SANS 8665-2008 Small craft - Marine propulsion reciprocating internal combustion engines - Power measurements and declarations《小艇 海运推进式往复内燃机 功率测量和声明》.pdf

《SANS 8665-2008 Small craft - Marine propulsion reciprocating internal combustion engines - Power measurements and declarations《小艇 海运推进式往复内燃机 功率测量和声明》.pdf》由会员分享，可在线阅读，更多相关《SANS 8665-2008 Small craft - Marine propulsion reciprocating internal combustion engines - Power measurements and declarations《小艇 海运推进式往复内燃机 功率测量和声明》.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-21973-4 SANS 8665:2008 Edition 1 ISO 8665:2006 Edition 3SOUTH AFRICAN NATIONAL STANDARD Small craft Marine propulsion reciprocating intern

4、al combustion engines Power measurements and declarations This national standard is the identical implementation of ISO 8665:2006, and is adopted with the permission of the International Organization for Standardization. Published by SABS Standards Division 1 Dr Lategan Road Groenkloof Private Bag X

5、191 Pretoria 0001 Tel: +27 12 428 7911 Fax: +27 12 344 1568 www.sabs.co.za SABS This standard may only be used and printed by approved subscription and freemailing clients of the SABS.SANS 8665:2008 Edition 1 ISO 8665:2006 Edition 3 Table of changes Change No. Date Scope National foreword This South

6、 African standard was approved by National Committee SABS TC 188, Small craft, in accordance with procedures of the SABS Standards Division, in compliance with annex 3 of the WTO/TBT agreement. This SANS document was published in September 2008. This standard may only be used and printed by approved

7、 subscription and freemailing clients of the SABS. Reference number ISO 8665:2006(E) ISO 2006INTERNATIONAL STANDARD ISO 8665 Third edition 2006-06-01 Small craft Marine propulsion reciprocating internal combustion engines Power measurements and declarations Petits navires Moteurs marins de propulsio

8、n alternatifs combustion interne Mesurage et dclaration de la puissance SANS 8665:2008This standard may only be used and printed by approved subscription and freemailing clients of the SABS.ISO 8665:2006(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licens

9、ing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO

10、Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been

11、 taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2006 All rights reserved. Unless otherwise specified, no part of this publication may be reprod

12、uced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 74

13、9 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2006 All rights reservedSANS 8665:2008This standard may only be used and printed by approved subscription and freemailing clients of the SABS.ISO 8665:2006(E) ISO 2006 All rights reserved iii Forewo

14、rd ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technic

15、al committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of el

16、ectrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to t

17、he member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for id

18、entifying any or all such patent rights. ISO 8665 was prepared by Technical Committee ISO/TC 188, Small craft. This third edition cancels and replaces the second edition (ISO 8665:1994), which has been technically revised. SANS 8665:2008This standard may only be used and printed by approved subscrip

19、tion and freemailing clients of the SABS.SANS 8665:2008This standard may only be used and printed by approved subscription and freemailing clients of the SABS.INTERNATIONAL STANDARD ISO 8665:2006(E) ISO 2006 All rights reserved 1 Small craft Marine propulsion reciprocating internal combustion engine

20、s Power measurements and declarations 1 Scope This International Standard specifies the requirements additional to ISO 15550 for determining the power of marine propulsion reciprocating internal combustion (RIC) engines when presented for documenting and checking of the declared (rated) power publis

21、hed by the manufacturer. This International Standard applies to engines used for propulsion of recreational craft and other small craft of up to 24 m hull length. This International Standard is to be used in conjunction with ISO 15550. NOTE For determination of power for exhaust emission tests accor

22、ding to ISO 8178, ISO 14396 applies. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments

23、) applies. ISO 3104:1994, Petroleum products Transparent and opaque liquids Determination of kinematic viscosity and calculation of dynamic viscosity ISO 3675:1998, Crude petroleum and liquid petroleum products Laboratory determination of density Hydrometer method ISO 5165:1998, Petroleum products D

24、etermination of the ignition quality of diesel fuels Cetane engine method ISO 15550:2002, Internal combustion engines Determination and method for the measurement of engine power General requirements 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 15

25、550 and the following apply. 3.1 declared engine speed spark-ignition engines without speed governor speed at the mid-point of the full throttle speed range recommended by the manufacturer for propeller selection 4 Symbols For the purposes of this document, the symbols given in ISO 15550:2002, Table

26、 2, apply. SANS 8665:2008This standard may only be used and printed by approved subscription and freemailing clients of the SABS.ISO 8665:2006(E) 2 ISO 2006 All rights reserved5 Standard reference conditions The standard reference conditions used in ISO 15550:2002, Clause 5, apply. 6 Test methods 6.

27、1 General Test method 2 according to ISO 15550:2002, 6.3, applies. 6.2 Test conditions ISO 15550:2002, 6.3.4.1 to 6.3.4.14, applies with the following additions. 6.2.1 The test engine or propulsion system shall be representative of the manufacturers production units. All auxiliaries fitted shall be

28、listed and described. 6.2.2 All equipment and auxiliaries not required by ISO 15550:2002, Table 1, column 3, shall be removed before the test. Auxiliaries not necessary for propulsion of the craft in which the engine is intended to be installed and which may be mounted on the engine shall be removed

29、 for the test. The following auxiliaries are given as examples: air-conditioning system compressor; flush/bilge pump. Where auxiliaries cannot be removed they shall be operated under no-load conditions. 6.2.3 Fuel used for power measurement of spark-ignition engines shall conform to the engine manuf

30、acturers recommendation. 6.2.4 Fuel used for power measurement of diesel (compression-ignition) engines shall meet the following specification: Table 1 Limits Property Units min. max. Method Density at 15 C kg/m 3835 845 ISO 3675:1998 Viscosity at 40 C mm 2 /s 2,5 3,6 ISO 3104:1994 Cetane number 49,

