IEC 60793-2-60-2008 Optical fibres - Part 2-60 Product specifications - Sectional specification for category C singles-mode intraconnection fibres《光纤.第2-60部分 产品规范.C型单模内连接光纤用分规范》.pdf

《IEC 60793-2-60-2008 Optical fibres - Part 2-60 Product specifications - Sectional specification for category C singles-mode intraconnection fibres《光纤.第2-60部分 产品规范.C型单模内连接光纤用分规范》.pdf》由会员分享，可在线阅读，更多相关《IEC 60793-2-60-2008 Optical fibres - Part 2-60 Product specifications - Sectional specification for category C singles-mode intraconnection fibres《光纤.第2-60部分 产品规范.C型单模内连接光纤用分规范》.pdf（50页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 60793-2-60 Edition 1.0 2008-02 INTERNATIONAL STANDARD NORME INTERNATIONALE Optical fibres Part 2-60: Product specifications Sectional specification for category C single- mode intraconnection fibres Fibres optiques Partie 2-60: Spcifications de produits Spcification intermdiaire pour fibres uni

2、modales dintraconnexion de catgorie C IEC 60793-2-60:2008 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2008 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical,

3、including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address be

4、low or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie

5、et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CE

6、I de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes Internati

7、onal Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Useful links:

8、IEC publications search - www.iec.ch/searchpub The advanced search enables you to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublis

9、hed Stay up to date on all new IEC publications. Just Published details all new publications released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and d

10、efinitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contac

11、t the Customer Service Centre: csciec.ch. A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publica

12、tions CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub La recherche avance vous permet de trouve

13、r des publications CEI en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications de la CEI. Just

14、Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais,

15、 ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch

16、. IEC 60793-2-60 Edition 1.0 2008-02 INTERNATIONAL STANDARD NORME INTERNATIONALE Optical fibres Part 2-60: Product specifications Sectional specification for category C single- mode intraconnection fibres Fibres optiques Partie 2-60: Spcifications de produits Spcification intermdiaire pour fibres un

17、imodales dintraconnexion de catgorie C INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE T ICS 33.180.10 PRICE CODE CODE PRIX ISBN 978-2-83220-353-8 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique

18、 Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. 2 60793-2-60 IEC:2008 CONTENTS FOREWORD . 4 1 Scope . 6 2 Normative references . 7 3 Terms, definitio

19、ns, symbols and abbreviations 8 3.1 Terms and definitions 8 3.2 Symbols and abbreviations 8 4 Specifications . 8 4.1 Dimensional requirements . 8 4.2 Mechanical requirements . 9 4.3 Transmission requirements . 9 4.4 Environmental requirements 10 4.4.1 Transmission requirements 11 4.4.2 Mechanical re

20、quirements . 11 Annex A (normative) Family specification for C1 single-mode fibre 13 Annex B (normative) Family specification for C2 single-mode fibre . 16 Annex C (normative) Family specification for C3 single-mode fibre 19 Annex D (normative) Family specification for C4 single-mode fibre 21 Biblio

21、graphy 23 Table 1 List of families and main differences 6 Table 2 Dimensional attributes and measurement methods 8 Table 3 Requirements common to class C fibres 9 Table 4 Mechanical attributes and measurement methods . 9 Table 5 Mechanical requirements common to class C fibres 9 Table 6 Transmission

22、 attributes and measurement methods 10 Table 7 Transmission requirements common to class C fibres . 10 Table 8 Transmission attributes required in family specifications . 10 Table 9 Environmental attributes and test methods 10 Table 10 Environment dependant mechanical or transmission attributes and

23、test methods 11 Table 11 Tensile strength requirements common to class C fibres . 11 Table 12 Stress corrosion susceptibility requirements common to class C fibres 12 Table A.1 Dimensional requirements for C1 fibres 13 Table A.2 Mechanical requirements for C1 fibres . 13 Table A.3 Transmission requi

24、rements for C1 fibres 14 Table A.4 Environment dependant transmission requirements for C1 fibres . 14 Table A.5 Environment dependant mechanical requirements for C1 fibres . 15 Table B.1 Dimensional requirements for C2 fibres 16 Table B.2 Mechanical requirements for C2 fibres . 16 Table B.3 Transmis

