-0 2 IEC/IEEE 60079-30-1:2015 IEC/IEEE 2015 CONTENTS FOREWORD . 5 INTRODUCTION . 10 1 Scope 11 2 Normative references 15 3 Terms and definitions 16 4 General requirements 22 4.1

14、General . 22 4.2 Mechanical strength 22 4.3 Terminations and connections . 23 4.4 Circuit protection requirements for branch circuits. 23 4.5 Temperature requirements 23 4.5.1 General . 23 4.5.2 Stabilized design . 24 4.5.3 Controlled design. 24 5 Testing 26 5.1 Type tests . 26 5.1.1 General . 26 5.

15、1.2 Dielectric test 26 5.1.3 Electrical insulation resistance test 27 5.1.4 Flammability test . 27 5.1.5 Impact tests . 29 5.1.6 Deformation test 32 5.1.7 Cold bend test . 32 5.1.8 Water resistance test . 33 5.1.9 Integral components resistance to water test . 33 5.1.10 Verification of rated output

16、. 34 5.1.11 Thermal stability of electrical insulating material 36 5.1.12 Thermal performance test 36 5.1.13 Determination of maximum sheath temperature . 38 5.1.14 Verification of start-up current . 46 5.1.15 Verification of the electrical resistance of electrically conductive covering 46 5.1.16 Ou

17、tdoor exposure test . 47 5.2 Routine tests. 47 5.2.1 Dielectric test 47 5.2.2 Verification of rated output . 47 6 Marking . 47 6.1 Product markings for trace heaters . 47 6.2 Markings for field assembled components . 48 7 Documentation requirements . 48 7.1 General . 48 7.2 Circuit design documentat

18、ion 48 7.3 Trace heating system documentation 49 7.3.1 General . 49 IEC/IEEE 60079-30-1:2015 3 IEC/IEEE 2015 7.3.2 For trace heating systems according to the product classification method 49 7.3.3 For trace heating systems according to stabilized design method 49 7.3.4 For trace heating systems acco

19、rding to controlled design method 49 7.4 Instructions for installation of trace heating system . 50 7.5 Instructions for commissioning 50 7.6 Instructions for maintenance / repair or modification . 50 Annex A (informative) Type test matrix for EPLs Gb/Gc/Db/Dc (Refer to IEC 60079-14 for the relation

20、ship of EPLs to Zones) . 52 Annex B (informative) Checklist for installation 53 Annex C (normative) Trace heater product design verification methodology . 54 C.1 General . 54 C.2 Design methodology and selection of trace heaters 54 C.3 Stabilized design calculations . 54 C.4 Trace heater performance

21、 and equilibrium conditions . 55 C.5 Heat loss calculations . 57 C.6 Heat loss design safety factor . 58 C.7 Maximum temperature determination 58 C.7.1 Theoretical pipe and sheath temperature calculations Metallic applications . 58 C.7.2 Theoretical vessel and sheath temperature calculations Metalli

22、c applications . 59 C.7.3 Sheath temperature metallic applications utilizing a temperature limiter control sensing the trace heater sheath or an artificial hot spot . 60 C.7.4 Theoretical sheath temperature calculations Non-metallic applications . 60 C.7.5 Sheath temperature non-metallic application

23、s utilizing a temperature limiter control sensing the trace heater sheath or an artificial hot spot . 62 Annex D (normative) Requirements for Division 1 and Division 2 trace heating systems 63 D.1 Application 63 D.2 General . 63 D.3 Terminations and connections . 63 D.4 Control and temperature requi

24、rements 63 D.4.1 General . 63 D.4.2 Stabilized design . 63 D.4.3 Controlled design. 64 D.4.4 Requirements for protective device in Divisions 1 and 2 64 D.5 Type tests . 64 D.5.1 Division 1 trace heating equipment 64 D.5.2 Division 2 equipment . 65 D.6 Marking . 65 D.7 Instructions Installation requi

25、rements . 65 Annex E (normative) Type test matrix for Division 1 and 2 explosive atmospheres . 67 Bibliography 69 Figure 1 Flammability test 28 Figure 2 Example of room temperature impact test 30 Figure 3 Example of minimum temperature impact test 31 Figure 4 Cold bend test 33 4 IEC/IEEE 60079-30-1:

26、2015 IEC/IEEE 2015 Figure 5 Integral components resistance to water test 34 Figure 6 Verification of rated output . 35 Figure 7 Maximum sheath temperature using product classification approach 39 Figure 8 Verification of sheath temperatures using pipe sculpture 41 Figure 9 Verification of sheath tem

