IEC 61347-2-7-2011 Lamp controlgear - Part 2-7 Particular requirements for battery supplied electronic controlgear for emergency lighting (self-contained)《灯的控制装置.第2-7部分 应急照明用蓄电池供电电子控制装置的特殊要求(自含)》.pdf

《IEC 61347-2-7-2011 Lamp controlgear - Part 2-7 Particular requirements for battery supplied electronic controlgear for emergency lighting (self-contained)《灯的控制装置.第2-7部分 应急照明用蓄电池供电电子控制装置的特殊要求(自含)》.pdf》由会员分享，可在线阅读，更多相关《IEC 61347-2-7-2011 Lamp controlgear - Part 2-7 Particular requirements for battery supplied electronic controlgear for emergency lighting (self-contained)《灯的控制装置.第2-7部分 应急照明用蓄电池供电电子控制装置的特殊要求(自含)》.pdf（74页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 61347-2-7 Edition 3.0 2011-12 INTERNATIONAL STANDARD NORME INTERNATIONALE Lamp controlgear Part 2-7: Particular requirements for battery supplied electronic controlgear for emergency lighting (self-contained) Appareillages de lampes Partie 2-7: Rgles particulires relatives aux appareillages lec

2、troniques aliments par batterie pour lclairage de secours (autonome) IEC61347-2-7:2011 colourinsideTHIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2011 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or

3、 by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this p

4、ublication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectroni

5、que ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-apr

6、s ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes

7、 International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Cata

8、logue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay

9、 up to date on all new IEC publications. Just Published details twice a month all new publications released. Available on-line and also by email. Electropedia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitio

10、ns in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary online. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Cus

11、tomer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llect

12、ronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue des publications de la CEI: www.iec.ch

13、/searchpub/cur_fut-f.htm Le Catalogue en-ligne de la CEI vous permet deffectuer des recherches en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Il donne aussi des informations sur les projets et les publications retires ou remplaces. Just Published CEI: www.iec.ch/online_news

14、/justpub Restez inform sur les nouvelles publications de la CEI. Just Published dtaille deux fois par mois les nouvelles publications parues. Disponible en-ligne et aussi par email. Electropedia: www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il

15、contient plus de 20 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International en ligne. Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner d

16、es commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du Service clients ou contactez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC 61347-2-7 Edition 3.0 2011-12 INTERNATIONAL STANDARD NORME INTERNATIONALE Lamp controlgear Part 2-7: Particular r

17、equirements for battery supplied electronic controlgear for emergency lighting (self-contained) Appareillages de lampes Partie 2-7: Rgles particulires relatives aux appareillages lectroniques aliments par batterie pour lclairage de secours (autonome) INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISS

18、ION ELECTROTECHNIQUE INTERNATIONALE V ICS 29.140.99 PRICE CODE CODE PRIX ISBN 978-2-88912-830-3 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale colourinside 2 61347-2-7 IEC:2011 CONTENTS FOREWORD . 4 INTRODUCTION . 6

19、 1 Scope . 7 2 Normative references . 7 3 Terms and definitions . 8 4 General requirements . 9 5 General notes on tests . 10 6 Classification 10 7 Marking 10 8 Protection against accidental contact with live parts . 12 9 Terminals . 12 10 Provisions for protective earthing . 12 11 Moisture resistanc

20、e and insulation 12 12 Electric strength . 12 13 Thermal endurance test for windings of ballasts . 12 14 Fault conditions 12 15 Starting conditions 12 16 Lamp current 13 17 Supply current 13 18 Maximum current in any lead (with cathode preheating) . 13 19 Lamp operating current waveforms . 13 20 Fun

21、ctional safety (EBLF) 14 21 Changeover operation 15 22 Recharging device 16 23 Protection against excessive discharge 18 24 Indicator . 19 25 Remote control, rest mode, inhibition mode 19 26 Temperature cycling test and endurance test . 20 27 Polarity reversal . 20 28 Fault conditions 21 29 Construc

22、tion . 21 30 Creepage distances and clearances . 21 31 Screws, current-carrying parts and connections 21 32 Resistance to heat, fire and tracking . 21 33 Resistance to corrosion 21 34 Abnormal lamp conditions 21 35 Protection of associated components . 26 Annex A (normative) Test to establish whethe

