UL 1691 CRD-2017 UL Standard for Safety Single Pole Locking-Type Separable Connectors - Section Paragraph Reference Supplement SA Subject Supplement SA Replacement Enclosure (Hous.pdf

《UL 1691 CRD-2017 UL Standard for Safety Single Pole Locking-Type Separable Connectors - Section Paragraph Reference Supplement SA Subject Supplement SA Replacement Enclosure (Hous.pdf》由会员分享，可在线阅读，更多相关《UL 1691 CRD-2017 UL Standard for Safety Single Pole Locking-Type Separable Connectors - Section Paragraph Reference Supplement SA Subject Supplement SA Replacement Enclosure (Hous.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULUNDERWRITERS LABORATORIES INC. CERTIFICATION REQUIREMENT DECISIONThis Certification Requirement Decision is prepared by UL LLC. It is normative for the applicable ULProduct Certification Program(

2、s); however, it is currently not part of the UL Standard(s) referencedbelow.Product Category (CCN): RUUSStandard Number: UL 1691Standard Title: Standard for Single Pole Locking-Type Separable ConnectorsEdition Date: February 29, 2012Edition Number: 1Section / Paragraph Reference: Supplement SASubjec

3、t: Supplement SA: Replacement Enclosure (Housing) for use with specificmanufacturers Single Pole Locking Type Separable Attachment Plug and CordConnector :DECISION:Addition of new Supplement SA:SUPPLEMENT SA REPLACEMENT ENCLOSURE FOR USE WITH SPECIFIC MANUFACTURERSSINGLE POLE LOCKING-TYPE SEPARABLE

4、ATTACHMENT PLUG and CABLE CONNECTORINTRODUCTIONSA1 ScopeSA1.1 These requirements cover replacement enclosure (housing) (see SA3.1) intended for use in thespecific manufacturers single pole locking-type separable attachment plug and cable connector.SA2 GeneralSA2.1 In addition to complying with Secti

5、ons SA3 SA8 of these requirements, the replacementenclosure (housing) alone, and in combination with the complete device (attachment plug and cableconnector, respectively), shall comply with the applicable Construction and Performance requirements inthe main body of this Standard.SA3 DefinitionsSA3.

6、1 REPLACEMENT ENCLOSURE (PART) An individual replacement enclosure (housing) identifiedby the manufacturer for use in the same manufacturers complete device (single pole locking-typeseparable attachment plug and cable connector, respectively).Note: The replacement part is packaged as a “kit” contain

7、ing the individual part and installation instructions (See Section SA8 of thisSupplement).CONSTRUCTIONSA4 GeneralUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULSA4.1 The replacement enclosure (housing) shall be formed and assembled so that it

8、 can be installed, inaccordance with the installation instructions, into its specified single pole locking-type separableattachment plug and cable connector without risk of fire or electric shock. Risk of fire or electric shock isdetermined by compliance with the construction and performance require

9、ments herein and the applicablerequirements of the main body of this Standard.SA4.2 A replacement enclosure (housing) part shall only be installed using commonly used tools such asa screw driver or a wrench. A replacement enclosure (housing) shall not be permitted that requires theinstaller to remov

10、e or defeat or replace a factory installed securement means such as a rivet or drive pin.PERFORMANCESA5 GeneralSA5.1 If the replacement enclosure (housing) is recommended for use with more than one device, eachrepresentative combination of replacement enclosure (housing) and device shall be evaluate

11、d.SA6 Replacement Part Assembly TestSA6.1 The replacement enclosure (housing) shall be able to be installed in the specified device and shallbe reliably retained in place without causing an increased risk of fire or electric shock. Compliance isdetermined by inspection and the test of SA6.2 shall be

12、 performed.SA6.2 A sample of the replacement enclosure (housing) shall be assembled to its specified device usingthe manufacturers installation instructions. Upon completion of the assembly, the integrity of thecompleted assembly shall be examined and if necessary, subjected to the applicable perfor

