IEC 61169-14-2010 Radio-frequency connectors - Part 14 R.F coaxial connectors with inner diameter of outer conductor 12 mm with screw coupling - Characteristic .pdf

《IEC 61169-14-2010 Radio-frequency connectors - Part 14 R.F coaxial connectors with inner diameter of outer conductor 12 mm with screw coupling - Characteristic .pdf》由会员分享，可在线阅读，更多相关《IEC 61169-14-2010 Radio-frequency connectors - Part 14 R.F coaxial connectors with inner diameter of outer conductor 12 mm with screw coupling - Characteristic .pdf（62页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 61169-14 Edition 1.0 2010-10 INTERNATIONAL STANDARD NORME INTERNATIONALE Radio-frequency connectors Part 14: R.F. coaxial connectors with inner diameter of outer conductor 12 mm with screw coupling Characteristic impedance 75 ohms (Type 3,5/12) Connecteurs pour frquences radiolectriques Partie

2、14: Connecteurs coaxiaux pour frquences de diamtre intrieur du conducteur extrieur de 12 mm verrouillage vis Impdance caractristique 75 ohms (Type 3,5/12) IEC 61169-14:2010 colour inside THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2010 IEC, Geneva, Switzerland All rights reserved. Unless other

3、wise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any ques

4、tions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne pe

5、ut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez

6、 obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrot

7、echnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that y

8、ou have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, with

9、drawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available on-line and also by email. Electropedia: www.electropedia.org The worlds leading online dicti

10、onary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary online. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to gi

11、ve us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qu

12、i labore et publie des normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrig

13、endum ou amendement peut avoir t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue en-ligne de la CEI vous permet deffectuer des recherches en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Il donne aussi des informations sur les proj

14、ets et les publications retires ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvelles publications de la CEI. Just Published dtaille deux fois par mois les nouvelles publications parues. Disponible en-ligne et aussi par email. Electropedia: www.electropedia

15、.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 20 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International en ligne. Service

16、 Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du Service clients ou contactez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC 61169-14 Edition 1.0 2010

17、-10 INTERNATIONAL STANDARD NORME INTERNATIONALE Radio-frequency connectors Part 14: R.F. coaxial connectors with inner diameter of outer conductor 12 mm with screw coupling Characteristic impedance 75 ohms (Type 3,5/12) Connecteurs pour frquences radiolectriques Partie 14: Connecteurs coaxiaux pour

18、frquences de diamtre intrieur du conducteur extrieur de 12 mm verrouillage vis Impdance caractristique 75 ohms (Type 3,5/12) INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE U ICS 33.120.30 PRICE CODE CODE PRIX ISBN 978-2-88912-161-8 Registered trademark of the In

19、ternational Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale colour inside 2 61169-14 IEC:2010 CONTENTS FOREWORD.4 1 Scope.6 2 Normative references .6 3 IEC type designation 6 4 Mating face for general purpose connector .7 4.1 Connector with pin centre contac

20、t7 (see Figure 1).7 4.2 Connector with socket centre contact 8 (see Figure 2).8 5 Gauges and standard test connectors 9 5.1 Mechanical gauges9 5.1.1 Socket connector.9 5.2 Standard test connectors (Grade 0).9 5.2.1 General .9 5.2.2 Standard test connectors with pin centre contact.9 5.2.3 Standard te

21、st connectors with socket centre contact10 6 Survey of patterns 10 7 Outline dimensions.12 8 Quality assessment procedures16 8.1 General .16 8.2 Ratings and characteristics .16 8.3 Test schedule and inspection requirements.18 8.3.1 Acceptance tests .18 8.3.2 Periodic tests 19 8.4 Procedures20 8.4.1

22、Quality conformance inspection.20 8.4.2 Qualification approval and its maintenance20 9 Instructions for preparation of detail specifications .21 9.1 General .21 9.2 Identification of the detail specification22 9.3 Identification of the component22 9.4 Performance22 9.5 Marking, ordering information

23、and related matters.22 9.6 Selection of tests, test conditions and severities22 10 Blank detail specification pro-forma for type 3.5/12 connector 24 Figure 1 Connector with pin centre contact (for dimensions, see Table 1).7 Figure 2 Connector with socket centre contact (for dimensions, see Table 2)8