23、r a conductive part is a live part, which may cause an electric shock . 28 Annex B (normative) Particular requirements for thermally protected lamp controlgear 28 Annex C (normative) Particular requirements for electronic lamp controlgear with means of protection against overheating . 28 61347-2-7 I

24、EC:2011 3 Annex D (normative) Requirements for carrying out the heating test of thermally protected lamp controlgear . 28 Annex E (normative) Use of constant S other than 4 500 in twtests . 28 Annex F (normative) Draught-proof enclosure 28 Annex G (normative) Explanation of the derivation of the val

25、ues of pulse voltages 29 Annex H (normative) Tests 29 Annex I (normative) Batteries for emergency lighting luminaires 29 Annex J (informative) Rest mode and inhibition mode facilities 29 Annex K (normative) Ballasts incorporating an automatic testing function for emergency lighting operation 30 Anne

26、x L (informative) Compatibility between normal mains operation electronic controlgear and battery-powered emergency operation controlgear . 33 Figure 1 Suitable circuit for the measurement of lamp current and luminous flux . 15 Figure 2 Rectifying effect test 23 Figure 3 Circuit to test whether a co

27、ntrolgear can withstand a leaking burner 24 Figure 4 Circuit to test whether a ballast can withstand rectification . 26 Figure L.1 Timing diagram: changeover operation 34 Figure L.2 Supply voltage for the function test . 35 Table 1 Voltage per cell to which the battery is discharged 16 Table 2 Relat

28、ion between r.m.s. working voltage and maximum peak voltage 26 Table K.1 Relevant requirements of IEC 62034 30 4 61347-2-7 IEC:2011 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ LAMP CONTROLGEAR Part 2-7: Particular requirements for battery supplied electronic controlgear for emergency lighting (self-

29、contained) FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardiza

30、tion in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is

31、entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the In

32、ternational Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects sin

33、ce each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content

34、 of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible

35、in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity a

36、ssessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, e

37、mployees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of

38、 the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to t

39、he possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61347-2-7 has been prepared by subcommittee 34C: Auxiliaries for lamps, of IEC technical c

40、ommittee 34: Lamps and related equipment. The text of this standard is based on the following documents: FDIS Report on voting 34C/995/FDIS 34C/1002/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This third edit

41、ion cancels and replaces the second edition published in 2006. It constitutes a technical revision. Significant changes introduced into this third edition include: 61347-2-7 IEC:2011 5 modification of IEC 61347-2-7 to become a standard exclusively for d.c. battery supplied electronic controlgear for

42、 emergency lighting (self-contained). IEC 61347-2-3 Annex J is intended to cover centrally supplied emergency controlgear; update of Clause 22 Recharging devices; modification of Clause 20 battery voltage characterisation to support EBLF measurement. This to simplify and increase reproducibility of

43、testing; rationalisation of requirements between IEC 61347-2-7 and IEC 60598-2-22 requirements of IEC 60598-2-22 being transferred to IEC 61347-2-7. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. This standard shall be used in conjunction with IEC 61347-1. This

44、part 2 supplements or modifies the corresponding clauses in IEC 61347-1. NOTE In this standard, the following print types are used: requirements: in roman type; test specifications: in italic type; notes: in small roman type. A list of all parts of the IEC 61347 series, published under the general t

45、itle Lamp controlgear, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the public

46、ation will be reconfirmed, withdrawn, replaced by a revised edition, or amended. IMPORTANT The colour inside logo on the cover page of this publication indicates that it contains colours which are considered to be useful for the correct understanding of its contents. Users should therefore print thi

47、s document using a colour printer. 6 61347-2-7 IEC:2011 INTRODUCTION The formatting into separately published parts provides for ease of future amendments and revisions. Additional requirements will be added as and when a need for them is recognized. This standard, and the parts which make up IEC 61

48、347-2, in referring to any of the clauses of IEC 61347-1, specify the extent to which such a clause is applicable and the order in which the tests are to be performed; they also include additional requirements, as necessary. All parts which make up IEC 61347-2 are self-contained and, therefore, do n

49、ot include reference to each other. Where the requirements of any of the clauses of IEC 61347-1 are referred to in this standard by the phrase “The requirements of Clause n of IEC 61347-1 apply“, this phrase is interpreted as meaning that all requirements of the clause in question of Part 1 apply, except any which are clearly inapplicable to the specific type of lamp controlgear covered by this par