13、mance testingnecessary to maintain continued compliance with this Standard.MARKINGSSA7 GeneralSA7.1 The replacement enclosure (housing) shall be provided in the form of a kit, including marking asdetailed in Section SA7 of this Supplement.SA7.2 A required marking shall be molded, die-stamped, paint-

14、stenciled, stamped or etched metal that ispermanently secured, or indelibly stamped lettering on a pressure-sensitive label secured by adhesivethat, upon investigation, meets the intent of the requirement for the application.SA7.3 The replacement enclosure (housing) shall be provided with the follow

15、ing identification markings:a) Manufacturers name,b) Specific catalog or series number, andc) The date or other dating period of manufacture not exceeding any three consecutive months.Abbreviation of the date of manufacture, or provision in a nationally accepted conventional code or in acode affirme

16、d by the manufacturer, meets the intent of the requirement.STANDARD NUMBER: UL 1691 -2-UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULSA7.4 The replacement enclosure (housing) packaging shall be marked with the following marking orequivalent:

17、 WARNING Use only replacement part (Catalog Number) with (+) Attachment Plug or CordConnector”, where “(+)” is to be replaced with the specific manufacturer name and model/catalog numberof the intended device(s).INSTRUCTIONSSA8 GeneralSA8.1 The replacement enclosure (housing) shall be provided with

18、instructions pertaining to itsinstallation, operation, and maintenance, as applicable.SA8.2 An illustration may be used to clarify the intent of a required instruction but shall not replace thewritten instruction.SA8.3 Instructions shall include the following statements or their equivalent:IMPORTANT

19、 SAFETY INSTRUCTIONSWARNING Use only replacement enclosure (housing) (Catalog Number) with (+) Attachment Plug orCord Connector Only, where (+) is to be replaced with the specific manufacturer name and model/catalognumber of the intended device(s).WARNING Risk of Fire or Electric Shock. Do not use t

20、his replacement enclosure (housing) with anyattachment plug or cord connector (as appropriate), other than the one specified on the replacement markpackaging and in these instructions.SAVE THESE INSTRUCTIONSSA8.4 The opening and closing statements of the instructions specified in SA8.3 IMPORTANTSAFE

21、TY INSTRUCTIONS, and SAVE THESE INSTRUCTIONS, or the equivalent shall be entirely inupper case letters or shall be emphasized to distinguish them from the rest of the text.RATIONALE FOR DECISION:It was brought to ULs attention that single pole locking-type separable attachment plug and cableconnecto

22、rs are routinely repaired in the field. Manufacturers provide replacement enclosure (housing) partin the form of a “kit” to serve this purpose. To address this need to ensure continued compliance with theStandard, UL has developed requirements contained in a new UL 1691 Supplement SA, “ReplacementEn

23、closure (housing) for use with specific manufacturers single pole locking-type separable attachmentplug and cable connectors.”This proposal is also consistent with UL 1682 Supplement SA which already provides a similar path formanufacturers to provide replacement parts.Copyright 2017 UL LLCUL LLC, i

24、n performing its functions in accordance with its objectives, does not guarantee or warrant thecorrectness of Certification Requirement Decisions it may issue or that they will be recognized or adoptedby anyone. Certification Requirement Decisions are the opinion of UL LLC. in practically applying t

25、herequirements of the standard. They do not represent formal interpretations of the standard underAmerican National Standards Institute (ANSI) processes. UL LLC shall not be responsible to anyone forthe use of or reliance upon Certification Requirement Decisions by anyone. UL LLC shall not incur any

26、STANDARD NUMBER: UL 1691 -3-UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULobligation or liability for damages, including consequential damages, arising out of or in connection withthe use or reliance upon Certification Requirement Decisions. The electronic version of the CertificationRequirement Decision is the current version and previously printed copies may be outdated.This document is published as a service to ULs certification customersSTANDARD NUMBER: UL 1691 -4-