IEC 61156-7 Edition 1.1-2012 Multicore and symmetrical pair quad cables for digital communications - Part 7 Symmetrical pair cables with transmission characteristics up to 1200 MHz.pdf

《IEC 61156-7 Edition 1.1-2012 Multicore and symmetrical pair quad cables for digital communications - Part 7 Symmetrical pair cables with transmission characteristics up to 1200 MHz.pdf》由会员分享，可在线阅读，更多相关《IEC 61156-7 Edition 1.1-2012 Multicore and symmetrical pair quad cables for digital communications - Part 7 Symmetrical pair cables with transmission characteristics up to 1200 MHz.pdf（32页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 61156-7 Edition 1.1 2012-12 INTERNATIONAL STANDARD NORME INTERNATIONALE Multicore and symmetrical pair/quad cables for digital communications Part 7: Symmetrical pair cables with transmission characteristics up to 1 200 MHz Sectional specification for digital and analog communication cables Cbl

2、es multiconducteurs paires symtriques et quartes pour transmissions numriques Partie 7: Cbles paires symtriques avec caractristiques de transmission jusqu 1 200 MHz Spcification intermdiaire pour cbles de transmissions numriques et analogiques IEC61156-7:2003+A1:2012 colourinsideTHIS PUBLICATION IS

3、COPYRIGHT PROTECTED Copyright 2012 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from eithe

4、r IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droit

5、s de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI

6、du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue

7、de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About

8、IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Useful links: IEC publications search - www.iec.ch/searchpub The advanced search enables you

9、 to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all ne

10、w publications released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in additional language

11、s. Also known as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. A propos de la CEI La Commission Ele

12、ctrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu

13、. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub La recherche avance vous permet de trouver des publications CEI en utilisant diffrents critres (numro de rfrence, texte

14、, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications de la CEI. Just Published dtaille les nouvelles publications parues. Disponible en ligne et au

15、ssi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement ap

16、pel Vocabulaire Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 61156-7 Edition 1.1 2012-12 INTERNATIONAL STANDARD NORME INTERNATIONALE

17、Multicore and symmetrical pair/quad cables for digital communications Part 7: Symmetrical pair cables with transmission characteristics up to 1 200 MHz Sectional specification for digital and analog communication cables Cbles multiconducteurs paires symtriques et quartes pour transmissions numriques

18、 Partie 7: Cbles paires symtriques avec caractristiques de transmission jusqu 1 200 MHz Spcification intermdiaire pour cbles de transmissions numriques et analogiques INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE ICS 33.120.20 ISBN 978-2-8322-0563-1 Registered

19、trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur a

20、gr. colourinside 2 61156-7 IEC:2003+A1:2012 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ MULTICORE AND SYMMETRICAL PAIR/QUAD CABLES FOR DIGITAL COMMUNICATIONS Part 7: Symmetrical pair cables with transmission characteristics up to 1 200 MHz Sectional specification for digital and analog communication

21、 cables FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardizatio

22、n in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is ent

23、rusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the Inter

24、national Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since

25、each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of

26、 IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in

27、their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity asse

28、ssment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, empl

29、oyees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of th

30、e publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the

31、possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. This consolidated version of IEC 61156-7 consists of the first edition (2003) documents 46C/573/FDIS and 46C/591/RVD and

32、 its amendment 1 (2012) documents 46C/956/CDV and 46C/965/RVC. It bears the edition number 1.1. The technical content is therefore identical to the base edition and its amendment and has been prepared for user convenience. A vertical line in the margin shows where the base publication has been modif

33、ied by amendment 1. Additions and deletions are displayed in red, with deletions being struck through. 61156-7 IEC:2003+A1:2012 3 International Standard IEC 61156-7 has been prepared by subcommittee 46C: Wires and symmetric cables, of IEC technical committee 46: Cables, wires, waveguides, r.f. conne

34、ctors, r.f. and microwave passive components and accessories. The bilingual version (2003-11) replaces the English version including its Corrigendum 1 (2003-09). The French version has not been voted upon. This standard is to be read in conjunction with IEC 61156-1. This publication has been drafted

35、 in accordance with the ISO/IEC Directives, Part 2. The committee has decided that the contents of the base publication and its amendments will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At th

36、is date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. IMPORTANT The “colour inside” logo on the cover page of this publication indicates that it contains colours which are considered to be useful for the correct understanding of its contents. Users shoul

37、d therefore print this publication using a colour printer. 4 61156-7 IEC:2003+A1:2012 MULTICORE AND SYMMETRICAL PAIR/QUAD CABLES FOR DIGITAL COMMUNICATIONS Part 7: Symmetrical pair cables with transmission characteristics up to 1 200 MHz Sectional specification for digital and analog communication c

38、ables 1 General 1.1 Scope This sectional specification relates to IEC 61156-1. The cables described herein may be used for various communication systems as well as for analog systems, such as video, that exist or are under development and which may use as many as four pairs simultaneously. In this s

39、ense, this sectional specification provides the cable characteristics required by system developers to evaluate new systems as well as to enhance present systems. It covers a cable having four individually screened (STP) pairs. The cable may be provided with a common screen over the cable core. The

40、transmission characteristics are specified up to a frequency of 1 200 MHz and at a temperature of 20 C. The cables covered by this sectional specification are intended to operate with voltages and currents normally encountered in communication systems. These cables are not intended to be used in con

41、junction with low impedance sources, for example, the electric power supply of public utility mains. 1.2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the l

42、atest edition of the referenced document (including any amendments) applies. IEC 60189-1:1986, Low-frequency cables and wires with PVC insulation and PVC sheath Part 1: General test and measuring methods IEC 60304, Standard colours for insulation for low-frequency cables and wires IEC 61156-1:2002,

43、Multicore and symmetrical pair/quad cables for digital communications Part 1: Generic specification IEC 61156-7-1, Multicore and symmetrical pair/quad cables for digital communications Part 7-1: Symmetrical pair cables with transmission characteristics up to 1 200 MHz Blank detail specification for

44、digital and analog communication cables IEC 62153-4-2, Metallic telecommunication cable test methods Part 4-2: Electromagnetic compatibility (EMC) Screening and coupling attenuation Injection clamp method 61156-7 IEC:2003+A1:2012 5 1.3 Installation considerations Under consideration. 1.4 Climatic co

45、nditions Under static conditions, the cables shall operate in the temperature range from 20 C to +60 C. The temperature dependence of the cables is specified for screened cables and should be taken into account for the design of actual cabling systems. The recommended temperature range during instal

46、lation should be indicated in the relevant detail specification. 2 Definitions, materials and cable construction 2.1 Definitions See 2.1 of IEC 61156-1. 2.2 Materials and cable construction 2.2.1 General remarks The choice of materials and cable construction shall be suitable for the intended applic

47、ation and installation of the cable. Particular care shall be taken to meet any special requirements for fire performance (such as burning properties, smoke generation, evolution of halogen gas, etc.). A detail specification may be prepared. 2.2.2 Cable construction The cable construction shall be i

48、n accordance with the materials, dimensions and assembly details given in the relevant detail specification. 2.2.3 Conductor The conductor shall be a solid annealed copper conductor, in accordance with 2.2.3 of IEC 61156-1, and shall have a diameter between 0,5 mm and 0,8 mm. 2.2.4 Insulation The co

49、nductor shall be insulated with a suitable thermoplastic material. Examples of suitable materials are: polyolefin; fluoropolymer; low-smoke zero-halogen thermoplastic material. The insulation may be solid or cellular with or without a solid dielectric skin. The insulation shall be continuous and shall have a thickness such that the completed cable meets the specified requirements. The nominal