24、 Figure 3 Gauge pins for centre contact of socket connector .9 Figure 4 Slotted centre contact 10 Table 1 Dimensions for connector with pin centre contact 7 Table 2 Dimensions for connector with socket centre contact.8 Table 3 Dimensions for connector with pin centre contact Grade 0 9 61169-14 IEC:2

25、010 3 Table 4 Dimensions for connector with socket centre contact Grade 0 .10 Table 5 Survey of patterns.10 Table 6 Outline dimensions13 Table 7 Rating and characteristic.16 Table 8 Acceptance tests.18 Table 9 Periodic tests 19 4 61169-14 IEC:2010 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ RADIO-FR

26、EQUENCY CONNECTORS Part 14: R.F. coaxial connectors with inner diameter of outer conductor 12 mm with screw coupling Characteristic impedance 75 ohms (Type 3,5/12) FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national

27、electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Spe

28、cifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. Intern

29、ational, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The for

30、mal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations f

31、or international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user.

32、4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication sha

33、ll be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certi

34、fication bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal inj

35、ury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references

36、cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identi

37、fying any or all such patent rights. International Standard IEC 61169-14 has been prepared by subcommittee 46F: RF and microwave passive components, of IEC technical committee 46: Cables, wires, waveguides, R.F. connectors, R.F. and microwave passive components and accessories. This first edition ca

38、ncels and replaces IEC 60169-14 published in 1977. This edition constitutes a technical revision. The text of this standard is based on the following documents: FDIS Report on voting 46F/148/CDV 46F/169/RVD Full information on the voting for the approval of this standard can be found in the report o

39、n voting indicated in the above table. 61169-14 IEC:2010 5 This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts of the IEC 61169 series, under the general title: Radio-frequency connectors, can be found on the IEC website. A bilingual version may b

40、e issued at a later date. The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfi

41、rmed, withdrawn, replaced by a revised edition, or amended. IMPORTANT The colour inside logo on the cover page of this publication indicates that it contains colours which are considered to be useful for the correct understanding of its contents. Users should therefore print this document using a co

42、lour printer. 6 61169-14 IEC:2010 RADIO-FREQUENCY CONNECTORS Part 14: R.F. coaxial connectors with inner diameter of outer conductor 12 mm with screw coupling Characteristic impedance 75 ohms (Type 3,5/12) 1 Scope This standard concerns RF coaxial connectors for use with RF cables both flexible and

43、semi- rigid, where air dielectric interface and high mechanical stability is required for severe environmental exposure. The connectors provide low reflection in the microwave region up to 12 GHz and all patterns may provide sealing up to a pressure differential of 3 bar. For this type of connector,

44、 cables IEC 75-7-and 75-8 of IEC 61196-6: Coaxial communication cables Part 6: Sectional specification for CATV drop cables, are recommended. This type is known commercially as the 3,5/12 connector. 2 Normative references The following referenced documents are indispensable for the application of th

45、is document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 61169-1:1992, Radio-frequency connectors Part 1: Generic specification General requirements and measuring methods 1Amendmen

46、t 1 (1996) Amendment 2 (1997) 3 IEC type designation Connectors conforming to this standard shall be designated by: a) the reference to this standard: 61169-14 IEC; b) number of the grade: Grade 0 = standard test connector = G0 Grade 1 = high performance connector = G1 Grade 2 = general purpose conn

47、ector if Grade 2 is required, no grade designation is necessary; c) a serial number (see Clause 7); d) a group of figures specifying the climatic category (see Clause 4). Example 61169-14 IEC-Gl-1 (40/85/21) denotes a free pin Grade 1 high performance connector (straight) for cable 96-2 IEC 75-7-1/2

48、/8 with mating face as indicated in Clause 5 of this standard with a reflection coefficient not greater than 0,06 at frequencies up to 6 GHz belonging to climatic category 40/85/21. _ 1There exists a consolidated edition 1.2 (1998) that comprises IEC 61169-1:1992, its Amendment 1:1996 and its Amendm

49、ent 2:1997. 61169-14 IEC:2010 7 4 Mating face for general purpose connector 4.1 Connector with pin centre contact (see Figure 1) k h i c b a g f Note 4 d e IEC 1983/10Figure 1 Connector with pin centre contact (for dimensions, see Table 1) Table 1 Dimensions for connector with pin centre contact mm Note Ref. Min. Max. a M 20 1 2 b 14,84 14,95