27、perature, plate test . 44 Figure 10 Verification of sheath temperature plate test with serpentined sample . 44 Figure 11 Plate test with two samples crossed over . 45 Figure 12 Plate test with a single sample crossed over 46 Figure C.1 Equilibrium conditions for workpiece maintenance 55 Figure C.2 E

28、quilibrium conditions for upper limit evaluation . 56 Table 1 Application or exclusion of specific clauses of IEC 60079-0 . 11 Table 2 Sheath temperature design conditions based on equipment protection levels Stabilized design approach 24Table 3 Sheath temperature design conditions based on equipmen

29、t protection levels EPLs Controlled design approach 25 Table 4 Test voltages for the dielectric test 26 Table A.1 Determination of test samples 52 Table B.1 Trace heater installation record Example 53 Table D.1 Division trace heating systems . 63 Table D.2 Sheath temperature design conditions Stabil

30、ized design approach . 64 Table D.3 Sheath temperature design conditions With temperature control device 64 Table E.1 Applicable trace heater and trace heater pads and panels tests by installation location . 67 Table E.2 Applicable tests for integral components with trace heaters and trace heater pa

31、ds and panels. 68 IEC/IEEE 60079-30-1:2015 5 IEC/IEEE 2015 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ EXPLOSIVE ATMOSPHERES Part 30-1: Electrical resistance trace heating General and testing requirements FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for

32、 standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publish

33、es International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may par

34、ticipate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEEE Standards documents are developed within IEEE Societies and Standards Coordinating Committees of the IEEE Standards Association (IEEE-SA)

35、 Standards Board. IEEE develops its standards through a consensus development process, approved by the American National Standards Institute, which brings together volunteers representing varied viewpoints and interests to achieve the final product. Volunteers are not necessarily members of IEEE and

36、 serve without compensation. While IEEE administers the process and establishes rules to promote fairness in the consensus development process, IEEE does not independently evaluate, test, or verify the accuracy of any of the information contained in its standards. Use of IEEE Standards documents is

37、wholly voluntary. IEEE documents are made available for use subject to important notices and legal disclaimers (see http:/standards.ieee.org/IPR/disclaimers.html for more information). IEC collaborates closely with IEEE in accordance with conditions determined by agreement between the two organizati

38、ons. This Dual Logo International Standard was jointly developed by the IEC and IEEE under the terms of that agreement. 2) The formal decisions of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee ha

39、s representation from all interested IEC National Committees. The formal decisions of IEEE on technical matters, once consensus within IEEE Societies and Standards Coordinating Committees has been reached, is determined by a balanced ballot of materially interested parties who indicate interest in r

40、eviewing the proposed standard. Final approval of the IEEE standards document is given by the IEEE Standards Association (IEEE-SA) Standards Board. 3) IEC/IEEE Publications have the form of recommendations for international use and are accepted by IEC National Committees/IEEE Societies in that sense

41、. While all reasonable efforts are made to ensure that the technical content of IEC/IEEE Publications is accurate, IEC or IEEE cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Com

42、mittees undertake to apply IEC Publications (including IEC/IEEE Publications) transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC/IEEE Publication and the corresponding national or regional publication shall be clearly indicated in

43、 the latter. 5) IEC and IEEE do not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC and IEEE are not responsible for any services carried out by independent certification bodies.

44、 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or IEEE or their directors, employees, servants or agents including individual experts and members of technical committees and IEC National Committees, or volunteers of IEEE Societi

45、es and the Standards Coordinating Committees of the IEEE Standards Association (IEEE-SA) Standards Board, for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, us

46、e of, or reliance upon, this IEC/IEEE Publication or any other IEC or IEEE Publications. 8) Attention is drawn to the normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the poss

47、ibility that implementation of this IEC/IEEE Publication may require use of material covered by patent rights. By publication of this standard, no position is taken with respect to the existence or validity of any patent rights in connection therewith. IEC or IEEE shall not be held responsible for i

48、dentifying Essential Patent Claims for which a license may be required, for conducting inquiries into the legal validity or scope of Patent Claims or determining whether any licensing terms or conditions provided in connection with submission of a Letter of Assurance, if any, or in any licensing agr

49、eements are reasonable or non-discriminatory. Users of this standard are expressly advised that determination of the validity of any patent rights, and the risk of infringement of such rights, is entirely their own responsibility. 6 IEC/IEEE 60079-30-1:2015 IEC/IEEE 2015 International Standard IEC/IEEE 60079-30-1 has been prepared by IEC technical committee 31: Equipment for explosive atmospheres, in cooperation with the Petroleum x the addition of a m