25、sion requirements for C2 fibres 17 60793-2-60 IEC:2008 3 Table B.4 Environment dependant transmission requirements for C2 fibres . 17 Table B.5 Environment dependant mechanical requirements for C2 fibres . 18 Table C.1 Dimensional requirements for C3 fibres . 19 Table C.2 Mechanical requirements for

26、 C3 fibres . 19 Table C.3 Transmission requirements for C3 fibres 20 Table C.4 Environment dependant transmission requirements for C3 fibres . 20 Table C.5 Environment dependant mechanical requirements for C3 fibres . 20 Table D.1 Dimensional requirements for C4 fibres . 21 Table D.2 Mechanical requ

27、irements for C4 fibres . 21 Table D.3 Transmission requirements for C4 fibres 22 Table D.4 Environment dependant transmission requirements for C4 fibres . 22 4 60793-2-60 IEC:2008 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ OPTICAL FIBRES Part 2-60: Product specifications Sectional specification for

28、 category C single-mode intraconnection fibres FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on

29、all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Pub

30、lication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation.

31、 IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of

32、 opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made

33、 to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transpar

34、ently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be re

35、ndered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of

36、 its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any

37、other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be

38、the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60793-2-60 has been prepared by subcommittee 86A: Fibres and cables, of IEC technical committee 86: Fibre optics. This bilingual version (2012-09) corresponds to

39、the monolingual English version, published in 2008-02.The text of this standard is based on the following documents: CDV Report on voting 86A/1160A/CDV 86A/1201/RVC Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. The

40、 French version of this standard has not been voted upon. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. 60793-2-60 IEC:2008 5 A list of all parts of the IEC 60793 series can be found, under the general title Optical Fibres, on the IEC website. The committee has

41、 decided that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed; withdrawn; replaced by a revised edit

42、ion; or amended. 6 60793-2-60 IEC:2008 OPTICAL FIBRES Part 2-60: Product specifications Sectional specification for category C single-mode intraconnection fibres 1 Scope This part of IEC 60793 is applicable to optical fibre types C1, C2, C3, C4, as described in Table 1. These fibres are used for the

43、 intraconnections within or between components or photonic systems or subsystems. While the fibres are sold in lengths on the scale of kilometres, they are normally cut into short lengths for use in these intraconnections. While the fibres could be overcoated or buffered for the purpose of making pr

44、otected pigtails, they may be used without overcoating. They may, however, be colour-coded. The general requirements defined in IEC 60793-2 apply to these fibres. Specific requirements that are common to these fibres are found in the body of this text. Particular requirements for individual fibre ty

45、pes or applications are defined in Annexes A, B, C and D, which refer to normative family specifications. These family specifications are distinguished based on optimum transmission wavelengths and nominal Mode Field Diameter (MFD), which affects splice loss. For each family specification, there are

46、 two sub-categories that are distinguished on the basis of the cladding diameter and other related attributes. The conventional nominal cladding diameter of 125 m is augmented with the reduced cladding type product with a nominal diameter of 80 m. These are distinguished with the suffixes: “_125” or

47、 “_80”. For example C1 fibre can be selected as either C1_125 or C1_80. The transmission characteristics of the two cladding diameter choices should be the same. For each family specification except C1, there are two sub-categories that are distinguished on the basis of transmission characteristics

48、that relate to MFD. To denote these sub- categories, a “_a“ or “_b“ suffix is added, for lower or higher MFD. In general, the fibres can be optimised for either splice loss or macro-bend loss using MFD as a main variable. A C2 fibre with 80 m cladding diameter and lower MFD is designated as C2_80_a.

49、 Fibres for the C1_125 family specification can be selected fom category B1.1 or B1.3 single- mode fibres and are suitable for use with any category B single-mode fibre at wavelengths from 1 280 nm to 1 625 nm. Fibres for the C2 and C3 family specifications are optimized at nominal wavelengths of 1 310 nm and 1 550 nm respectively for connection to any category B single-mo