31、0 53,0 ISO 5165:1998 For diesel (compression-ignition) engines operating on distillate fuel, the fuel temperature shall be (313 3) K. NOTE This requirement is not applicable to diesel engines running on intermediate or heavy fuels. 6.2.5 Lubricating oil used shall conform to the engine manufacturers

32、 recommendations. Record the lubricating oil type and, if applicable, viscosity of lubricant. 6.2.6 For outboard engines the cowl, if supplied as standard equipment, shall be regarded as a part of the air inlet system. SANS 8665:2008This standard may only be used and printed by approved subscription

33、 and freemailing clients of the SABS.ISO 8665:2006(E) ISO 2006 All rights reserved 3 6.2.7 If the exhaust system as delivered is not complete, the back-pressure at the declared engine speed shall be within 0,75 kPa of the maximum back-pressure at which the declared power can be achieved, as specifie

34、d by the manufacturer. If the exhaust system as delivered is complete, the laboratory exhaust system shall maintain the exhaust pressure at the unit outlet within 0,75 kPa of the barometric pressure at the test bed. 6.2.8 If the engine air inlet is connected to a laboratory air system, the system sh

35、all supply air to the engine within 0,75 kPa of the barometric pressure at the test bed. 6.2.9 For liquid-cooled engines, the temperature of the coolant at the raw-water inlet shall be maintained at 298 K 15 K (25 C 15 C) except that for engines with charge air cooler the temperature shall be mainta

36、ined at 298 K 5 K (25 C 5 C). The raw-water coolant inlet pressure shall not exceed 50 kPa. Propulsion systems not fitted with a raw-water pump are exempted from this requirement. The coolant outlet temperature shall be within the range specified by the manufacturer if such a range is specified. 6.3

37、 Production conformity test/manufacturing tolerance The declared power shall indicate the average run-in power measured on engines in production. In a production conformity test the measured power at declared speed of any individual marine propulsion engine or propulsion system shall not deviate fro

38、m the declared power by more than a) 5 % for engines or propulsion systems with speed governors of more than 100 kW declared power, or b) 10 % or 0,45 kW, whichever is greater, for all other engines and propulsion systems. 7 Method of power correction The method of power correction according to ISO

39、15550:2002, Clause 7, applies. 8 Measurement of exhaust emissions ISO 15550:2002, Clause 8, does not apply. 9 Test report 9.1 General ISO 15550:2002, 9.2, applies with the following addition. The presentation of ISO 15550:2002, 9.2.2.4, Table 13, does not apply and shall be replaced by the following

40、: engine speed; torque; intake air temperature and pressure (see ISO 15550:2002, 6.3.4.3); fuel temperature for diesel (compression-ignition) engines only (see 6.2.4); ambient air temperature of the atmosphere (see ISO 15550:2002, 6.3.4.2); SANS 8665:2008This standard may only be used and printed by

41、 approved subscription and freemailing clients of the SABS.ISO 8665:2006(E) 4 ISO 2006 All rights reserved barometric pressure at the test bed (see ISO 15550:2002, 6.3.4.2); humidity (see ISO 15550:2002, 6.3.4.2); power correction factor (see ISO 15550:2002, Clause 7); laboratory exhaust system pres

42、sure (see 6.2.7); lubricating oil temperature (see ISO 15550:2002, 6.3.4.12); coolant temperature at raw-water inlet and engine outlet (see 6.3.4.10 in ISO 15550:2002 and 6.2.9 in this International Standard); raw-water coolant supply pressure (see 6.2.9); exhaust back-pressure (see 6.2.7); fuel spe

43、cification, only required for diesel engines (see 6.2.4). The following optional data should be recorded where applicable or for safety of operation: a) lubricating oil pressure; b) intake air temperature and pressure inside the air intake manifold; c) exhaust gas temperature; d) ignition or injecti

44、on timing or ignition advance curve for engines equipped with electronic control; e) fuel supply pressure at supply-pump outlet; f) fuel consumption per unit of time. 9.2 Declaration of data 9.2.1 Declaration of power A statement of a single value of declared power shall be accompanied by a statemen

45、t of the declared engine speed. The declaration of power shall always indicate whether the power is propeller-shaft power or crankshaft power. 9.2.2 Declaration of propeller-shaft power The propeller-shaft power shall be declared for engines sold with a complete propulsion unit or at the coupling to

46、 the propeller shaft of engines sold with reduction and/or reversing gear. 9.2.3 Exhaust back-pressure The declaration of power shall be accompanied by a statement of maximum permissible exhaust back- pressure at which the declared power can be achieved. 9.2.4 Alternative presentation Power and engi

47、ne speed may alternatively be presented as a power curve (see Annexes A and B). 9.2.5 Reference to ISO 8665 Reference shall be made to ISO 8665. SANS 8665:2008This standard may only be used and printed by approved subscription and freemailing clients of the SABS.ISO 8665:2006(E) ISO 2006 All rights

48、reserved 5 Annex A (informative) Alternative method for presentation of power for engines sold with a complete propulsion unit Key 1 full load propeller-shaft power 2 propeller-shaft power Figure A.1 Propeller-shaft power at full load and propeller-shaft power at calculated propeller load (exponent

49、2,5) SANS 8665:2008This standard may only be used and printed by approved subscription and freemailing clients of the SABS.ISO 8665:2006(E) 6 ISO 2006 All rights reservedAnnex B (informative) Alternative method for presentation of power for engines sold without transmission Key 1 full load crankshaft power Figure B.1 Full load crankshaft power SANS 8665:2008This standard may only be used and printed by approved subscription and freemailing cl